summaryrefslogtreecommitdiff
path: root/target/linux/lantiq/base-files/etc
AgeCommit message (Collapse)Author
2014-04-11lantiq: more vdsl related cleanupsblogic
* atm module needs to be loaded before linux-atm * use absolute firmware paths * extended validation * add a script for mounting an optional firmware partition Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40460 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-04-10lantiq: move the dsl-modem config to network.@dsl-modem[-1]blogic
make sure uci_defaults generates a proper uci config for the v/adsl modem Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40439 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-04-03lantiq: BT Home Hub 2B support - userspaceblogic
Basic userspace configuration for BT Home Hub 2B Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40371 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-03-30lntiq: add support for Astoria ARV7519RW.blogic
These patches add support for the Astoria ARV7519RW aka Livebox 2.1 The PCI and PCIe interfaces have been disabled. Also, because there are two revisions of this board with different GPHY firmwares, two targets were defined. V2: rewrote partitions to work with an u-boot specifically made for these boards. Signed off by: Esteban Benito <estebanjbs@gmail.com> Signed off by: Carles Gadea <carlesgrg@gmail.com> Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40329 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-03-30lantiq: do an endianness swap to the RT2860 eeprom for ARV752DPW(22)blogic
ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in flash as big-endian, but the driver needs it in little-endian format. We have to swab it before handing it over. This requires my earlier patch for busybox. Funnily enough, ARV752DPW works also with the incorrect eeprom, but undoubtedly unoptimally. I have a hunch that also the final remaining Lantiq board would require this swabbing, but I'm not sure, so I just swab it in the three boards that I know about. v2: * Swab also on ARV7510PW22 based on feedback from Alvaro Rojas * Fix the offset with bs=2 Signed-off-by: Matti Laakso <malaakso at elisanet.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40328 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-03-30lantiq: add esiblogic
http://patchwork.openwrt.org/patch/3703/ Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40326 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-03-30lantiq: fix initial VLAN conf for P2601HNFXblogic
Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40321 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-03-30lantiq: add support for Arcadyan ARV7519PWblogic
This patch adds almost full support for this board. - WiFi is still not working - USB will not power up. According to some reports, it may be a passive port Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40319 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-03-30lantiq: add support for ZyXEL P2812HNUFXblogic
This patch adds almost full support for this board. WiFi is still not working. The FXS ports are not functional due to missing support for the TAPI driver on VR9 SoC. Signed-off-by: Antonios Vamporakis <ant@area128.com> Tested-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40317 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-15lantiq: Add support for Astoria ARV7510PW22blogic
This board is pretty similar to ARV752DPW22. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39303 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-12lantiq: improve Arcadyan ARV4510PW supportblogic
Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is severely lacking. This patch brings it up-to-date. Signed-off-by: Matti Laakso <malaakso@elisanet.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39230 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-11lantiq: DGN3500 fixupsblogic
Just fixing up a few things for the Netgear DGN3500. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38733 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-11lantiq: remove old hotplug handlerblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38727 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-07lantiq: fix TDW8970 lan/wan macblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38677 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-07lantiq: Fix ar8216 switch configuration for WBMR-HP-G300H devicesblogic
The switch is renamed to "switch0" in newer (3.10) linux kernels. Configure the switch using vlans by default and only configure the physical switch ports that are present. Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk> Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38673 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-08lantiq: fix up diag.shblogic
init no longer exists as a parameter Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38342 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-19lantiq: add support for ZyXEL P2601HNFXluka
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38049 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-19lantiq: add support for ZTE H201Lluka
Signed-off-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38048 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-06lantiq: add (incomplete) support for Aztech GR7000luka
*) can not connect to switch chip *) only one usb port is working *) wifi is not working Signed-off-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37712 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-05lantiq: several a803 related fixesblogic
based on work from Matti Laasko that he posted in the wiki Signed-off-by: John Crispin <blogic@openwrt.or git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37704 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01lantiq: fix VG3503J ethernet/gphy led supportblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37634 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-25lantiq: add a hook to make leds work on the secondary usb busblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37538 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-15lantiq: update ralink wlan firmware hotplug script for new eeprom sizenbd
Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37334 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-10lantiq: diag.sh with both red and green power LEDsblogic
This provides a boot LED sequence suitable for devices with both red and green LEDs for power. This assumes no "default-on" settings in the device tree. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36899 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30lantiq: Fix ar8216 switch configurationblogic
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36782 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30lantiq: DGN3500 supportblogic
This requires all the preceding patches and finishes support for the DGN3500, also removing an obsolete file. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36781 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30lantiq: fix LED-handling oversightsblogic
This reassigns the PPPoE status to the LED that was intended to indicate it, rather than the DSL sync light. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36777 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-25lantiq: make leds and network work on VG3503Jblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36445 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-09Adapt default network configuration for IPv6cyrus
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36278 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-03[lantiq] Migrate lantiq platform to common led helper functionsblogic
http://patchwork.openwrt.org/patch/3316/ Signed-off-by: Michael Heimpold <mhei@heimpold.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36187 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-12[lantiq] add support for AudioCodes AC-252blogic
user-space support for extracting the EEPROM for the RaLink WiFi is still missing. Besides this, it's all working. Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35990 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-18all targets: use numerically prefixed uci-defaults file names to better ↵jow
control order of execution git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35217 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-21[lantiq] default switch setup for WBMRblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34838 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-21[lantiq] adds script to set wps info on boards with a wps buttonblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34836 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-21[lantiq] improve button handlingblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34823 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-19Do not use deprecated path to functions.sh (/etc/functions.sh -> ↵mirko
/lib/functions.sh) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34793 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-19[lantiq] minor basefiles fixesblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34790 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-15[lantiq] cleanup basefilesblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34698 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-09-06lantiq: fix sx76x default uci network configurationluka
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33324 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-04uboot-envtools: update to 2012.04.01luka
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32051 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-29lantiq: use the generic uci-default functions for initial LED setupjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31995 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-23[lantiq] Adding wifi eeprom extract for ARV752DPW - Easybox 802blogic
Signed-off-by: Christian Rustmeier <rustmeier a.t. gmail dotty com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31443 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-21[target/linux/lantiq] change /etc/config/network according to actual VLAN ↵mirko
config to enable LAN port 4 on the ARV4520PW board The VLAN mapping on the ARV4520PW board is the following: port on Router: | VLAN in software: LAN 1 | 3 LAN 2 | 2 LAN 3 | 1 LAN 4 | 0 DSL | 4 So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31391 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-25[lantiq] update /etc/uci-defaults/*blogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31062 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-14[lantiq] generate uboot environment data in targetblogic
With this patch it is possible to generate uboot environment config file inside lantiq target. Currently it is only supporting GIGASX76X board. uboot environment config is used by fw_printenv fw_setenv tools. Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30537 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-14[ltq-dsl] add annex selection support to ltq_dsl packageblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30518 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-17[lantiq] gigaset 76xblogic
* fixes leds * adds all leds found on the sx763 board * removes board_config from flash layout because wireless data is stored in kernel (ath5k) * fix button handling Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29763 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-22lantiq:blogic
* fixes ath5k eeprom handling * fixes sx76x * adds sx76x to userland api * minor style cleanups Signed-of-by: Andrej Vlašić <andrej.vlasic0@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29292 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-15lantiq: add runtime generation of /etc/config/networkblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29161 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: add uci-defaults code for handling ledsblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29004 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.46.0) at 2025-01-04 10:16:24 +0000