1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
|
#ifndef __NET_WIRELESS_H
#define __NET_WIRELESS_H
/*
* 802.11 device management
*
* Copyright 2007 Johannes Berg <johannes@sipsolutions.net>
*/
#include <linux/netdevice.h>
#include <linux/debugfs.h>
#include <linux/list.h>
#include <net/cfg80211.h>
/**
* enum ieee80211_band - supported frequency bands
*
* The bands are assigned this way because the supported
* bitrates differ in these bands.
*
* @IEEE80211_BAND_2GHZ: 2.4GHz ISM band
* @IEEE80211_BAND_5GHZ: around 5GHz band (4.9-5.7)
*/
enum ieee80211_band {
IEEE80211_BAND_2GHZ,
IEEE80211_BAND_5GHZ,
/* keep last */
IEEE80211_NUM_BANDS
};
/**
* enum ieee80211_channel_flags - channel flags
*
* Channel flags set by the regulatory control code.
*
* @IEEE80211_CHAN_DISABLED: This channel is disabled.
* @IEEE80211_CHAN_PASSIVE_SCAN: Only passive scanning is permitted
* on this channel.
* @IEEE80211_CHAN_NO_IBSS: IBSS is not allowed on this channel.
* @IEEE80211_CHAN_RADAR: Radar detection is required on this channel.
*/
enum ieee80211_channel_flags {
IEEE80211_CHAN_DISABLED = 1<<0,
IEEE80211_CHAN_PASSIVE_SCAN = 1<<1,
IEEE80211_CHAN_NO_IBSS = 1<<2,
IEEE80211_CHAN_RADAR = 1<<3,
};
/**
* struct ieee80211_channel - channel definition
*
* This structure describes a single channel for use
* with cfg80211.
*
* @center_freq: center frequency in MHz
* @hw_value: hardware-specific value for the channel
* @flags: channel flags from &enum ieee80211_channel_flags.
* @orig_flags: channel flags at registration time, used by regulatory
* code to support devices with additional restrictions
* @band: band this channel belongs to.
* @max_antenna_gain: maximum antenna gain in dBi
* @max_power: maximum transmission power (in dBm)
* @orig_mag: internal use
* @orig_mpwr: internal use
*/
struct ieee80211_channel {
enum ieee80211_band band;
u16 center_freq;
u16 hw_value;
u32 flags;
int max_antenna_gain;
int max_power;
u32 orig_flags;
int orig_mag, orig_mpwr;
};
/**
* enum ieee80211_rate_flags - rate flags
*
* Hardware/specification flags for rates. These are structured
* in a way that allows using the same bitrate structure for
* different bands/PHY modes.
*
* @IEEE80211_RATE_SHORT_PREAMBLE: Hardware can send with short
* preamble on this bitrate; only relevant in 2.4GHz band and
* with CCK rates.
* @IEEE80211_RATE_MANDATORY_A: This bitrate is a mandatory rate
* when used with 802.11a (on the 5 GHz band); filled by the
* core code when registering the wiphy.
* @IEEE80211_RATE_MANDATORY_B: This bitrate is a mandatory rate
* when used with 802.11b (on the 2.4 GHz band); filled by the
* core code when registering the wiphy.
* @IEEE80211_RATE_MANDATORY_G: This bitrate is a mandatory rate
* when used with 802.11g (on the 2.4 GHz band); filled by the
* core code when registering the wiphy.
* @IEEE80211_RATE_ERP_G: This is an ERP rate in 802.11g mode.
*/
enum ieee80211_rate_flags {
IEEE80211_RATE_SHORT_PREAMBLE = 1<<0,
IEEE80211_RATE_MANDATORY_A = 1<<1,
IEEE80211_RATE_MANDATORY_B = 1<<2,
IEEE80211_RATE_MANDATORY_G = 1<<3,
IEEE80211_RATE_ERP_G = 1<<4,
};
/**
* struct ieee80211_rate - bitrate definition
*
* This structure describes a bitrate that an 802.11 PHY can
* operate with. The two values @hw_value and @hw_value_short
* are only for driver use when pointers to this structure are
* passed around.
*
* @flags: rate-specific flags
* @bitrate: bitrate in units of 100 Kbps
* @hw_value: driver/hardware value for this rate
* @hw_value_short: driver/hardware value for this rate when
* short preamble is used
*/
struct ieee80211_rate {
u32 flags;
u16 bitrate;
u16 hw_value, hw_value_short;
};
/**
* struct ieee80211_ht_info - describing STA's HT capabilities
*
* This structure describes most essential parameters needed
* to describe 802.11n HT capabilities for an STA.
*
* @ht_supported: is HT supported by STA, 0: no, 1: yes
* @cap: HT capabilities map as described in 802.11n spec
* @ampdu_factor: Maximum A-MPDU length factor
* @ampdu_density: Minimum A-MPDU spacing
* @supp_mcs_set: Supported MCS set as described in 802.11n spec
*/
struct ieee80211_ht_info {
u16 cap; /* use IEEE80211_HT_CAP_ */
u8 ht_supported;
u8 ampdu_factor;
u8 ampdu_density;
u8 supp_mcs_set[16];
};
/**
* struct ieee80211_supported_band - frequency band definition
*
* This structure describes a frequency band a wiphy
* is able to operate in.
*
* @channels: Array of channels the hardware can operate in
* in this band.
* @band: the band this structure represents
* @n_channels: Number of channels in @channels
* @bitrates: Array of bitrates the hardware can operate with
* in this band. Must be sorted to give a valid "supported
* rates" IE, i.e. CCK rates first, then OFDM.
* @n_bitrates: Number of bitrates in @bitrates
*/
struct ieee80211_supported_band {
struct ieee80211_channel *channels;
struct ieee80211_rate *bitrates;
enum ieee80211_band band;
int n_channels;
int n_bitrates;
struct ieee80211_ht_info ht_info;
};
/**
* struct wiphy - wireless hardware description
* @idx: the wiphy index assigned to this item
* @class_dev: the class device representing /sys/class/ieee80211/<wiphy-name>
*/
struct wiphy {
/* assign these fields before you register the wiphy */
/* permanent MAC address */
u8 perm_addr[ETH_ALEN];
/* If multiple wiphys are registered and you're handed e.g.
* a regular netdev with assigned ieee80211_ptr, you won't
* know whether it points to a wiphy your driver has registered
* or not. Assign this to something global to your driver to
* help determine whether you own this wiphy or not. */
void *privid;
struct ieee80211_supported_band *bands[IEEE80211_NUM_BANDS];
/* fields below are read-only, assigned by cfg80211 */
/* the item in /sys/class/ieee80211/ points to this,
* you need use set_wiphy_dev() (see below) */
struct device dev;
/* dir in debugfs: ieee80211/<wiphyname> */
struct dentry *debugfsdir;
char priv[0] __attribute__((__aligned__(NETDEV_ALIGN)));
};
/** struct wireless_dev - wireless per-netdev state
*
* This structure must be allocated by the driver/stack
* that uses the ieee80211_ptr field in struct net_device
* (this is intentional so it can be allocated along with
* the netdev.)
*
* @wiphy: pointer to hardware description
*/
struct wireless_dev {
struct wiphy *wiphy;
/* private to the generic wireless code */
struct list_head list;
struct net_device *netdev;
};
/**
* wiphy_priv - return priv from wiphy
*/
static inline void *wiphy_priv(struct wiphy *wiphy)
{
BUG_ON(!wiphy);
return &wiphy->priv;
}
/**
* set_wiphy_dev - set device pointer for wiphy
*/
static inline void set_wiphy_dev(struct wiphy *wiphy, struct device *dev)
{
wiphy->dev.parent = dev;
}
/**
* wiphy_dev - get wiphy dev pointer
*/
static inline struct device *wiphy_dev(struct wiphy *wiphy)
{
return wiphy->dev.parent;
}
/**
* wiphy_name - get wiphy name
*/
static inline char *wiphy_name(struct wiphy *wiphy)
{
return wiphy->dev.bus_id;
}
/**
* wdev_priv - return wiphy priv from wireless_dev
*/
static inline void *wdev_priv(struct wireless_dev *wdev)
{
BUG_ON(!wdev);
return wiphy_priv(wdev->wiphy);
}
/**
* wiphy_new - create a new wiphy for use with cfg80211
*
* create a new wiphy and associate the given operations with it.
* @sizeof_priv bytes are allocated for private use.
*
* the returned pointer must be assigned to each netdev's
* ieee80211_ptr for proper operation.
*/
struct wiphy *wiphy_new(struct cfg80211_ops *ops, int sizeof_priv);
/**
* wiphy_register - register a wiphy with cfg80211
*
* register the given wiphy
*
* Returns a non-negative wiphy index or a negative error code.
*/
extern int wiphy_register(struct wiphy *wiphy);
/**
* wiphy_unregister - deregister a wiphy from cfg80211
*
* unregister a device with the given priv pointer.
* After this call, no more requests can be made with this priv
* pointer, but the call may sleep to wait for an outstanding
* request that is being handled.
*/
extern void wiphy_unregister(struct wiphy *wiphy);
/**
* wiphy_free - free wiphy
*/
extern void wiphy_free(struct wiphy *wiphy);
/**
* ieee80211_channel_to_frequency - convert channel number to frequency
*/
extern int ieee80211_channel_to_frequency(int chan);
/**
* ieee80211_frequency_to_channel - convert frequency to channel number
*/
extern int ieee80211_frequency_to_channel(int freq);
#endif /* __NET_WIRELESS_H */
|
