[ramips] add Ralink V11ST-FE board support

This board is equipped with:
- 4MB of NOR Flash
- 32MB of SDRAM
- IC+ IP175C switch
- one Mini-PCI slot

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30561 3c298f89-4303-0410-b956-a3cf2f4a3e73

4 files changed, 14 insertions, 0 deletions

diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 262160490e..b167c520bd 100755
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -69,6 +69,9 @@ get_status_led() {
 	rt-n56u)
 		status_led="asus:blue:power"
 		;;
+	v11st-fe)
+		status_led="v11st-fe:green:status"
+		;;
 	v22rw-2x2)
 		status_led="v22rw-2x2:green:security"
 		;;
diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index 65b2cd39c8..5e6fa420d7 100644
--- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -58,6 +58,7 @@ case "$FIRMWARE" in
 	nw718 | \
 	omni-emb | \
 	rt-n15 | \
+	v11st-fe | \
 	v22rw-2x2 | \
 	w502u | \
 	wcr-150gn | \
diff --git a/target/linux/ramips/base-files/etc/uci-defaults/leds b/target/linux/ramips/base-files/etc/uci-defaults/leds
index bcd17f9d04..891a1a7b3c 100755
--- a/target/linux/ramips/base-files/etc/uci-defaults/leds
+++ b/target/linux/ramips/base-files/etc/uci-defaults/leds
@@ -60,6 +60,9 @@ case $board in
 	nw718)
 		set_usb_led "nw718:amber:usb"
 		;;
+	v11st-fe)
+		set_wifi_led "rt2800pci-phy0::radio"
+		;;
 	w502u)
 		set_usb_led "alfa:blue:usb"
 		set_wifi_led "rt2800pci-phy0::radio"
diff --git a/target/linux/ramips/base-files/etc/uci-defaults/network b/target/linux/ramips/base-files/etc/uci-defaults/network
index 0f97bc3647..a36341ca15 100755
--- a/target/linux/ramips/base-files/etc/uci-defaults/network
+++ b/target/linux/ramips/base-files/etc/uci-defaults/network
@@ -50,6 +50,13 @@ ramips_setup_interfaces()
 		ucidef_add_switch_vlan "switch0" "2" "4 8t"
 		;;
 
+	v11st-fe)
+		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+		ucidef_add_switch "switch0" "1" "1"
+		ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 5t"
+		ucidef_add_switch_vlan "switch0" "2" "0 5t"
+		;;
+
 	wcr-150gn)
 		ucidef_set_interface_lan_wan "eth0.2" "eth0.1"
 		;;