summaryrefslogtreecommitdiff
path: root/target
AgeCommit message (Collapse)Author
2013-02-15bcm63xx: make nvram checksum failures non fataljogo
fixes #12982. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35605 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-15kernel: update linux 3.7 to 3.7.8juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35604 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-14generic: ar8216: move PHY4 RGMII workaround code out of the loopjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35603 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-14generic: ar8216: register the switch from the probe routinejuhosg
Currently the switch gets registered when an ethernet driver connects to a PHY of the switch. This method does not work with the ethernet drivers which are connecting to the PHY from their ndo_open callback. With those ethernet drivers, the driver tries to register the switch each time when the etherned device is opened and this causes a deadlock. Move the switch registration into the probe routine to fix this problem. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35602 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-14x86: update config-3.7 for x86 (turn off CONFIG_GPIO_ICH)florian
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Florian Fainelli <florian@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35601 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-14brcm47xx: if the cpuport of the switch is port 8 assume vlan0ports: "1 2 3 4 ↵hauke
8" and vlan0ports: "0 8" git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35597 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-13mpc85xx: enable swconfig and the ar8216 driverjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35592 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-13mpc85xx: enable the squashfs driverjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35591 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-13mpc85xx: enable XZ_DEC_BCJ and XZ_DEC_POWERPC supportjuhosg
Squashfs is unable to decompress some blocks without that: [ 199.494500] SQUASHFS error: xz_dec_run error, data probably corrupt [ 199.500910] SQUASHFS error: squashfs_read_data failed to read block 0xbff26 [ 199.508016] SQUASHFS error: Unable to read data cache entry [bff26] [ 199.514440] SQUASHFS error: Unable to read page, block bff26, size 153f8 [ 199.521311] SQUASHFS error: Unable to read data cache entry [bff26] [ 199.527724] SQUASHFS error: Unable to read page, block bff26, size 153f8 [ 199.534594] SQUASHFS error: Unable to read data cache entry [bff26] [ 199.541009] SQUASHFS error: Unable to read page, block bff26, size 153f8 Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35590 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-13ar71xx: fix factory image creation for dir-825-c1juhosg
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35589 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-13ar71xx: fix switch-config for dir-825-c1juhosg
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35588 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-13brcm47xx: configure vlan correctly on some recent devices.hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35587 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-12brcm47xx: add some more fixes to bgmachauke
Thank you Rafał Miłecki and Nathan Hintz git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35574 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-12brcm47xx: update tg3 to the version send upstreamhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35573 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-12mvebu: remove boards suffixluka
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35572 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-12kernel: update linux 3.7 to 3.7.7juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35571 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11ar71xx: add script for automatic switch name migrationjuhosg
Thanks to Jonas Gorski for the help. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35567 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11ar71xx: allow unknown multicast frames to pass to the CPU on AR934xnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35564 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11ar8216: remove superfluous code from ar8216_config_initjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35562 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11ar71xx: use switchX names in network configurationjuhosg
Accessing the AR8xxx switches via the name of the attached ethernet device is not possible since r35560. Change the uci-defaults script to use switchX names in switch configurations. Reported-by: Jonas Gorski <jogo@openwrt.org> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35561 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11generic: ar8216: don't use ethernet device name in register_switchjuhosg
The switches are accessed via an MDIO bus. Set the alias to the name of the MDIO bus, and show that in the message along with the name of the switch switch device. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35560 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11generic: ar8216: reuse the private data from ar8216_probejuhosg
The private data of the switch is already allocated in ar8216_priv, assign that to each PHY on the same MDIO bus. Also remove the redundant code from ar8216_config_init. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35559 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11generic: ar8216: use phydev instead of pdev everywherejuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35555 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11generic: ar8216: use pr_* macros for kernel messagesjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35554 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11generic: ar8216: fix PHY features setupjuhosg
Sujith says: This commit breaks the WAN port on my AP96 - DHCP fails. Reverting it fixes the issue. commit b67cc3a0cdd02973610d4d5a63226d1c44841e94 Author: juhosg <juhosg@3c298f89-4303-0410-b956-a3cf2f4a3e73> Date: Fri Feb 8 09:13:18 2013 +0000 generic: ar8216: simplify phy features setup Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@355183c298f89-4303-0410-b956-a3cf2f4a3e73 This change restores the previous behaviour and moves the code into the ar8216_probe function. Reported-by: Sujith Manoharan <sujith@msujith.org> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Tested-by: Sujith Manoharan <sujith@msujith.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35549 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: add ar8xxx_probe_switch helperjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35547 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: rename ar8xxx_mib_cleanup to ar8xxx_mib_stopjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35546 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: free mib counters from ar8xxx_freejuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35545 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: add ar8xxx_free helperjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35544 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: add ar8xxx_create{,mii} helpersjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35543 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: remove redundant phy address checkjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35542 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: only set phy_ptr if packet mangling is usedjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35541 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: add defines for the AR8316 POSTRIP registerjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35539 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: don't probe the chip multiple timesjuhosg
It is only needed when the private data is allocated. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35538 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: add sanity check to ar8216_probejuhosg
Verify that the mdio bus has PHY devices with a supported PHY ID at address 0-4. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35537 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: ar8216: skip probe on unused PHY addressesjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35536 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10ar71xx: register the micro sd card reader on RB493Gjogo
Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35535 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10generic: b53: fix reverted error check in probejogo
b53_switch_detect returns value returned by b53_read8, which is 0 for success. So fail (and return error) only if b53_switch_detect returned something else than 0. This fixes supported and advertising being zeros for MDIO access. Cc: Jonas Gorski <jogo@openwrt.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35534 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-10bcm63xx: handle huawei nvram layoutjogo
Use a different length for calculating the nvram checksum on hauwei boards. Fixes boot on HW553 and HW556. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35533 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-09generic: ar8216: move sleep out of the loopjuhosg
It is enough to sleep once after ANEG is enabled on all PHYs. This reduces boot time on boards with AR8316 switch. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35532 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-08ar71xx: Routerboard 751 Mac Address Offset Fixjuhosg
We utilize many Routerboard 751's and discovered that our latest batch of RB751's would not initialize the wireless radio. We have determined Mikrotik has changed where the mac address was located inside hardconfig. As such we utilize "routerboot_find_tag" to find the location of the mac address. We should remove "RB751_MAC_ADDRESS_OFFSET" as it is ambiguous by machine manufacturing date. The newer batch of RB751's that we received had a RB751_MAC_ADDRESS_OFFSET 0x10. Signed-off-by: Davey Hutchison <dhutchison@bluemesh.net> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35519 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-08generic: ar8216: simplify phy features setupjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35518 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-08generic: ar8216: don't use mdio bus specific functions in ar8216_id_chipjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35517 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-07generic: ar8216: use inline function to convert swdev to ar8216juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35514 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-07generic: ar8216: add mii_bus field to struct ar8216_privjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35513 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-07generic: mvswitch: add detach callbackjuhosg
Use the detach callback to disable packet mangling to avoid possible NULL pointer dereference. Compile tested only. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35512 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-07generic: ar8216: add detach callbackjuhosg
The current code uses the 'remove' callback to disable packet mangle on the underlying ethernet device. However the attached_dev is always NULL when the 'remove' callback is called by phylib, and this causes NULL pointer dereference, like this: [ 475.300000] CPU 0 Unable to handle kernel paging request at virtual address 000000f0, epc == 801cdcf0, ra == 801c7eac [ 475.310000] Oops[#1]: [ 475.310000] Cpu 0 [ 475.310000] $ 0 : 00000000 00000000 00000000 00000001 [ 475.310000] $ 4 : 828dde00 00000005 828dde08 ffffffff [ 475.310000] $ 8 : 00380081 00380081 82902a40 00000001 [ 475.310000] $12 : 00000037 00370081 00000001 00000000 [ 475.310000] $16 : 82865000 828dde08 828dde00 00000001 [ 475.310000] $20 : 00000080 00460000 00000002 77151448 [ 475.310000] $24 : 00000000 801abfd4 [ 475.310000] $28 : 82cc2000 82cc3d58 0053c3c4 801c7eac [ 475.310000] Hi : 00000007 [ 475.310000] Lo : 00000004 [ 475.310000] epc : 801cdcf0 ar8216_remove+0x1c/0x94 [ 475.310000] Tainted: G O [ 475.310000] ra : 801c7eac phy_remove+0x4c/0x6c [ 475.310000] Status: 1000cc03 KERNEL EXL IE [ 475.310000] Cause : 00800008 [ 475.310000] BadVA : 000000f0 [ 475.310000] PrId : 00019750 (MIPS 74Kc) [ 475.310000] Modules linked in: ath79_wdt ledtrig_usbdev ledtrig_netdev ag71xx(-) nf_nat_irc nf_nat_ftp nf_conntrack_irc nf_conntrack_ft p ipt_MASQUERADE iptable_nat xt_nat nf_nat_ipv4 nf_nat pppoext_conntrack xt_CT iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_co nntrack ehci_hcd pppox ipt_REJECT xt_TCPMSS xt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpu dp x_tables ppp_async ppp_generic slhc ath9k(O) ath9k_common(O) ath9k_hw(O) ath(O) mac80211(O) usbcore usb_common nls_base crc_ccitt cfg80 211(O) compat(O) arc4 crypto_blkcipher aead ledtrig_timer ledtrig_default_on leds_gpio gpio_button_hotplug(O) [ 475.310000] Process rmmod (pid: 1160, threadinfo=82cc2000, task=83969920, tls=7747c440) [ 475.310000] Stack : 828dde08 802f5004 802f4680 00000001 828ddf70 801c7eac 802f4680 801ad6d8 82902940 00000000 828dde08 802f5004 802f4680 801ad770 00000002 80269d94 00000000 00000001 00000080 828dde08 828dde3c 801ad7fc 82902940 00000000 83859100 00000000 8384dd2c 8384dd2c 828dde08 801ad230 82902800 00000000 00000000 001a0041 828dde08 828dde08 802e80e8 801aac44 00000080 00460000 ... [ 475.310000] Call Trace: [ 475.310000] [<801cdcf0>] ar8216_remove+0x1c/0x94 [ 475.310000] [<801c7eac>] phy_remove+0x4c/0x6c [ 475.310000] [<801ad770>] __device_release_driver+0x6c/0xd0 [ 475.310000] [<801ad7fc>] device_release_driver+0x28/0x40 [ 475.310000] [<801ad230>] bus_remove_device+0xd8/0x10c [ 475.310000] [<801aac44>] device_del+0x110/0x170 [ 475.310000] [<801aacb8>] device_unregister+0x14/0x28 [ 475.310000] [<801c92b0>] mdiobus_unregister+0x4c/0x70 [ 475.310000] [<82913060>] ag71xx_remove_ar8216_header+0xdc/0x5a8 [ag71xx] [ 475.310000] [ 475.310000] Code: 1200001c 8c82017c ac800128 <8c4500f0> 3c03ffdf 3463ffff 00a31824 ac4300f0 ac4000e0 Add a detach callback and disable packet mangling in that to fix the problem. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35511 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-07generic: add detach callback to struct phy_driverjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35510 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-06brcm47xx: fix name of kmod-ocf-ubsec-ssbhauke
This also removes kmod-ocf, because kmod-crypto-ocf is automatically selected by kmod-ocf-ubsec-ssb. Thank you Manuel Munz <freifunk@somakoma.de> for the patch. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35509 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-06brcm47xx: bgmac: make it possible to set the devices into promisc mode when ↵hauke
it is already up This fixes #12927. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35507 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.46.0) at 2024-12-29 03:42:29 +0000