amazon: update amazon target to kernel 3.3

This is just compile tested, my device is currently not working.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31706 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 1493 insertions, 0 deletions

diff --git a/target/linux/amazon/files/drivers/net/ethernet/admmod.c b/target/linux/amazon/files/drivers/net/ethernet/admmod.c
new file mode 100644
index 0000000000..a11ee1d393
--- /dev/null
+++ b/target/linux/amazon/files/drivers/net/ethernet/admmod.c
@@ -0,0 +1,1493 @@
+/******************************************************************************
+     Copyright (c) 2004, Infineon Technologies.  All rights reserved.
+
+                               No Warranty
+   Because the program is licensed free of charge, there is no warranty for
+   the program, to the extent permitted by applicable law.  Except when
+   otherwise stated in writing the copyright holders and/or other parties
+   provide the program "as is" without warranty of any kind, either
+   expressed or implied, including, but not limited to, the implied
+   warranties of merchantability and fitness for a particular purpose. The
+   entire risk as to the quality and performance of the program is with
+   you.  should the program prove defective, you assume the cost of all
+   necessary servicing, repair or correction.
+
+   In no event unless required by applicable law or agreed to in writing
+   will any copyright holder, or any other party who may modify and/or
+   redistribute the program as permitted above, be liable to you for
+   damages, including any general, special, incidental or consequential
+   damages arising out of the use or inability to use the program
+   (including but not limited to loss of data or data being rendered
+   inaccurate or losses sustained by you or third parties or a failure of
+   the program to operate with any other programs), even if such holder or
+   other party has been advised of the possibility of such damages.
+ ******************************************************************************
+   Module      : admmod.c
+   Date        : 2004-09-01
+   Description : JoeLin
+   Remarks:
+
+   Revision:
+	MarsLin, add to support VLAN
+
+ *****************************************************************************/
+//000001.joelin 2005/06/02 add"ADM6996_MDC_MDIO_MODE" define, 
+//		if define ADM6996_MDC_MDIO_MODE==> ADM6996LC and ADM6996I will be in MDIO/MDC(SMI)(16 bit) mode,
+//		amazon should contrl ADM6996 by MDC/MDIO pin
+//  		if undef ADM6996_MDC_MDIO_MODE==> ADM6996  will be in EEProm(32 bit) mode,
+//		amazon should contrl ADM6996 by GPIO15,16,17,18  pin
+/* 507281:linmars 2005/07/28 support MDIO/EEPROM config mode */
+/* 509201:linmars remove driver testing codes */
+
+#include <linux/version.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/proc_fs.h>
+#include <linux/delay.h>
+#include <asm/uaccess.h>
+#include <linux/init.h>
+#include <linux/ioctl.h>
+#include <asm/atomic.h>
+#include <asm-mips/amazon/amazon.h>
+#include <asm-mips/amazon/adm6996.h>
+//#include <linux/amazon/adm6996.h>
+
+
+unsigned int ifx_sw_conf[ADM_SW_MAX_PORT_NUM+1] = \
+	{ADM_SW_PORT0_CONF, ADM_SW_PORT1_CONF, ADM_SW_PORT2_CONF, \
+	ADM_SW_PORT3_CONF, ADM_SW_PORT4_CONF, ADM_SW_PORT5_CONF};
+unsigned int ifx_sw_bits[8] = \
+	{0x1, 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff};
+unsigned int ifx_sw_vlan_port[6] = {0, 2, 4, 6, 7, 8};
+//050613:fchang 
+/* 507281:linmars start */
+#ifdef CONFIG_SWITCH_ADM6996_MDIO
+#define ADM6996_MDC_MDIO_MODE 1 //000001.joelin
+#else
+#undef ADM6996_MDC_MDIO_MODE
+#endif
+/* 507281:linmars end */
+#define adm6996i 0
+#define adm6996lc 1
+#define adm6996l  2
+unsigned int adm6996_mode=adm6996i;
+/*
+  initialize GPIO pins.
+  output mode, low
+*/
+void ifx_gpio_init(void)
+{
+ //GPIO16,17,18 direction:output
+ //GPIO16,17,18 output 0
+ 
+    AMAZON_SW_REG(AMAZON_GPIO_P1_DIR) |= (GPIO_MDIO|GPIO_MDCS|GPIO_MDC);
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT) =AMAZON_SW_REG(AMAZON_GPIO_P1_IN)& ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC);
+
+}
+
+/* read one bit from mdio port */
+int ifx_sw_mdio_readbit(void)
+{
+    //int val;
+
+    //val = (AMAZON_SW_REG(GPIO_conf0_REG) & GPIO0_INPUT_MASK) >> 8;
+    //return val;
+    //GPIO16
+    return AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&1;
+}
+
+/*
+  MDIO mode selection
+  1 -> output
+  0 -> input
+
+  switch input/output mode of GPIO 0
+*/
+void ifx_mdio_mode(int mode)
+{
+//    AMAZON_SW_REG(GPIO_conf0_REG) = mode ? GPIO_ENABLEBITS :
+//                             ((GPIO_ENABLEBITS | MDIO_INPUT) & ~MDIO_OUTPUT_EN);
+    mode?(AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)|=GPIO_MDIO):
+         (AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)&=~GPIO_MDIO);
+    /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_DIR);
+    mode?(r|=GPIO_MDIO):(r&=~GPIO_MDIO);
+    AMAZON_SW_REG(AMAZON_GPIO_P1_DIR)=r;*/
+}
+
+void ifx_mdc_hi(void)
+{
+    //GPIO_SET_HI(GPIO_MDC);
+    //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDC;
+    /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT);
+    r|=GPIO_MDC;
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/
+
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDC;
+}
+
+void ifx_mdio_hi(void)
+{
+    //GPIO_SET_HI(GPIO_MDIO);
+    //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDIO;
+    /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT);
+    r|=GPIO_MDIO;
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/
+
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDIO;
+}
+
+void ifx_mdcs_hi(void)
+{
+    //GPIO_SET_HI(GPIO_MDCS);
+    //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)|=GPIO_MDCS;
+    /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT);
+    r|=GPIO_MDCS;
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/
+
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)|GPIO_MDCS;
+}
+
+void ifx_mdc_lo(void)
+{
+    //GPIO_SET_LOW(GPIO_MDC);
+    //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDC;
+    /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT);
+    r&=~GPIO_MDC;
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/
+
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDC);
+}
+
+void ifx_mdio_lo(void)
+{
+    //GPIO_SET_LOW(GPIO_MDIO);
+    //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDIO;
+    /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT);
+    r&=~GPIO_MDIO;
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/
+
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDIO);
+}
+
+void ifx_mdcs_lo(void)
+{
+    //GPIO_SET_LOW(GPIO_MDCS);
+    //AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)&=~GPIO_MDCS;
+    /*int r=AMAZON_SW_REG(AMAZON_GPIO_P1_OUT);
+    r&=~GPIO_MDCS;
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=r;*/
+    
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OUT)=AMAZON_SW_REG(AMAZON_GPIO_P1_IN)&(~GPIO_MDCS);
+}
+
+/*
+  mdc pulse
+  0 -> 1 -> 0
+*/
+static void ifx_sw_mdc_pulse(void)
+{
+    ifx_mdc_lo();
+    udelay(ADM_SW_MDC_DOWN_DELAY);
+    ifx_mdc_hi();
+    udelay(ADM_SW_MDC_UP_DELAY);
+    ifx_mdc_lo();
+}
+
+/*
+  mdc toggle
+  1 -> 0
+*/
+static void ifx_sw_mdc_toggle(void)
+{
+    ifx_mdc_hi();
+    udelay(ADM_SW_MDC_UP_DELAY);
+    ifx_mdc_lo();
+    udelay(ADM_SW_MDC_DOWN_DELAY);
+}
+
+/*
+  enable eeprom write
+  For ATC 93C66 type EEPROM; accessing ADM6996 internal EEPROM type registers
+*/
+static void ifx_sw_eeprom_write_enable(void)
+{
+    unsigned int op;
+
+    ifx_mdcs_lo();
+    ifx_mdc_lo();
+    ifx_mdio_hi();
+    udelay(ADM_SW_CS_DELAY);
+    /* enable chip select */
+    ifx_mdcs_hi();
+    udelay(ADM_SW_CS_DELAY);
+    /* start bit */
+    ifx_mdio_hi();
+    ifx_sw_mdc_pulse();
+
+    /* eeprom write enable */
+    op = ADM_SW_BIT_MASK_4;
+    while (op)
+    {
+        if (op & ADM_SW_EEPROM_WRITE_ENABLE)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 3);
+    while (op)
+    {
+        ifx_mdio_lo();
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+    /* disable chip select */
+    ifx_mdcs_lo();
+    udelay(ADM_SW_CS_DELAY);
+    ifx_sw_mdc_pulse();
+}
+
+/*
+  disable eeprom write
+*/
+static void ifx_sw_eeprom_write_disable(void)
+{
+    unsigned int op;
+
+    ifx_mdcs_lo();
+    ifx_mdc_lo();
+    ifx_mdio_hi();
+    udelay(ADM_SW_CS_DELAY);
+    /* enable chip select */
+    ifx_mdcs_hi();
+    udelay(ADM_SW_CS_DELAY);
+
+    /* start bit */
+    ifx_mdio_hi();
+    ifx_sw_mdc_pulse();
+    /* eeprom write disable */
+    op = ADM_SW_BIT_MASK_4;
+    while (op)
+    {
+        if (op & ADM_SW_EEPROM_WRITE_DISABLE)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 3);
+    while (op)
+    {
+        ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+    /* disable chip select */
+    ifx_mdcs_lo();
+    udelay(ADM_SW_CS_DELAY);
+    ifx_sw_mdc_pulse();
+}
+
+/*
+  read registers from ADM6996
+  serial registers start at 0x200 (addr bit 9 = 1b)
+  EEPROM registers -> 16bits; Serial registers -> 32bits
+*/
+#ifdef ADM6996_MDC_MDIO_MODE //smi mode//000001.joelin
+static int ifx_sw_read_adm6996i_smi(unsigned int addr, unsigned int *dat)
+{
+   addr=(addr<<16)&0x3ff0000;
+   AMAZON_SW_REG(AMAZON_SW_MDIO_ACC) =(0xC0000000|addr);
+   while ((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x80000000){};
+   *dat=((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x0FFFF);
+    return 0;
+}
+#endif
+
+static int ifx_sw_read_adm6996i(unsigned int addr, unsigned int *dat)
+{
+    unsigned int op;
+
+    ifx_gpio_init();
+
+    ifx_mdcs_hi();
+    udelay(ADM_SW_CS_DELAY);
+
+    ifx_mdcs_lo();
+    ifx_mdc_lo();
+    ifx_mdio_lo();
+
+    udelay(ADM_SW_CS_DELAY);
+
+    /* preamble, 32 bit 1 */
+    ifx_mdio_hi();
+    op = ADM_SW_BIT_MASK_32;
+    while (op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* command start (01b) */
+    op = ADM_SW_BIT_MASK_2;
+    while (op)
+    {
+        if (op & ADM_SW_SMI_START)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* read command (10b) */
+    op = ADM_SW_BIT_MASK_2;
+    while (op)
+    {
+        if (op & ADM_SW_SMI_READ)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* send address A9 ~ A0 */
+    op = ADM_SW_BIT_MASK_10;
+    while (op)
+    {
+        if (op & addr)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* turnaround bits */
+    op = ADM_SW_BIT_MASK_2;
+    ifx_mdio_hi();
+    while (op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    udelay(ADM_SW_MDC_DOWN_DELAY);
+
+    /* set MDIO pin to input mode */
+    ifx_mdio_mode(ADM_SW_MDIO_INPUT);
+
+    /* start read data */
+    *dat = 0;
+//adm6996i    op = ADM_SW_BIT_MASK_32;
+    op = ADM_SW_BIT_MASK_16;//adm6996i
+    while (op)
+    {
+        *dat <<= 1;
+        if (ifx_sw_mdio_readbit()) *dat |= 1;
+        ifx_sw_mdc_toggle();
+
+        op >>= 1;
+    }
+
+    /* set MDIO to output mode */
+    ifx_mdio_mode(ADM_SW_MDIO_OUTPUT);
+
+    /* dummy clock */
+    op = ADM_SW_BIT_MASK_4;
+    ifx_mdio_lo();
+    while(op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    ifx_mdc_lo();
+    ifx_mdio_lo();
+    ifx_mdcs_hi();
+
+    /* EEPROM registers */
+//adm6996i    if (!(addr & 0x200))
+//adm6996i    {
+//adm6996i        if (addr % 2)
+//adm6996i            *dat >>= 16;
+//adm6996i        else
+//adm6996i        *dat &= 0xffff;
+//adm6996i    }
+
+    return 0;
+}
+//adm6996
+static int ifx_sw_read_adm6996l(unsigned int addr, unsigned int *dat)
+{
+    unsigned int op;
+
+    ifx_gpio_init();
+
+    ifx_mdcs_hi();
+    udelay(ADM_SW_CS_DELAY);
+
+    ifx_mdcs_lo();
+    ifx_mdc_lo();
+    ifx_mdio_lo();
+
+    udelay(ADM_SW_CS_DELAY);
+
+    /* preamble, 32 bit 1 */
+    ifx_mdio_hi();
+    op = ADM_SW_BIT_MASK_32;
+    while (op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* command start (01b) */
+    op = ADM_SW_BIT_MASK_2;
+    while (op)
+    {
+        if (op & ADM_SW_SMI_START)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* read command (10b) */
+    op = ADM_SW_BIT_MASK_2;
+    while (op)
+    {
+        if (op & ADM_SW_SMI_READ)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* send address A9 ~ A0 */
+    op = ADM_SW_BIT_MASK_10;
+    while (op)
+    {
+        if (op & addr)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* turnaround bits */
+    op = ADM_SW_BIT_MASK_2;
+    ifx_mdio_hi();
+    while (op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    udelay(ADM_SW_MDC_DOWN_DELAY);
+
+    /* set MDIO pin to input mode */
+    ifx_mdio_mode(ADM_SW_MDIO_INPUT);
+
+    /* start read data */
+    *dat = 0;
+    op = ADM_SW_BIT_MASK_32;
+    while (op)
+    {
+        *dat <<= 1;
+        if (ifx_sw_mdio_readbit()) *dat |= 1;
+        ifx_sw_mdc_toggle();
+
+        op >>= 1;
+    }
+
+    /* set MDIO to output mode */
+    ifx_mdio_mode(ADM_SW_MDIO_OUTPUT);
+
+    /* dummy clock */
+    op = ADM_SW_BIT_MASK_4;
+    ifx_mdio_lo();
+    while(op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    ifx_mdc_lo();
+    ifx_mdio_lo();
+    ifx_mdcs_hi();
+
+    /* EEPROM registers */
+    if (!(addr & 0x200))
+    {
+        if (addr % 2)
+            *dat >>= 16;
+        else
+        *dat &= 0xffff;
+    }
+
+    return 0;
+}
+
+static int ifx_sw_read(unsigned int addr, unsigned int *dat)
+{
+#ifdef ADM6996_MDC_MDIO_MODE //smi mode ////000001.joelin
+	ifx_sw_read_adm6996i_smi(addr,dat);
+#else	
+	if (adm6996_mode==adm6996i) ifx_sw_read_adm6996i(addr,dat);
+		else ifx_sw_read_adm6996l(addr,dat);
+#endif		
+	return 0;
+	
+}
+
+/*
+  write register to ADM6996 eeprom registers
+*/
+//for adm6996i -start
+#ifdef ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin
+static int ifx_sw_write_adm6996i_smi(unsigned int addr, unsigned int dat)
+{
+ 
+   AMAZON_SW_REG(AMAZON_SW_MDIO_ACC) = ((addr<<16)&0x3ff0000)|dat|0x80000000;
+   while ((AMAZON_SW_REG(AMAZON_SW_MDIO_ACC))&0x80000000){};
+  
+    return 0;
+ 
+}
+#endif //ADM6996_MDC_MDIO_MODE //000001.joelin
+
+static int ifx_sw_write_adm6996i(unsigned int addr, unsigned int dat)
+{
+    unsigned int op;
+
+    ifx_gpio_init();
+
+    ifx_mdcs_hi();
+    udelay(ADM_SW_CS_DELAY);
+
+    ifx_mdcs_lo();
+    ifx_mdc_lo();
+    ifx_mdio_lo();
+
+    udelay(ADM_SW_CS_DELAY);
+
+    /* preamble, 32 bit 1 */
+    ifx_mdio_hi();
+    op = ADM_SW_BIT_MASK_32;
+    while (op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* command start (01b) */
+    op = ADM_SW_BIT_MASK_2;
+    while (op)
+    {
+        if (op & ADM_SW_SMI_START)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* write command (01b) */
+    op = ADM_SW_BIT_MASK_2;
+    while (op)
+    {
+        if (op & ADM_SW_SMI_WRITE)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* send address A9 ~ A0 */
+    op = ADM_SW_BIT_MASK_10;
+    while (op)
+    {
+        if (op & addr)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* turnaround bits */
+    op = ADM_SW_BIT_MASK_2;
+    ifx_mdio_hi();
+    while (op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    udelay(ADM_SW_MDC_DOWN_DELAY);
+
+    /* set MDIO pin to output mode */
+    ifx_mdio_mode(ADM_SW_MDIO_OUTPUT);
+
+  
+    /* start write data */
+    op = ADM_SW_BIT_MASK_16;
+    while (op)
+    {
+        if (op & dat)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_toggle();
+        op >>= 1;
+    }
+
+ //   /* set MDIO to output mode */
+ //   ifx_mdio_mode(ADM_SW_MDIO_OUTPUT);
+
+    /* dummy clock */
+    op = ADM_SW_BIT_MASK_4;
+    ifx_mdio_lo();
+    while(op)
+    {
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    ifx_mdc_lo();
+    ifx_mdio_lo();
+    ifx_mdcs_hi();
+
+    /* EEPROM registers */
+//adm6996i    if (!(addr & 0x200))
+//adm6996i    {
+//adm6996i        if (addr % 2)
+//adm6996i            *dat >>= 16;
+//adm6996i        else
+//adm6996i        *dat &= 0xffff;
+//adm6996i    }
+
+    return 0;
+}
+//for adm6996i-end
+static int ifx_sw_write_adm6996l(unsigned int addr, unsigned int dat)
+{
+    unsigned int op;
+
+    ifx_gpio_init();
+
+    /* enable write */
+    ifx_sw_eeprom_write_enable();
+
+    /* chip select */
+    ifx_mdcs_hi();
+    udelay(ADM_SW_CS_DELAY);
+
+    /* issue write command */
+    /* start bit */
+    ifx_mdio_hi();
+    ifx_sw_mdc_pulse();
+
+    /* EEPROM write command */
+    op = ADM_SW_BIT_MASK_2;
+    while (op)
+    {
+        if (op & ADM_SW_EEPROM_WRITE)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_pulse();
+        op >>= 1;
+    }
+
+    /* send address A7 ~ A0 */
+    op = ADM_SW_BIT_MASK_1 << (EEPROM_TYPE - 1);
+
+    while (op)
+    {
+        if (op & addr)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_toggle();
+        op >>= 1;
+    }
+
+    /* start write data */
+    op = ADM_SW_BIT_MASK_16;
+    while (op)
+    {
+        if (op & dat)
+            ifx_mdio_hi();
+        else
+            ifx_mdio_lo();
+
+        ifx_sw_mdc_toggle();
+        op >>= 1;
+    }
+
+    /* disable cs & wait 1 clock */
+    ifx_mdcs_lo();
+    udelay(ADM_SW_CS_DELAY);
+    ifx_sw_mdc_toggle();
+
+    ifx_sw_eeprom_write_disable();
+
+    return 0;
+}
+
+static int ifx_sw_write(unsigned int addr, unsigned int dat)
+{
+#ifdef ADM6996_MDC_MDIO_MODE //smi mode ////000001.joelin
+	ifx_sw_write_adm6996i_smi(addr,dat);
+#else	//000001.joelin
+	if (adm6996_mode==adm6996i) ifx_sw_write_adm6996i(addr,dat);
+		else ifx_sw_write_adm6996l(addr,dat);
+#endif	//000001.joelin
+	return 0;
+}
+
+/*
+  do switch PHY reset
+*/
+int ifx_sw_reset(void)
+{
+    /* reset PHY */
+    ifx_sw_write(ADM_SW_PHY_RESET, 0);
+
+    return 0;
+}
+
+/* 509201:linmars start */
+#if 0
+/*
+  check port status
+*/
+int ifx_check_port_status(int port)
+{
+    unsigned int val;
+
+    if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM))
+    {
+        ifx_printf(("error on port number (%d)!!\n", port));
+        return -1;
+    }
+
+    ifx_sw_read(ifx_sw_conf[port], &val);
+    if (ifx_sw_conf[port]%2) val >>= 16;
+    /* only 16bits are effective */
+    val &= 0xFFFF;
+
+    ifx_printf(("Port %d status (%.8x): \n", port, val));
+
+    if (val & ADM_SW_PORT_FLOWCTL)
+        ifx_printf(("\t802.3x flow control supported!\n"));
+    else
+        ifx_printf(("\t802.3x flow control not supported!\n"));
+
+    if (val & ADM_SW_PORT_AN)
+        ifx_printf(("\tAuto negotiation ON!\n"));
+    else
+        ifx_printf(("\tAuto negotiation OFF!\n"));
+
+    if (val & ADM_SW_PORT_100M)
+        ifx_printf(("\tLink at 100M!\n"));
+    else
+        ifx_printf(("\tLink at 10M!\n"));
+
+    if (val & ADM_SW_PORT_FULL)
+        ifx_printf(("\tFull duplex!\n"));
+    else
+        ifx_printf(("\tHalf duplex!\n"));
+
+    if (val & ADM_SW_PORT_DISABLE)
+        ifx_printf(("\tPort disabled!\n"));
+    else
+        ifx_printf(("\tPort enabled!\n"));
+
+    if (val & ADM_SW_PORT_TOS)
+        ifx_printf(("\tTOS enabled!\n"));
+    else
+        ifx_printf(("\tTOS disabled!\n"));
+
+    if (val & ADM_SW_PORT_PPRI)
+        ifx_printf(("\tPort priority first!\n"));
+    else
+        ifx_printf(("\tVLAN or TOS priority first!\n"));
+
+    if (val & ADM_SW_PORT_MDIX)
+        ifx_printf(("\tAuto MDIX!\n"));
+    else
+        ifx_printf(("\tNo auto MDIX\n"));
+
+    ifx_printf(("\tPVID: %d\n", \
+  	    ((val >> ADM_SW_PORT_PVID_SHIFT)&ifx_sw_bits[ADM_SW_PORT_PVID_BITS])));
+
+    return 0;
+}
+/*
+  initialize a VLAN
+  clear all VLAN bits
+*/
+int ifx_sw_vlan_init(int vlanid)
+{
+    ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, 0);
+
+    return 0;
+}
+
+/*
+  add a port to certain vlan
+*/
+int ifx_sw_vlan_add(int port, int vlanid)
+{
+    int reg = 0;
+
+    if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM) || (vlanid < 0) ||
+        (vlanid > ADM_SW_MAX_VLAN_NUM))
+    {
+        ifx_printf(("Port number or VLAN number ERROR!!\n"));
+        return -1;
+    }
+    ifx_sw_read(ADM_SW_VLAN0_CONF + vlanid, &reg);
+    reg |= (1 << ifx_sw_vlan_port[port]);
+    ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, reg);
+
+    return 0;
+}
+
+/*
+  delete a given port from certain vlan
+*/
+int ifx_sw_vlan_del(int port, int vlanid)
+{
+    unsigned int reg = 0;
+
+    if ((port < 0) || (port > ADM_SW_MAX_PORT_NUM) || (vlanid < 0) || (vlanid > ADM_SW_MAX_VLAN_NUM))
+    {
+        ifx_printf(("Port number or VLAN number ERROR!!\n"));
+        return -1;
+    }
+    ifx_sw_read(ADM_SW_VLAN0_CONF + vlanid, &reg);
+    reg &= ~(1 << ifx_sw_vlan_port[port]);
+    ifx_sw_write(ADM_SW_VLAN0_CONF + vlanid, reg);
+
+    return 0;
+}
+
+/*
+  default VLAN setting
+
+  port 0~3 as untag port and PVID = 1
+  VLAN1: port 0~3 and port 5 (MII)
+*/
+static int ifx_sw_init(void)
+{
+    ifx_printf(("Setting default ADM6996 registers... \n"));
+
+    /* MAC clone, 802.1q based VLAN */
+    ifx_sw_write(ADM_SW_VLAN_MODE, 0xff30);
+    /* auto MDIX, PVID=1, untag */
+    ifx_sw_write(ADM_SW_PORT0_CONF, 0x840f);
+    ifx_sw_write(ADM_SW_PORT1_CONF, 0x840f);
+    ifx_sw_write(ADM_SW_PORT2_CONF, 0x840f);
+    ifx_sw_write(ADM_SW_PORT3_CONF, 0x840f);
+    /* auto MDIX, PVID=2, untag */
+    ifx_sw_write(ADM_SW_PORT5_CONF, 0x880f);
+    /* port 0~3 & 5 as VLAN1 */
+    ifx_sw_write(ADM_SW_VLAN0_CONF+1, 0x0155);
+
+    return 0;
+}
+#endif
+/* 509201:linmars end */
+
+int adm_open(struct inode *node, struct file *filp)
+{
+    return 0;
+}
+
+ssize_t adm_read(struct file *filep, char *buf, size_t count, loff_t *ppos)
+{
+    return count;
+}
+
+ssize_t adm_write(struct file *filep, const char *buf, size_t count, loff_t *ppos)
+{
+    return count;
+}
+
+/* close */
+int adm_release(struct inode *inode, struct file *filp)
+{
+    return 0;
+}
+
+/* IOCTL function */
+
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,36))
+static long adm_ioctl(struct file *filp, unsigned int cmd, unsigned long args)
+#else
+static int adm_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long args)
+#endif
+{
+    PREGRW uREGRW;
+    unsigned int rtval;
+    unsigned int val;		//6996i
+    unsigned int control[6] ;	//6996i
+    unsigned int status[6] ;	//6996i
+    
+    PMACENTRY mMACENTRY;//adm6996i
+    PPROTOCOLFILTER uPROTOCOLFILTER ;///adm6996i
+
+    if (_IOC_TYPE(cmd) != ADM_MAGIC)
+    {
+        printk("adm_ioctl: IOC_TYPE(%x) != ADM_MAGIC(%x)! \n", _IOC_TYPE(cmd), ADM_MAGIC);
+        return (-EINVAL);
+    }
+
+    if(_IOC_NR(cmd) >= KEY_IOCTL_MAX_KEY)
+    {
+        printk(KERN_WARNING "adm_ioctl: IOC_NR(%x) invalid! \n", _IOC_NR(cmd));
+        return (-EINVAL);
+    }
+
+    switch (cmd)
+    {
+        case ADM_IOCTL_REGRW:
+        {
+            uREGRW = (PREGRW)kmalloc(sizeof(REGRW), GFP_KERNEL);
+            rtval = copy_from_user(uREGRW, (PREGRW)args, sizeof(REGRW));
+            if (rtval != 0)
+            {
+                printk("ADM_IOCTL_REGRW: copy from user FAILED!! \n");
+                return (-EFAULT);
+            }
+
+            switch(uREGRW->mode)
+            {
+                case REG_READ:
+                    uREGRW->value = 0x12345678;//inl(uREGRW->addr);
+                    copy_to_user((PREGRW)args, uREGRW, sizeof(REGRW));
+                    break;
+                case REG_WRITE:
+                    //outl(uREGRW->value, uREGRW->addr);
+                    break;
+
+                default:
+                    printk("No such Register Read/Write function!! \n");
+                    return (-EFAULT);
+            }
+            kfree(uREGRW);
+            break;
+        }
+
+        case ADM_SW_IOCTL_REGRW:
+        {
+            unsigned int val = 0xff;
+
+            uREGRW = (PREGRW)kmalloc(sizeof(REGRW), GFP_KERNEL);
+            rtval = copy_from_user(uREGRW, (PREGRW)args, sizeof(REGRW));
+            if (rtval != 0)
+            {
+                printk("ADM_IOCTL_REGRW: copy from user FAILED!! \n");
+                return (-EFAULT);
+            }
+
+            switch(uREGRW->mode)
+            {
+                case REG_READ:
+                    ifx_sw_read(uREGRW->addr, &val);
+                    uREGRW->value = val;
+                    copy_to_user((PREGRW)args, uREGRW, sizeof(REGRW));
+                    break;
+
+                case REG_WRITE:
+                    ifx_sw_write(uREGRW->addr, uREGRW->value);
+                    break;
+                default:
+                    printk("No such Register Read/Write function!! \n");
+                    return (-EFAULT);
+            }
+            kfree(uREGRW);
+            break;
+        }
+/* 509201:linmars start */
+#if 0
+        case ADM_SW_IOCTL_PORTSTS:
+            for (rtval = 0; rtval < ADM_SW_MAX_PORT_NUM+1; rtval++)
+                ifx_check_port_status(rtval);
+            break;
+        case ADM_SW_IOCTL_INIT:
+            ifx_sw_init();
+            break;
+#endif
+/* 509201:linmars end */
+//adm6996i
+        case ADM_SW_IOCTL_MACENTRY_ADD:
+        case ADM_SW_IOCTL_MACENTRY_DEL:
+        case ADM_SW_IOCTL_MACENTRY_GET_INIT:
+        case ADM_SW_IOCTL_MACENTRY_GET_MORE:
+                
+
+           mMACENTRY = (PMACENTRY)kmalloc(sizeof(MACENTRY), GFP_KERNEL);
+            rtval = copy_from_user(mMACENTRY, (PMACENTRY)args, sizeof(MACENTRY));
+            if (rtval != 0)
+            {
+                printk("ADM_SW_IOCTL_MACENTRY: copy from user FAILED!! \n");
+                return (-EFAULT);
+            }
+           control[0]=(mMACENTRY->mac_addr[1]<<8)+mMACENTRY->mac_addr[0]     ; 
+           control[1]=(mMACENTRY->mac_addr[3]<<8)+mMACENTRY->mac_addr[2]      ;         
+           control[2]=(mMACENTRY->mac_addr[5]<<8)+mMACENTRY->mac_addr[4]     ;
+           control[3]=(mMACENTRY->fid&0xf)+((mMACENTRY->portmap&0x3f)<<4);
+           if (((mMACENTRY->info_type)&0x01)) control[4]=(mMACENTRY->ctrl.info_ctrl)+0x1000; //static ,info control
+           	else	control[4]=((mMACENTRY->ctrl.age_timer)&0xff);//not static ,agetimer
+         	if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) { 	
+	           //initial  the pointer to the first address	
+			           val=0x8000;//busy ,status5[15]
+			           while(val&0x8000){		//check busy ?
+			 	          ifx_sw_read(0x125, &val);
+			        	}    
+			           control[5]=0x030;//initial the first address	
+			           ifx_sw_write(0x11f,control[5]);
+			        	       	
+			           	
+			           val=0x8000;//busy ,status5[15]
+			           while(val&0x8000){		//check busy ?
+			 	          ifx_sw_read(0x125, &val);
+			        	}           	
+	           	
+	           }	//if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)								
+           if (cmd==ADM_SW_IOCTL_MACENTRY_ADD) control[5]=0x07;//create a new address
+           	else if (cmd==ADM_SW_IOCTL_MACENTRY_DEL) control[5]=0x01f;//erased an existed address
+           	else if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) 
+           		control[5]=0x02c;//search by the mac address field
+           
+           val=0x8000;//busy ,status5[15]
+           while(val&0x8000){		//check busy ?
+ 	          ifx_sw_read(0x125, &val);
+        	}
+        	ifx_sw_write(0x11a,control[0]);	
+        	ifx_sw_write(0x11b,control[1]);	
+        	ifx_sw_write(0x11c,control[2]);	
+        	ifx_sw_write(0x11d,control[3]);	
+        	ifx_sw_write(0x11e,control[4]);	
+        	ifx_sw_write(0x11f,control[5]);	
+           val=0x8000;//busy ,status5[15]
+           while(val&0x8000){		//check busy ?
+ 	          ifx_sw_read(0x125, &val);
+        	}	
+           val=((val&0x7000)>>12);//result ,status5[14:12]
+           mMACENTRY->result=val;
+   
+           if (!val) {
+        		printk(" Command OK!! \n");
+        		if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) {
+			           	ifx_sw_read(0x120,&(status[0]));	
+			        	ifx_sw_read(0x121,&(status[1]));	
+			        	ifx_sw_read(0x122,&(status[2]));	
+			        	ifx_sw_read(0x123,&(status[3]));	
+			        	ifx_sw_read(0x124,&(status[4]));	
+			        	ifx_sw_read(0x125,&(status[5]));	
+		
+		           		
+		        		mMACENTRY->mac_addr[0]=(status[0]&0x00ff)	;
+		        		mMACENTRY->mac_addr[1]=(status[0]&0xff00)>>8    ;
+		        		mMACENTRY->mac_addr[2]=(status[1]&0x00ff)    ;
+		        		mMACENTRY->mac_addr[3]=(status[1]&0xff00)>>8 ;
+		        		mMACENTRY->mac_addr[4]=(status[2]&0x00ff)    ;
+		        		mMACENTRY->mac_addr[5]=(status[2]&0xff00)>>8 ;
+		        		mMACENTRY->fid=(status[3]&0xf);
+		        		mMACENTRY->portmap=((status[3]>>4)&0x3f);
+		        		if (status[5]&0x2) {//static info_ctrl //status5[1]????
+		        			mMACENTRY->ctrl.info_ctrl=(status[4]&0x00ff);
+		  				mMACENTRY->info_type=1;
+		        				}
+		        		else {//not static age_timer
+		        			mMACENTRY->ctrl.age_timer=(status[4]&0x00ff);
+		  				mMACENTRY->info_type=0;
+		        				}
+//status5[13]????					mMACENTRY->occupy=(status[5]&0x02)>>1;//status5[1]
+					mMACENTRY->occupy=(status[5]&0x02000)>>13;//status5[13] ???
+					mMACENTRY->bad=(status[5]&0x04)>>2;//status5[2]
+				}//if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) 
+			
+        	}
+           else if (val==0x001)  
+                printk(" All Entry Used!! \n");
+            else if (val==0x002) 
+                printk("  Entry Not Found!! \n");
+            else if (val==0x003) 
+                printk(" Try Next Entry!! \n");
+            else if (val==0x005)  
+                printk(" Command Error!! \n");   
+            else   
+                printk(" UnKnown Error!! \n");
+                
+            copy_to_user((PMACENTRY)args, mMACENTRY,sizeof(MACENTRY));    
+                
+ 	    break;  
+ 
+        case ADM_SW_IOCTL_FILTER_ADD:
+        case ADM_SW_IOCTL_FILTER_DEL:
+        case ADM_SW_IOCTL_FILTER_GET:
+
+            uPROTOCOLFILTER = (PPROTOCOLFILTER)kmalloc(sizeof(PROTOCOLFILTER), GFP_KERNEL);
+            rtval = copy_from_user(uPROTOCOLFILTER, (PPROTOCOLFILTER)args, sizeof(PROTOCOLFILTER));
+            if (rtval != 0)
+            {
+                printk("ADM_SW_IOCTL_FILTER_ADD: copy from user FAILED!! \n");
+                return (-EFAULT);
+            }
+            
+        	if(cmd==ADM_SW_IOCTL_FILTER_DEL) {	//delete filter
+			uPROTOCOLFILTER->ip_p=00;	//delet filter
+			uPROTOCOLFILTER->action=00;	//delete filter
+		}					//delete filter
+
+            ifx_sw_read(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), &val);//rx68~rx6b,protocol filter0~7	
+
+            	if (((uPROTOCOLFILTER->protocol_filter_num)%2)==00){	
+            		if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= val&0x00ff;//get filter ip_p
+            			else val=(val&0xff00)|(uPROTOCOLFILTER->ip_p);//set filter ip_p
+        	}
+        	else {
+        		if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= (val>>8);//get filter ip_p
+        			else val=(val&0x00ff)|((uPROTOCOLFILTER->ip_p)<<8);//set filter ip_p
+        	}	
+            if(cmd!=ADM_SW_IOCTL_FILTER_GET) ifx_sw_write(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), val);//write rx68~rx6b,protocol filter0~7	
+            		
+            ifx_sw_read(0x95, &val);	//protocol filter action
+            if(cmd==ADM_SW_IOCTL_FILTER_GET) {
+            		uPROTOCOLFILTER->action= ((val>>(uPROTOCOLFILTER->protocol_filter_num*2))&0x3);//get filter action
+            		copy_to_user((PPROTOCOLFILTER)args, uPROTOCOLFILTER, sizeof(PROTOCOLFILTER));
+            	
+            	}
+            	else {
+            		val=(val&(~(0x03<<(uPROTOCOLFILTER->protocol_filter_num*2))))|(((uPROTOCOLFILTER->action)&0x03)<<(uPROTOCOLFILTER->protocol_filter_num*2));
+  //          		printk("%d----\n",val);
+            		ifx_sw_write(0x95, val);	//write protocol filter action		
+            	}
+            	
+            break;
+//adm6996i  
+
+        /* others */
+        default:
+            return -EFAULT;
+    }
+    /* end of switch */
+    return 0;
+}
+
+/* Santosh: handle IGMP protocol filter ADD/DEL/GET */
+int adm_process_protocol_filter_request (unsigned int cmd, PPROTOCOLFILTER uPROTOCOLFILTER)
+{
+    unsigned int val;		//6996i
+
+	if(cmd==ADM_SW_IOCTL_FILTER_DEL) {	//delete filter
+	uPROTOCOLFILTER->ip_p=00;	//delet filter
+	uPROTOCOLFILTER->action=00;	//delete filter
+	}					//delete filter
+
+    ifx_sw_read(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), &val);//rx68~rx6b,protocol filter0~7	
+
+    if (((uPROTOCOLFILTER->protocol_filter_num)%2)==00){	
+    	if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= val&0x00ff;//get filter ip_p
+        else val=(val&0xff00)|(uPROTOCOLFILTER->ip_p);//set filter ip_p
+    }
+    else {
+    	if(cmd==ADM_SW_IOCTL_FILTER_GET) uPROTOCOLFILTER->ip_p= (val>>8);//get filter ip_p
+    	else val=(val&0x00ff)|((uPROTOCOLFILTER->ip_p)<<8);//set filter ip_p
+    }	
+    if(cmd!=ADM_SW_IOCTL_FILTER_GET) ifx_sw_write(((uPROTOCOLFILTER->protocol_filter_num/2)+0x68), val);//write rx68~rx6b,protocol filter0~7	
+            		
+    	ifx_sw_read(0x95, &val);	//protocol filter action
+    if(cmd==ADM_SW_IOCTL_FILTER_GET) {
+       	uPROTOCOLFILTER->action= ((val>>(uPROTOCOLFILTER->protocol_filter_num*2))&0x3);//get filter action
+    }
+    else {
+    	val=(val&(~(0x03<<(uPROTOCOLFILTER->protocol_filter_num*2))))|(((uPROTOCOLFILTER->action)&0x03)<<(uPROTOCOLFILTER->protocol_filter_num*2));
+        ifx_sw_write(0x95, val);	//write protocol filter action		
+    }
+            	
+	return 0;
+}
+
+
+/* Santosh: function for MAC ENTRY ADD/DEL/GET */
+
+int adm_process_mac_table_request (unsigned int cmd, PMACENTRY mMACENTRY)
+{
+    unsigned int val;		//6996i
+    unsigned int control[6] ;	//6996i
+    unsigned int status[6] ;	//6996i
+
+	// printk ("adm_process_mac_table_request: enter\n");	
+
+    control[0]=(mMACENTRY->mac_addr[1]<<8)+mMACENTRY->mac_addr[0]     ; 
+    control[1]=(mMACENTRY->mac_addr[3]<<8)+mMACENTRY->mac_addr[2]      ;         
+    control[2]=(mMACENTRY->mac_addr[5]<<8)+mMACENTRY->mac_addr[4]     ;
+    control[3]=(mMACENTRY->fid&0xf)+((mMACENTRY->portmap&0x3f)<<4);
+
+    if (((mMACENTRY->info_type)&0x01)) control[4]=(mMACENTRY->ctrl.info_ctrl)+0x1000; //static ,info control
+   		else	control[4]=((mMACENTRY->ctrl.age_timer)&0xff);//not static ,agetimer
+        	if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT) { 	
+	          //initial  the pointer to the first address	
+	           val=0x8000;//busy ,status5[15]
+	           while(val&0x8000){		//check busy ?
+	           ifx_sw_read(0x125, &val);
+	       	}    
+	        control[5]=0x030;//initial the first address	
+	        ifx_sw_write(0x11f,control[5]);
+			        	       	
+			           	
+			           val=0x8000;//busy ,status5[15]
+			           while(val&0x8000){		//check busy ?
+			 	          ifx_sw_read(0x125, &val);
+			        	}           	
+	           	
+	           }	//if (cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)								
+           if (cmd==ADM_SW_IOCTL_MACENTRY_ADD) control[5]=0x07;//create a new address
+           	else if (cmd==ADM_SW_IOCTL_MACENTRY_DEL) control[5]=0x01f;//erased an existed address
+           	else if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) 
+           		control[5]=0x02c;//search by the mac address field
+           
+           val=0x8000;//busy ,status5[15]
+           while(val&0x8000){		//check busy ?
+ 	          ifx_sw_read(0x125, &val);
+        	}
+        	ifx_sw_write(0x11a,control[0]);	
+        	ifx_sw_write(0x11b,control[1]);	
+        	ifx_sw_write(0x11c,control[2]);	
+        	ifx_sw_write(0x11d,control[3]);	
+        	ifx_sw_write(0x11e,control[4]);	
+        	ifx_sw_write(0x11f,control[5]);	
+           val=0x8000;//busy ,status5[15]
+           while(val&0x8000){		//check busy ?
+ 	          ifx_sw_read(0x125, &val);
+        	}	
+           val=((val&0x7000)>>12);//result ,status5[14:12]
+           mMACENTRY->result=val;
+   
+           if (!val) {
+        		printk(" Command OK!! \n");
+        		if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) {
+			           	ifx_sw_read(0x120,&(status[0]));	
+			        	ifx_sw_read(0x121,&(status[1]));	
+			        	ifx_sw_read(0x122,&(status[2]));	
+			        	ifx_sw_read(0x123,&(status[3]));	
+			        	ifx_sw_read(0x124,&(status[4]));	
+			        	ifx_sw_read(0x125,&(status[5]));	
+		
+		           		
+		        		mMACENTRY->mac_addr[0]=(status[0]&0x00ff)	;
+		        		mMACENTRY->mac_addr[1]=(status[0]&0xff00)>>8    ;
+		        		mMACENTRY->mac_addr[2]=(status[1]&0x00ff)    ;
+		        		mMACENTRY->mac_addr[3]=(status[1]&0xff00)>>8 ;
+		        		mMACENTRY->mac_addr[4]=(status[2]&0x00ff)    ;
+		        		mMACENTRY->mac_addr[5]=(status[2]&0xff00)>>8 ;
+		        		mMACENTRY->fid=(status[3]&0xf);
+		        		mMACENTRY->portmap=((status[3]>>4)&0x3f);
+		        		if (status[5]&0x2) {//static info_ctrl //status5[1]????
+		        			mMACENTRY->ctrl.info_ctrl=(status[4]&0x00ff);
+		  				mMACENTRY->info_type=1;
+		        				}
+		        		else {//not static age_timer
+		        			mMACENTRY->ctrl.age_timer=(status[4]&0x00ff);
+		  				mMACENTRY->info_type=0;
+		        				}
+//status5[13]????					mMACENTRY->occupy=(status[5]&0x02)>>1;//status5[1]
+					mMACENTRY->occupy=(status[5]&0x02000)>>13;//status5[13] ???
+					mMACENTRY->bad=(status[5]&0x04)>>2;//status5[2]
+				}//if ((cmd==ADM_SW_IOCTL_MACENTRY_GET_INIT)||(cmd==ADM_SW_IOCTL_MACENTRY_GET_MORE)) 
+			
+        	}
+           else if (val==0x001)  
+                printk(" All Entry Used!! \n");
+            else if (val==0x002) 
+                printk("  Entry Not Found!! \n");
+            else if (val==0x003) 
+                printk(" Try Next Entry!! \n");
+            else if (val==0x005)  
+                printk(" Command Error!! \n");   
+            else   
+                printk(" UnKnown Error!! \n");
+
+	// printk ("adm_process_mac_table_request: Exit\n");	
+	return 0;
+}
+
+/* Santosh: End of function for MAC ENTRY ADD/DEL*/
+struct file_operations adm_ops =
+{
+    read: adm_read,
+    write: adm_write,
+    open: adm_open,
+    release: adm_release,
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,36))
+    unlocked_ioctl: adm_ioctl
+#else
+    ioctl: adm_ioctl
+#endif
+};
+
+int adm_proc(char *buf, char **start, off_t offset, int count, int *eof, void *data)
+{
+    int len = 0;
+
+    len += sprintf(buf+len, " ************ Registers ************ \n");
+    *eof = 1;
+    return len;
+}
+
+int __init init_adm6996_module(void)
+{
+    unsigned int val = 000;
+    unsigned int val1 = 000;
+
+    printk("Loading ADM6996 driver... \n");
+
+    /* if running on adm5120 */
+    /* set GPIO 0~2 as adm6996 control pins */
+    //outl(0x003f3f00, 0x12000028);
+    /* enable switch port 5 (MII) as RMII mode (5120MAC <-> 6996MAC) */
+    //outl(0x18a, 0x12000030);
+    /* group adm5120 port 1 ~ 5 as VLAN0, port 5 & 6(CPU) as VLAN1 */
+    //outl(0x417e, 0x12000040);
+    /* end adm5120 fixup */
+#ifdef ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin
+    register_chrdev(69, "adm6996", &adm_ops);
+    AMAZON_SW_REG(AMAZON_SW_MDIO_CFG) = 0x27be;
+    AMAZON_SW_REG(AMAZON_SW_EPHY) = 0xfc;
+    adm6996_mode=adm6996i;
+    ifx_sw_read(0xa0, &val);
+    ifx_sw_read(0xa1, &val1);
+    val=((val1&0x0f)<<16)|val;
+    printk ("\nADM6996 SMI Mode-");
+    printk ("Chip ID:%5x \n ", val);
+#else    //000001.joelin
+ 
+    AMAZON_SW_REG(AMAZON_SW_MDIO_CFG) = 0x2c50;
+    AMAZON_SW_REG(AMAZON_SW_EPHY) = 0xff;
+
+    AMAZON_SW_REG(AMAZON_GPIO_P1_ALTSEL0) &= ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC);
+    AMAZON_SW_REG(AMAZON_GPIO_P1_ALTSEL1) &= ~(GPIO_MDIO|GPIO_MDCS|GPIO_MDC);
+    AMAZON_SW_REG(AMAZON_GPIO_P1_OD) |= (GPIO_MDIO|GPIO_MDCS|GPIO_MDC);
+  
+    ifx_gpio_init();
+    register_chrdev(69, "adm6996", &adm_ops);
+    mdelay(100);
+
+    /* create proc entries */
+    //  create_proc_read_entry("admide", 0, NULL, admide_proc, NULL);
+
+//joelin adm6996i support start
+    adm6996_mode=adm6996i;
+    ifx_sw_read(0xa0, &val);
+    adm6996_mode=adm6996l;
+    ifx_sw_read(0x200, &val1);
+//  printk ("\n %0x \n",val1);
+    if ((val&0xfff0)==0x1020) {
+        printk ("\n ADM6996I .. \n");
+        adm6996_mode=adm6996i;	
+    }
+    else if ((val1&0xffffff00)==0x71000) {//71010 or 71020
+        printk ("\n ADM6996LC .. \n");
+        adm6996_mode=adm6996lc;	
+    }
+    else  {
+        printk ("\n ADM6996L .. \n");
+        adm6996_mode=adm6996l;	
+    }
+#endif //ADM6996_MDC_MDIO_MODE //smi mode //000001.joelin	
+
+    if ((adm6996_mode==adm6996lc)||(adm6996_mode==adm6996i)){
+#if 0	/* removed by MarsLin */
+        ifx_sw_write(0x29,0xc000);
+        ifx_sw_write(0x30,0x0985);
+#else
+        ifx_sw_read(0xa0, &val);
+        if (val == 0x1021) // for both 6996LC and 6996I, only AB version need the patch
+            ifx_sw_write(0x29, 0x9000);
+        ifx_sw_write(0x30,0x0985);
+#endif
+    }
+//joelin adm6996i support end
+    return 0;
+}
+
+void __exit cleanup_adm6996_module(void)
+{
+    printk("Free ADM device driver... \n");
+
+    unregister_chrdev(69, "adm6996");
+
+    /* remove proc entries */
+    //  remove_proc_entry("admide", NULL);
+}
+
+/* MarsLin, add start */
+#if defined(CONFIG_IFX_NFEXT_AMAZON_SWITCH_PHYPORT) || defined(CONFIG_IFX_NFEXT_AMAZON_SWITCH_PHYPORT_MODULE)
+    #define SET_BIT(reg, mask)		reg |= (mask)
+    #define CLEAR_BIT(reg, mask)	reg &= (~mask)
+    static int ifx_hw_reset(void)
+    {
+        CLEAR_BIT((*AMAZON_GPIO_P0_ALTSEL0),0x2000);
+        CLEAR_BIT((*AMAZON_GPIO_P0_ALTSEL1),0x2000);
+        SET_BIT((*AMAZON_GPIO_P0_OD),0x2000);
+        SET_BIT((*AMAZON_GPIO_P0_DIR), 0x2000);
+	CLEAR_BIT((*AMAZON_GPIO_P0_OUT), 0x2000);
+	mdelay(500);
+	SET_BIT((*AMAZON_GPIO_P0_OUT), 0x2000);
+        cleanup_adm6996_module();
+        return init_adm6996_module();
+    }
+    int (*adm6996_hw_reset)(void) = ifx_hw_reset;
+    EXPORT_SYMBOL(adm6996_hw_reset);
+    EXPORT_SYMBOL(adm6996_mode);
+    int (*adm6996_sw_read)(unsigned int addr, unsigned int *data) = ifx_sw_read;
+    EXPORT_SYMBOL(adm6996_sw_read);
+    int (*adm6996_sw_write)(unsigned int addr, unsigned int data) = ifx_sw_write;
+    EXPORT_SYMBOL(adm6996_sw_write);
+#endif
+/* MarsLin, add end */
+
+/* Santosh: for IGMP proxy/snooping, Begin */
+EXPORT_SYMBOL (adm_process_mac_table_request);
+EXPORT_SYMBOL (adm_process_protocol_filter_request);
+/* Santosh: for IGMP proxy/snooping, End */
+	
+MODULE_DESCRIPTION("ADMtek 6996 Driver");
+MODULE_AUTHOR("Joe Lin <joe.lin@infineon.com>");
+MODULE_LICENSE("GPL");
+
+module_init(init_adm6996_module);
+module_exit(cleanup_adm6996_module);
+