add default configs for kismet

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@723 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 120 insertions, 0 deletions

diff --git a/openwrt/package/kismet/files/kismet_drone.conf b/openwrt/package/kismet/files/kismet_drone.conf
new file mode 100644
index 0000000000..865278ab7a
--- /dev/null
+++ b/openwrt/package/kismet/files/kismet_drone.conf
@@ -0,0 +1,120 @@
+# Kismet drone config file
+
+version=Feb.04.01a
+
+# Name of server (Purely for organiational purposes)
+servername=Kismet
+
+# User to setid to (should be your normal user)
+suiduser=your_user_here
+
+# Port to serve packet data... This probably shouldn't be the same as the port
+# you configured kismet_server for, or else you'll have problems running them 
+# on the same system.
+tcpport=3501
+# People allowed to connect, comma seperated IP addresses or network/mask
+# blocks.  Netmasks can be expressed as dotted quad (/255.255.255.0) or as
+# numbers (/24)
+allowedhosts=127.0.0.1
+# Maximum number of concurrent stream attachments
+maxclients=5
+
+# Packet sources:
+# source=capture_cardtype,capture_interface,capture_name
+# Card type - Specifies the type of device. It can be one of:
+#     cisco         - Cisco card with Linux Kernel drivers 
+#     cisco_cvs     - Cisco card with CVS Linux drivers
+#     cisco_bsd     - Cisco on *BSD
+#     prism2        - Prism2 using wlan-ng drivers with pcap support (all 
+#                      current versions support pcap)
+#     prism2_hostap - Prism2 using hostap drivers
+#     prism2_legacy - Prism2 using wlan-ng drivers without pcap support (0.1.9)
+#     prism2_bsd    - Prism2 on *BSD
+#     orinoco       - Orinoco cards using Snax's patched driers
+#     generic       - Generic card with no specific support.  You will have 
+#                      to put this into monitor mode yourself!
+#     wsp100        - WSP100 embedded remote sensor.  
+#     wtapfile      - Saved file of packets readable by libwiretap
+#     ar5k          - ar5k 802.11a using the vt_ar5k drivers
+# Capture interface - Specifies the network interface Kismet will watch for
+#  packets to come in on.  Typically "ethX" or "wlanX".  For the WSP100 capture
+#  engine, the WSP100 device sends packets via a UDP stream, so the capture
+#  interface should be in the form of host:port where 'host' is the WSP100 and 
+#  'port' is the local UDP port that it will send data to.
+# Capture Name      - The name Kismet uses for this capture source.  This is the 
+#   name used to specify what sources to enable.
+# 
+# To enable multiple sources, specify a source line for each and then use the
+# enablesources line to enable them.  For example:
+# source=prism2,wlan0,prism
+# source=cisco,eth0,cisco
+
+source=generic,prism0,Kismet-Drone
+
+# Comma-separated list of sources to enable.  This is only needed if you wish 
+# to selectively enable multiple sources.
+# enablesources=prism,cisco
+
+# Do we channelhop?
+channelhop=true
+
+# How many channels per second do we hop?  (1-10)
+channelvelocity=5
+
+# By setting the dwell time for channel hopping we override the channelvelocity
+# setting above and dwell on each channel for the given number of seconds.
+#channeldwell=10
+
+# Do we split channels between cards on the same spectrum?  This means if 
+# multiple 802.11b capture sources are defined, they will be offset to cover
+# the most possible spectrum at a given time.  This also controls splitting
+# fine-tuned sourcechannels lines which cover multiple interfaces (see below)
+splitchannels=true
+
+# Basic channel hopping control:
+# These define the channels the cards hop through for various frequency ranges
+# supported by Kismet.   More finegrain control is available via the 
+# "sourcechannels" configuration option.
+# 
+# Don't change the IEEE80211<x> identifiers or channel hopping won't work.
+
+# Users outside the US might want to use this list:
+# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12
+defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10
+
+# 802.11g uses the same channels as 802.11b...
+defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10
+
+# 802.11a channels are non-overlapping so sequential is fine.  You may want to
+# adjust the list depending on the channels your card actually supports.
+# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216 
+defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64
+
+# Combo cards like Atheros use both 'a' and 'b/g' channels.  Of course, you
+# can also explicitly override a given source.  You can use the script 
+# extras/listchan.pl to extract all the channels your card supports.
+defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64
+
+# Fine-tuning channel hopping control:
+# The sourcechannels option can be used to set the channel hopping for 
+# specific interfaces, and to control what interfaces share a list of 
+# channels for split hopping.  This can also be used to easily lock
+# one card on a single channel while hopping with other cards.
+# Any card without a sourcechannel definition will use the standard hopping
+# list.
+# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN
+
+# ie, for us channels on the source 'prism2source' (same as normal channel
+# hopping behavior):
+# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10
+
+# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay
+# on channel 6 and prism2b to hop normally.  By not setting a sourcechannels 
+# line for prism2b, it will use the standard hopping.
+# sourcechannels=prism2a:6
+
+# To assign the same custom hop channel to multiple sources, or to split the 
+# same custom hop channel over two sources (if splitchannels is true), list
+# them all on the same sourcechannels line:
+# sourcechannels=prism2a,prism2b,prism2c:1,6,11
+