summaryrefslogtreecommitdiff
path: root/target/linux/x86
AgeCommit message (Collapse)Author
2012-08-09Fix hard reset of alix/soekris hardware under heavy NIC loadjow
The following patch corrects a hard reset that occurs on alix and soekris net5501 hardware. Specifically, this is an issue with the via rhine NIC driver. Under periods of extreme load, the via rhine driver can cause a reset of the entire system. When this happens no output is seen on the console, the device simply reboots. This was reported in the following ticket: Consistent crash on Soekris NET5501 https://dev.openwrt.org/ticket/11882 I was able to reproduce the problem locally with numerous alix 2d13 platforms. Under heavy 64 byte frame size load from a Smartbits traffic generator, the alix hardware will hard reset in under 5 minutes. The same hardware, under the same load, on FreeBSD 9.0 does not reset. The patch below backports most of the via rhine changes from kernel 3.5. With OpenWrt trunk being on kernel 3.3.8, it seemed prudent to bring these changes in to avoid this serious issue. I've tested this heavily in my test environment and was able to keep the device stable under load for extended periods of time without any resets. Also, a nice side effect of this change is that it significantly raises the performance the platform. Without this patch the alix 2d13 can move approximately 29,000 packets per second at 64 byte frame sizes. After this patch the alix can move 52,000 packets per second at 64 byte frame sizes. I put this patch under the x86 patches as those are the only platforms with via rhine hardware that I'm aware of. If it needs to go some place else please let me know. Thanks, Adam Signed-off-by: Adam Gensler <openwrt@kristenandadam.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33072 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-07-25[package] make kmod-fb dependent on DISPLAY_SUPPORT and update targets ↵florian
accordingly git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32869 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-07-25[x86] move leds modules back to target modules.mkflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32851 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-07-25[x86] move i2c modules back to target modules.mkflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32850 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-07-25[x86] move more x86-specific modules back to target modules.mkflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32848 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-07-25[x86] move x86 specific ide/pata modules to x86' modules.mkflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32846 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-19[x86] Fix sysupgrade for squashfs, jffs2 and ext4 imagesacinonyx
* use 'fsync' with 'dd' for image writing * save config to boot partition git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32465 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-18optimize kernel config for kvm_guestjow
This patch enables few extra kernel options for the kvm_guest subtarget: - Tickless kernel to avoid timer ticks in idle guests, reduces CPU usage - Enable paravirtualization steal time support Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32436 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-18[kvm_guest] remove inittab overridejow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32422 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-15[x86] use ttyS0 @ 115200 baud as default for KVM guestsjow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32384 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-05[kernel] bump to 3.3.8blogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32055 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23kernel: update linux 3.3 to 3.3.7juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31848 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-18x86: remove support for old kernelsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31804 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-18x86: remove subtarget specific LINUX_VERSION overridesjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31803 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-18x86/ep80579: switch to 3.3juhosg
Also fix build errors in the ep80579-drivers package. Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31802 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-18x86/olpc: switch to 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31784 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-18x86: image: select bootscript images by default for OLPCjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31783 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-17x86/thincan: switch to 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31765 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-17x86/xen_domu: switch to 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31764 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-17x86/kvm_guest: switch to 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31763 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-17x86/generic: switch to 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31762 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-16x86/alix2: switch to 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31753 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-16x86/net5501: switch to 3.3juhosg
Compile tested only. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31752 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-16x86: sync 3.3 configsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31751 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-16x86: sync 3.2 configsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31750 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-16x86: sync 2.6.39 configsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31749 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-15linux: move certain disabled symbols to the generic configsjuhosg
* CONFIG_ARCH_DMA_ADDR_T_64BIT * CONFIG_ARCH_HAS_ILOG2_U32 * CONFIG_ARCH_HAS_ILOG2_U64 * CONFIG_ARCH_PHYS_ADDR_T_64BIT * CONFIG_ARCH_SUPPORTS_MSI * CONFIG_GENERIC_CPU_DEVICES * CONFIG_HWMON_DEBUG_CHIP * CONFIG_I2C_PXA_PCI * CONFIG_LEDS_GPIO * CONFIG_MINIX_FS_NATIVE_ENDIAN * CONFIG_MLX4_CORE * CONFIG_POWER_SUPPLY * CONFIG_POWER_SUPPLY_DEBUG * CONFIG_QUOTACTL * CONFIG_SDIO_UART * CONFIG_SENSORS_K10TEMP * CONFIG_SENSORS_SCH56XX_COMMON * CONFIG_SENSORS_VIA_CPUTEMP * CONFIG_SERIO_AMBAKMI * CONFIG_SERIO_I8042 * CONFIG_SERIO_LIBPS2 * CONFIG_SERIO_PCIPS2 * CONFIG_SERIO_RAW * CONFIG_SERIO_SERPORT * CONFIG_SPI_BITBANG * CONFIG_SPI_GPIO git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31737 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-14kernel: update linux 3.3 to 3.3.6juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31709 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-07kernel: update linux 3.3 to 3.3.5juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31645 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-30kernel: update linux 3.3 to 3.3.4juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31541 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-24kernel: update linux 3.3 to 3.3.3jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31460 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-24kernel: update linux 3.2 to 3.2.16jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31459 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-23x86: restore config-default, it is needed for 2.6.39juhosg
Reported-by: Thomas Heil <heil@terminal-consulting.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31452 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-21x86: remove 2.6.32 supportjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31415 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-17kernel: x86: also update subtarget kernel versionsjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31338 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-16[geos] bump to Linux v3.3.1jow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31314 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-12PATCH: Disable console terminal in Grub for alix2 targetjow
The alix2 target has the VGA console for grub enabled by default. This prevents the grub menu from appearing on bootup. It is disabled by default for the other embedded x86 platforms. This patch corrects that behavior for the alix2 target. Signed-off-by: Adam Gensler <openwrt@kristenandadam.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31270 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-10[x86] add missing Kernel symbol spotted by buildbotjow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31232 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-09kernel: update linux 3.2 to 3.2.14jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31222 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-27[x86] geos: add 'tc' and kmod-sched for bondingflorian
The Geos2 includes 2 ADSL+ interfaces, and as such it needs to have the TEQL scheduler for bonding. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31094 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-21Disable keyboard for x86 default config - revoke patch 30966 ryd
This was already fixed by commit 30309 and is part of generic x86 target. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31052 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-18[x86] alix2: add require crypto kmods (#10410)jow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30980 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-17Enable keyboard for x86ryd
This is required for qemu like descripted in here http://wiki.openwrt.org/doc/howto/qemu git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30966 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-25[x86] enable RTC_CLASS for Linux 3.2 and 3.3jow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30717 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-24config: deprecated symbol CONFIG_LEDS_GPIO_PLATFORMjow
CONFIG_LEDS_GPIO_PLATFORM went away a while ago. http://git.kernel.org/?p=linux/kernel/git/stable/linux-stable.git;a=commit;h=2bcc7ed5b83b0a59c6976476e8788675038fb11b Also, most platforms comment out CONFIG_LEDS_GPIO but not x86 for some reason. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30708 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-16[x86] Disable by default padding of imagesacinonyx
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30590 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-16[x86] Allow gzipping of squashfs images with padded jffs2 partitionacinonyx
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30589 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-16[x86] GZip only ext4 and padded imagesacinonyx
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30588 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-16[x86] Make gzipping of images configurable via menuconfigacinonyx
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30587 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-078139cp: backport patches to make driver stable againjow
List of patches that Jo-Philipp groveled out of git. Redux: defuzzed. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30366 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-15 15:32:24 +0000