summaryrefslogtreecommitdiff
path: root/target/linux
AgeCommit message (Collapse)Author
2012-05-27[lantiq] dgn3500 support with eeprom loading from sysfsblogic
WIFI eeprom: As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data. SPI flash: It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above. I've kept the original mtd partitioning that Netgear uses. Buttons/LED: Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working. The green wifi led is connected to an unknown atheros gpio. Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31910 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27[lantiq] fixes zyxel p2601hnfxblogic
moves the linux partition, removes the config partition and the buttons settings have small adjustments. Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31909 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27[lantiq] Add basic configuration for new board ZTE H201L. Still missing are ↵blogic
button and led gpio values. Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31908 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27kernel: properly pad the allocated headroom in skb_cow to NET_SKB_PADnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31906 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27linux/3.2: R.I.P.juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31905 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27xburst: remove support for old kernelsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31904 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27xburst: switch to 3.3 and add broken flagjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31903 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27xburst: add support for 3.3juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31902 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27ppc44x: remove 3.2 supportjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31901 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27ppx44x: switch to 3.3 and add broken flagjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31900 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27ppc44x: add support for 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31899 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27cobalt: switch to 3.3 and add broken flagjuhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31898 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27ep93xx: remove 3.2 supportjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31897 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27ep93xx: switch to 3.3 and add broken flagjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31896 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27ep93xx: add support for 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31895 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27au1000: remove 3.2 supportjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31894 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27au1000: switch to 3.3 and add broken flagjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31893 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27au1000: add support for 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31892 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27linux/3.1: R.I.P.juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31891 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27omap24xx: remove 3.1 supportjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31890 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27omap24xx: switch to 3.3 and add broken flagjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31889 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27cns3xxx: remove 3.1 supportjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31888 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27cns3xxx: switch to 3.3 and add broken flagjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31887 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27kernel: add a few patches for avoiding unnecessary skb reallocations - ↵nbd
significantly improves ethernet<->wireless performance with mac80211 based drivers git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31886 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: build images for DSL-274XB revision F1jogo
Build images for D-Link DSL-274XB revision F1. Flashing through original web UI as well as CFE works. Known issues: * wifi led inverted (on when wifi is off and vice cersa) * same issues as generic bcm6328 support git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31885 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add ath9k to atheros wifi profilejogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31884 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: enable bcm6328 support and required driversjogo
BCM6328 support is in a usable state, with the following issues * internal switch port not configurable * external phys not supported * broadcom wifis will probably not work correctly * and all other generic bcm63xx issues (so yes, still no ADSL) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31883 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add support for DSL-274XB rev F1jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31882 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: fix port state after network downjogo
bcm_enetsw_probe did not properly reset port states, resulting in connected ports staying disabled after bringing up the interface the second time. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31881 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add a fixup for ath9k devicesjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31880 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add support for the HSSPI controllerjogo
Add support for the HSSPI controller found on bcm6328 and SPI attached flash. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31879 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add preliminary support for bcm6328jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31878 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add flash type detectionjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31877 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: pad Speedport W303 V images to 4 MiBjogo
Prevents CFE from flashing to the second image offset. Fix up the rootfs length on first boot else CFE will complain. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31876 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add a default switch configuration for DSL-274XBjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31874 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: setup network config through uci-defaultsjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31873 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: move the board name workaround to /lib/brcm63xx.shjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31872 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: use the exact board id as board identification stringjogo
No need to keep the bcm63xx/ at the start or the chipid info at the end. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31871 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-24kernel: fix a warning in the connmark modulenbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31856 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23kernel: update linux 3.3 to 3.3.7juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31848 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23ar71xx: fix an insignificant typojuhosg
Patch from #11485. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31847 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23ar71xx: fix WLAN led for RB751U-2HnD and RB751G-2HnDjuhosg
Patch by Kamil Trzciński <ayufan@osk-net.pl> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31846 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23ar71xx: add support for TP-Link TL-MR3040juhosg
Support for TP-Link TL-MR3040. Power LED not working - always on red, after start should be green. Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31845 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23ramips: Add byte queue limits support to net/ethernet/ramips_main.cjuhosg
Add byte queue limits support to net/ethernet/ramips_main.c "Byte queue limits are a mechanism to limit the size of the transmit hardware queue on a NIC by number of bytes. The goal of these byte limits is too reduce latency (HOL blocking) caused by excessive queuing in hardware (aka buffer bloat) without sacrificing throughput." Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31844 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23ramips: Enable sysupgrade for Sitecom WL-351juhosg
Sysupgrade works just fine on my Sitecom WL-351 after adding this oneliner. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31843 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23linux/3.3: avoid recursive calling of mtd_writev in the block2mtd driverjuhosg
Should fix #11513. Tested with the x86/generic squashfs image within a VM. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31841 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-20lantiq: allow platforms with rt2x00 to override the mac address without ↵nbd
overriding eeprom, fixes bogus wlan mac address on arv4520 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31835 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-18kernel: merge a net-next fq_codel backlog handling fixnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31813 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-18omap24xx: add support for 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31810 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-18cns3xxx: add support for 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31809 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-06 03:36:54 +0000