diff options
Diffstat (limited to 'target/linux/etrax/files-2.6.25/drivers/usb/host/hc-crisv10.h')
| -rw-r--r-- | target/linux/etrax/files-2.6.25/drivers/usb/host/hc-crisv10.h | 333 |
1 files changed, 333 insertions, 0 deletions
diff --git a/target/linux/etrax/files-2.6.25/drivers/usb/host/hc-crisv10.h b/target/linux/etrax/files-2.6.25/drivers/usb/host/hc-crisv10.h new file mode 100644 index 0000000000..58a0b6238b --- /dev/null +++ b/target/linux/etrax/files-2.6.25/drivers/usb/host/hc-crisv10.h @@ -0,0 +1,333 @@ +#ifndef __LINUX_ETRAX_USB_H +#define __LINUX_ETRAX_USB_H + +#include <linux/types.h> +#include <linux/list.h> + +struct USB_IN_Desc { + volatile __u16 sw_len; + volatile __u16 command; + volatile unsigned long next; + volatile unsigned long buf; + volatile __u16 hw_len; + volatile __u16 status; +}; + +struct USB_SB_Desc { + volatile __u16 sw_len; + volatile __u16 command; + volatile unsigned long next; + volatile unsigned long buf; +}; + +struct USB_EP_Desc { + volatile __u16 hw_len; + volatile __u16 command; + volatile unsigned long sub; + volatile unsigned long next; +}; + + +/* Root Hub port status struct */ +struct crisv10_rh { + volatile __u16 wPortChange[2]; + volatile __u16 wPortStatusPrev[2]; +}; + +/* HCD description */ +struct crisv10_hcd { + spinlock_t lock; + __u8 num_ports; + __u8 running; +}; + + +/* Endpoint HC private data description */ +struct crisv10_ep_priv { + int epid; +}; + +/* Additional software state info for a USB Controller epid */ +struct etrax_epid { + __u8 inuse; /* !0 = setup in Etrax and used for a endpoint */ + __u8 disabled; /* !0 = Temporarly disabled to avoid resubmission */ + __u8 type; /* Setup as: PIPE_BULK, PIPE_CONTROL ... */ + __u8 out_traffic; /* !0 = This epid is for out traffic */ +}; + +/* Struct to hold information of scheduled later URB completion */ +struct urb_later_data { + struct delayed_work dws; + struct usb_hcd *hcd; + struct urb *urb; + int urb_num; + int status; +}; + + +typedef enum { + STARTED, + NOT_STARTED, + UNLINK, +} crisv10_urb_state_t; + + +struct crisv10_urb_priv { + /* Sequence number for this URB. Every new submited URB gets this from + a incrementing counter. Used when a URB is scheduled for later finish to + be sure that the intended URB hasn't already been completed (device + drivers has a tendency to reuse URBs once they are completed, causing us + to not be able to single old ones out only based on the URB pointer.) */ + __u32 urb_num; + + /* The first_sb field is used for freeing all SB descriptors belonging + to an urb. The corresponding ep descriptor's sub pointer cannot be + used for this since the DMA advances the sub pointer as it processes + the sb list. */ + struct USB_SB_Desc *first_sb; + + /* The last_sb field referes to the last SB descriptor that belongs to + this urb. This is important to know so we can free the SB descriptors + that ranges between first_sb and last_sb. */ + struct USB_SB_Desc *last_sb; + + /* The rx_offset field is used in ctrl and bulk traffic to keep track + of the offset in the urb's transfer_buffer where incoming data should be + copied to. */ + __u32 rx_offset; + + /* Counter used in isochronous transfers to keep track of the + number of packets received/transmitted. */ + __u32 isoc_packet_counter; + + /* Flag that marks if this Isoc Out URB has finished it's transfer. Used + because several URBs can be finished before list is processed */ + __u8 isoc_out_done; + + /* This field is used to pass information about the urb's current state + between the various interrupt handlers (thus marked volatile). */ + volatile crisv10_urb_state_t urb_state; + + /* In Ctrl transfers consist of (at least) 3 packets: SETUP, IN and ZOUT. + When DMA8 sub-channel 2 has processed the SB list for this sequence we + get a interrupt. We also get a interrupt for In transfers and which + one of these interrupts that comes first depends of data size and device. + To be sure that we have got both interrupts before we complete the URB + we have these to flags that shows which part that has completed. + We can then check when we get one of the interrupts that if the other has + occured it's safe for us to complete the URB, otherwise we set appropriate + flag and do the completion when we get the other interrupt. */ + volatile unsigned char ctrl_zout_done; + volatile unsigned char ctrl_rx_done; + + /* Connection between the submitted urb and ETRAX epid number */ + __u8 epid; + + /* The rx_data_list field is used for periodic traffic, to hold + received data for later processing in the the complete_urb functions, + where the data us copied to the urb's transfer_buffer. Basically, we + use this intermediate storage because we don't know when it's safe to + reuse the transfer_buffer (FIXME?). */ + struct list_head rx_data_list; + + + /* The interval time rounded up to closest 2^N */ + int interval; + + /* Pool of EP descriptors needed if it's a INTR transfer. + Amount of EPs in pool correspons to how many INTR that should + be inserted in TxIntrEPList (max 128, defined by MAX_INTR_INTERVAL) */ + struct USB_EP_Desc* intr_ep_pool[128]; + + /* The mount of EPs allocated for this INTR URB */ + int intr_ep_pool_length; + + /* Pointer to info struct if URB is scheduled to be finished later */ + struct urb_later_data* later_data; + + /* Allocated bandwidth for isochronous and interrupt traffic */ + int bandwidth; +}; + + +/* This struct is for passing data from the top half to the bottom half irq + handlers */ +struct crisv10_irq_reg { + struct usb_hcd* hcd; + __u32 r_usb_epid_attn; + __u8 r_usb_status; + __u16 r_usb_rh_port_status_1; + __u16 r_usb_rh_port_status_2; + __u32 r_usb_irq_mask_read; + __u32 r_usb_fm_number; + struct work_struct usb_bh; +}; + + +/* This struct is for passing data from the isoc top half to the isoc bottom + half. */ +struct crisv10_isoc_complete_data { + struct usb_hcd *hcd; + struct urb *urb; + struct work_struct usb_bh; +}; + +/* Entry item for URB lists for each endpint */ +typedef struct urb_entry +{ + struct urb *urb; + struct list_head list; +} urb_entry_t; + +/* --------------------------------------------------------------------------- + Virtual Root HUB + ------------------------------------------------------------------------- */ +/* destination of request */ +#define RH_INTERFACE 0x01 +#define RH_ENDPOINT 0x02 +#define RH_OTHER 0x03 + +#define RH_CLASS 0x20 +#define RH_VENDOR 0x40 + +/* Requests: bRequest << 8 | bmRequestType */ +#define RH_GET_STATUS 0x0080 +#define RH_CLEAR_FEATURE 0x0100 +#define RH_SET_FEATURE 0x0300 +#define RH_SET_ADDRESS 0x0500 +#define RH_GET_DESCRIPTOR 0x0680 +#define RH_SET_DESCRIPTOR 0x0700 +#define RH_GET_CONFIGURATION 0x0880 +#define RH_SET_CONFIGURATION 0x0900 +#define RH_GET_STATE 0x0280 +#define RH_GET_INTERFACE 0x0A80 +#define RH_SET_INTERFACE 0x0B00 +#define RH_SYNC_FRAME 0x0C80 +/* Our Vendor Specific Request */ +#define RH_SET_EP 0x2000 + + +/* Hub port features */ +#define RH_PORT_CONNECTION 0x00 +#define RH_PORT_ENABLE 0x01 +#define RH_PORT_SUSPEND 0x02 +#define RH_PORT_OVER_CURRENT 0x03 +#define RH_PORT_RESET 0x04 +#define RH_PORT_POWER 0x08 +#define RH_PORT_LOW_SPEED 0x09 +#define RH_C_PORT_CONNECTION 0x10 +#define RH_C_PORT_ENABLE 0x11 +#define RH_C_PORT_SUSPEND 0x12 +#define RH_C_PORT_OVER_CURRENT 0x13 +#define RH_C_PORT_RESET 0x14 + +/* Hub features */ +#define RH_C_HUB_LOCAL_POWER 0x00 +#define RH_C_HUB_OVER_CURRENT 0x01 + +#define RH_DEVICE_REMOTE_WAKEUP 0x00 +#define RH_ENDPOINT_STALL 0x01 + +/* Our Vendor Specific feature */ +#define RH_REMOVE_EP 0x00 + + +#define RH_ACK 0x01 +#define RH_REQ_ERR -1 +#define RH_NACK 0x00 + +/* Field definitions for */ + +#define USB_IN_command__eol__BITNR 0 /* command macros */ +#define USB_IN_command__eol__WIDTH 1 +#define USB_IN_command__eol__no 0 +#define USB_IN_command__eol__yes 1 + +#define USB_IN_command__intr__BITNR 3 +#define USB_IN_command__intr__WIDTH 1 +#define USB_IN_command__intr__no 0 +#define USB_IN_command__intr__yes 1 + +#define USB_IN_status__eop__BITNR 1 /* status macros. */ +#define USB_IN_status__eop__WIDTH 1 +#define USB_IN_status__eop__no 0 +#define USB_IN_status__eop__yes 1 + +#define USB_IN_status__eot__BITNR 5 +#define USB_IN_status__eot__WIDTH 1 +#define USB_IN_status__eot__no 0 +#define USB_IN_status__eot__yes 1 + +#define USB_IN_status__error__BITNR 6 +#define USB_IN_status__error__WIDTH 1 +#define USB_IN_status__error__no 0 +#define USB_IN_status__error__yes 1 + +#define USB_IN_status__nodata__BITNR 7 +#define USB_IN_status__nodata__WIDTH 1 +#define USB_IN_status__nodata__no 0 +#define USB_IN_status__nodata__yes 1 + +#define USB_IN_status__epid__BITNR 8 +#define USB_IN_status__epid__WIDTH 5 + +#define USB_EP_command__eol__BITNR 0 +#define USB_EP_command__eol__WIDTH 1 +#define USB_EP_command__eol__no 0 +#define USB_EP_command__eol__yes 1 + +#define USB_EP_command__eof__BITNR 1 +#define USB_EP_command__eof__WIDTH 1 +#define USB_EP_command__eof__no 0 +#define USB_EP_command__eof__yes 1 + +#define USB_EP_command__intr__BITNR 3 +#define USB_EP_command__intr__WIDTH 1 +#define USB_EP_command__intr__no 0 +#define USB_EP_command__intr__yes 1 + +#define USB_EP_command__enable__BITNR 4 +#define USB_EP_command__enable__WIDTH 1 +#define USB_EP_command__enable__no 0 +#define USB_EP_command__enable__yes 1 + +#define USB_EP_command__hw_valid__BITNR 5 +#define USB_EP_command__hw_valid__WIDTH 1 +#define USB_EP_command__hw_valid__no 0 +#define USB_EP_command__hw_valid__yes 1 + +#define USB_EP_command__epid__BITNR 8 +#define USB_EP_command__epid__WIDTH 5 + +#define USB_SB_command__eol__BITNR 0 /* command macros. */ +#define USB_SB_command__eol__WIDTH 1 +#define USB_SB_command__eol__no 0 +#define USB_SB_command__eol__yes 1 + +#define USB_SB_command__eot__BITNR 1 +#define USB_SB_command__eot__WIDTH 1 +#define USB_SB_command__eot__no 0 +#define USB_SB_command__eot__yes 1 + +#define USB_SB_command__intr__BITNR 3 +#define USB_SB_command__intr__WIDTH 1 +#define USB_SB_command__intr__no 0 +#define USB_SB_command__intr__yes 1 + +#define USB_SB_command__tt__BITNR 4 +#define USB_SB_command__tt__WIDTH 2 +#define USB_SB_command__tt__zout 0 +#define USB_SB_command__tt__in 1 +#define USB_SB_command__tt__out 2 +#define USB_SB_command__tt__setup 3 + + +#define USB_SB_command__rem__BITNR 8 +#define USB_SB_command__rem__WIDTH 6 + +#define USB_SB_command__full__BITNR 6 +#define USB_SB_command__full__WIDTH 1 +#define USB_SB_command__full__no 0 +#define USB_SB_command__full__yes 1 + +#endif |