strip the kernel version suffix from target directories, except for brcm-2.4 (the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@8653 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 191 insertions, 0 deletions

diff --git a/target/linux/adm5120/files/include/asm-mips/mach-adm5120/prom/myloader.h b/target/linux/adm5120/files/include/asm-mips/mach-adm5120/prom/myloader.h
new file mode 100644
index 0000000000..526de865c9
--- /dev/null
+++ b/target/linux/adm5120/files/include/asm-mips/mach-adm5120/prom/myloader.h
@@ -0,0 +1,191 @@
+/*
+ *  $Id$
+ *
+ *  Compex's MyLoader specific definitions
+ *
+ *  Copyright (C) 2006,2007 Gabor Juhos <juhosg at openwrt.org>
+ *  Copyright (C) 2007 OpenWrt.org
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  as published by the Free Software Foundation; either version 2
+ *  of the License, or (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the
+ *  Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor,
+ *  Boston, MA  02110-1301, USA.
+ */
+
+#ifndef _MYLOADER_H_
+#define _MYLOADER_H_
+
+/*
+ * Firmware file format:
+ *
+ *	<header>
+ *	[<block descriptor 0>]
+ *	...
+ *	[<block descriptor n>]
+ *	<null block descriptor>
+ *	[<block data 0>]
+ *	...
+ *	[<block data n>]
+ *
+ *
+ */
+
+/* Myloader specific magic numbers */
+#define MYLO_MAGIC_FIRMWARE	0x4C594D00
+#define MYLO_MAGIC_20021103	0x20021103
+#define MYLO_MAGIC_20021107	0x20021107
+
+#define MYLO_MAGIC_SYS_PARAMS	MYLO_MAGIC_20021107
+#define MYLO_MAGIC_PARTITIONS	MYLO_MAGIC_20021103
+#define MYLO_MAGIC_BOARD_PARAMS	MYLO_MAGIC_20021103
+
+/*
+ * Addresses of the data structures provided by MyLoader
+ */
+#define MYLO_MIPS_SYS_PARAMS	0x80000800	/* System Parameters */
+#define MYLO_MIPS_BOARD_PARAMS	0x80000A00	/* Board Parameters */
+#define MYLO_MIPS_PARTITIONS	0x80000C00	/* Partition Table */
+#define MYLO_MIPS_BOOT_PARAMS	0x80000E00	/* Boot Parameters */
+
+/* Vendor ID's (seems to be same as the PCI vendor ID's) */
+#define VENID_COMPEX		0x11F6
+
+/* Devices based on the ADM5120 */
+#define DEVID_COMPEX_NP27G	0x0078
+#define DEVID_COMPEX_NP28G	0x044C
+#define DEVID_COMPEX_NP28GHS	0x044E
+#define DEVID_COMPEX_WP54Gv1C	0x0514
+#define DEVID_COMPEX_WP54G	0x0515
+#define DEVID_COMPEX_WP54AG	0x0546
+#define DEVID_COMPEX_WPP54AG	0x0550
+#define DEVID_COMPEX_WPP54G	0x0555
+
+/* Devices based on the IXP422 */
+#define DEVID_COMPEX_WP18	0x047E
+#define DEVID_COMPEX_NP18A	0x0489
+
+/* Other devices */
+#define DEVID_COMPEX_NP26G8M	0x03E8
+#define DEVID_COMPEX_NP26G16M	0x03E9
+
+struct mylo_fw_header {
+	uint32_t	magic;	/* must be MYLO_MAGIC_FIRMWARE */
+	uint32_t	crc;	/* CRC of the whole firmware */
+	uint32_t	res0;	/* unknown/unused */
+	uint32_t	res1;	/* unknown/unused */
+	uint16_t	vid;	/* vendor ID */
+	uint16_t	did;	/* device ID */
+	uint16_t	svid;	/* sub vendor ID */
+	uint16_t	sdid;	/* sub device ID */
+	uint32_t	rev;	/* device revision */
+	uint32_t	fwhi;	/* FIXME: firmware version high? */
+	uint32_t	fwlo;	/* FIXME: firmware version low? */
+	uint32_t	flags;	/* firmware flags */
+};
+
+#define FW_FLAG_BOARD_PARAMS_WP	0x01 /* board parameters are write protected */
+#define FW_FLAG_BOOT_SECTOR_WE	0x02 /* enable of write boot sectors (below 64K) */
+
+struct mylo_fw_blockdesc {
+	uint32_t	type;	/* block type */
+	uint32_t	addr;	/* relative address to flash start */
+	uint32_t	dlen;	/* size of block data in bytes */
+	uint32_t	blen;	/* total size of block in bytes */
+};
+
+#define FW_DESC_TYPE_UNUSED	0
+#define FW_DESC_TYPE_USED	1
+
+struct mylo_partition {
+	uint16_t	flags;	/* partition flags */
+	uint16_t	type;	/* type of the partition */
+	uint32_t	addr;	/* relative address of the partition from the
+				   flash start */
+	uint32_t	size;	/* size of the partition in bytes */
+	uint32_t	param;	/* if this is the active partition, the
+				   MyLoader load code to this address */
+};
+
+#define PARTITION_FLAG_ACTIVE	0x8000 /* this is the active partition,
+					* MyLoader loads firmware from here */
+#define PARTITION_FLAG_ISRAM	0x2000 /* FIXME: this is a RAM partition? */
+#define PARTIIION_FLAG_RAMLOAD	0x1000 /* FIXME: load this partition into the RAM? */
+#define PARTITION_FLAG_PRELOAD	0x0800 /* the partition data preloaded to RAM
+					* before decompression */
+#define PARTITION_FLAG_HAVEHDR  0x0002 /* the partition data have a header */
+
+#define PARTITION_TYPE_FREE	0
+#define PARTITION_TYPE_USED	1
+
+#define MYLO_MAX_PARTITIONS	8	/* maximum number of partitions in the
+					   partition table */
+
+struct mylo_partition_table {
+	uint32_t	magic;	/* must be MYLO_MAGIC_PARTITIONS */
+	uint32_t	res0;	/* unknown/unused */
+	uint32_t	res1;	/* unknown/unused */
+	uint32_t 	res2;	/* unknown/unused */
+	struct mylo_partition partitions[MYLO_MAX_PARTITIONS];
+};
+
+struct mylo_partition_header {
+	uint32_t	len;	/* length of the partition data */
+	uint32_t	crc;	/* CRC value of the partition data */
+};
+
+struct mylo_system_params {
+	uint32_t	magic;	/* must be MYLO_MAGIC_SYS_PARAMS */
+	uint32_t	res0;
+	uint32_t	res1;
+	uint32_t	mylo_ver;
+	uint16_t	vid;	/* Vendor ID */
+	uint16_t	did;	/* Device ID */
+	uint16_t	svid;	/* Sub Vendor ID */
+	uint16_t	sdid;	/* Sub Device ID */
+	uint32_t	rev;	/* device revision */
+	uint32_t	fwhi;
+	uint32_t	fwlo;
+	uint32_t	tftp_addr;
+	uint32_t	prog_start;
+	uint32_t	flash_size;	/* Size of boot FLASH in bytes */
+	uint32_t	dram_size;	/* Size of onboard RAM in bytes */
+};
+
+
+struct mylo_eth_addr {
+	uint8_t	mac[6];
+	uint8_t	csum[2];
+};
+
+#define MYLO_ETHADDR_COUNT	8	/* maximum number of ethernet address
+					   in the board parameters */
+
+struct mylo_board_params {
+	uint32_t	magic;	/* must be MYLO_MAGIC_BOARD_PARAMS */
+	uint32_t	res0;
+	uint32_t	res1;
+	uint32_t	res2;
+	struct mylo_eth_addr addr[MYLO_ETHADDR_COUNT];
+};
+
+struct myloader_info {
+	u32	vid;
+	u32	did;
+	u32	svid;
+	u32	sdid;
+};
+
+extern struct myloader_info myloader_info;
+extern int myloader_present(void) __init;
+
+#endif /* _MYLOADER_H_*/