summaryrefslogtreecommitdiff
path: root/target/linux/ramips/base-files
AgeCommit message (Collapse)Author
2012-05-29ramips: use the generic uci-default functions for initial LED setupjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-29ramips: WAN LED for D-Link DIR-300-B1juhosg
Add led devices for D-Link DIR-300-B1 WAN LED. Note that the GPIO state is also ANDed with the esw switch port 4 LED state, which is why I've set the amber LED to default-on. Closes: https://dev.openwrt.org/ticket/11326 Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> [ juhosg: - fix comment style in mach-dir-300-revb.c, - remove the PPP specific LED setup, not everyone uses a PPP connection on the WAN interface] git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31989 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27ramips: make rt2x00 firmware extraction quietjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31918 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23ramips: Enable sysupgrade for Sitecom WL-351juhosg
Sysupgrade works just fine on my Sitecom WL-351 after adding this oneliner. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31843 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-02ramips: W306R V2.0 - GPIO and Network fixesjuhosg
Fixed: GPIO typos and confirmed GPIO_BUTTON_RESET Fixed: Lan & Wan reversed: swaped "eth0.2" with "eth0.1" by removing a line(default is correct), and reversed the Lan/wan layout LLLLW to WLLLL. Added: image/Makefile now builds -factory.bin files. I am unsure of the accepted way to change the makefile but the name of the image needs to be 'linkn Kernel Image' in order to be accepted by the OEM firmware. Known issue: eth0 (internal switch i think has mac address: 00:11:22:33:44:55 but i think it should be same as the lan). Known issue: Pressing the reset button has no noticable effect, i would expect the router to boot failsafe if being pressed on boot, reboot if short press and reset all to default if long press. [juhosg: remove mtdlayout_W306R and use mtdlayout_4M instead] Signed-off-by: David Pearce <david_18051985@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31557 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-29ramips: rt305x: extract wifi eeprom and use the 8M template for the UR-336UNjuhosg
Patch-by: Lebedev Dmitry <lebedev@trendnet.ru> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31507 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-23ramips: rt305x: add support for the UR-336UN boardjuhosg
Patch-by: Lebedev Dmitry <lebedev@trendnet.ru> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31451 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-23ramips: rt305x: add support for the Asus WL-330N3G boardjuhosg
This patch adds support for the ASUS WL-330N3G Comparing to the WL-330N, It have 32MB ram, usb support and a bicolor led. The bi-color led is driven by 2 gpio. I don't know how to handle this, so I simply made 2 leds : one red, one blue. But the red light takes precedence over the blue one according to the chart below. r = led is red b = led is blue 0 = led is off xy= x->r for red, b for blue led, y->value of brightness in /sys/class/leds/x/brughtness initial state action led gpio state r0 b0 r0->r1 r r0 b0 r0 b0 b0->b1 b r0 b1 r1 b0 r1->r0 0 r0 b0 r1 b0 b0->b1 r r1 *b1* r1 b1 r1->r0 b r0 b1 r1 b1 b1->b0 r r1 b0 r0 b1 r0->r1 r r1 *b1* r0 b1 b1->b0 0 r0 r0 Signed-off-by: Frédéric Leroy <fredo@starox.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31450 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-21ramips: rt305x: add initial support for Tenda W306R V2.0juhosg
More device info at: http://wiki.openwrt.org/toh/tenda/w306r Signed-off-by: David Pearce <David_18051985@hotmail.com.au> [juhosg: fix checkpatch errors, remove kmod-phy and luci-ssl packages from the profile, change broken GPIO number] git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31396 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-29ramips: add support for the ARC FreeStation5 board, also fix WCR-150GN ↵jow
network setup while we're at it - thanks Pau Escrich <p4u@dabax.net> for the implementation git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31144 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-27ramips: rt305x: add add support for the Asus WL-330N boardjuhosg
[juhosg: reorder several lines in order to keep things sorted alphabetically] Signed-off-by: Frédéric Leroy <fredo@starox.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31100 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-04ramips: add support for unbranded XDX-RN502J boardjuhosg
This patch adds support for routers using a PCB marked XDX-RN502J V2.0, such as some unbranded routers like this: http://www.mediafire.com/?8acv87h6snn9fj6 http://www.mediafire.com/?do7xonw7scor4kn http://www.mediafire.com/?1ad49zvx3e7jyix http://www.mediafire.com/?i46cqiq66maa197 http://www.aliexpress.com/product-fm/516397994-Free-Shipping-300M-3G-WAN-Wireless-N-WiFi-USB-AP-Router-2-Antennas-wholesalers.html some reports also state the Aceex 22Y uses the same board. more information can be found in the following openwrt forum post https://forum.openwrt.org/viewtopic.php?id=34878 [juhosg: fix checkpatch warnings, use the GENERIC_4M template] Signed-off-by: bruno schwander <bruno@tinkerbox.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30809 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-04ramips: board support for Asus RT-N10+juhosg
[juhosg: fix indentation in platform scripts, and remove debug messages from 06_set_iface_mac] Signed-off-by: Patrick van Staveren <trick@vanstaveren.us> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30808 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-22ramips: merge identical switch configuration entriesjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30688 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-22ramips: use unified switch identifiers in uci-defaults/networkjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30687 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-22ramips: fix VLAN config of the RT-N15juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30686 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-19ramips: rt305x: add support for the Skyline SL-R7205 Wireless 3G routerjuhosg
[juhosg: - don't switch back to 2.6.39 - update config-3.2 - change machine id to SL-R7205 - reorder case entries in platform scripts - remove button hotplug script] Signed-off-by: Haipoh Teoh <hpteoh@ceedtec.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30645 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-16ramips: extract eeprom for the built-in wlan module on the RT-N56Ujuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30604 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-15[ramips] add Ralink V11ST-FE board supportflorian
This board is equipped with: - 4MB of NOR Flash - 32MB of SDRAM - IC+ IP175C switch - one Mini-PCI slot git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30561 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-14ramips: extract eeprom for the PCIe wlan module on the RT-N56Ujuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30529 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-13ramips: add preliminary support for the Asus RT-N56U boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30498 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-11ramips: load gpio-polled keys modulejuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30463 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-11ramips: fix Belkin F5D8235-v2 VLAN setupjuhosg
Signed-off-by: Roman Yeryomin <roman@advem.lv> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30452 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-11ramips: rt305x: add support for Accton WR6202 / SMCWBR11S-3GNjuhosg
This patch adds support for the Accton WR6202 Mini 3G broadband router. Full details for this device are available at http://www.awbnetworks.com/products03.php?Fullkey=19. This device is identical to the SMCWBR11S-3GN: http://www.smc-asia.com/products03.php?Fullkey=210 It's also worth noting that this board has a GPIO line to control the power to the USB port. [juhosg: - fix checkpatch warnings, - reorder Kconfig entry, - merge the sysupgrade patch, - add GPL header] Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30434 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-11ramips: rt305x: merge duplicated mac address setupjuhosg
Signed-off-by: Roman Yeryomin <roman@advem.lv> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30433 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-26ramips: add support for Sitecom WL-341v3 and other Sercomm IP1006RRv2 boardsjuhosg
This patch adds support for the Sitecom WL-341 v3 and other Sercomm IP1006RRv2 based boards for sysupgrade support and for the initial flash through pushbutton initiated recovery mode with the special partition table and fixes for the quirks and things required by the modified bootloader. There is a known bug, Wi-Fi is not working on my board probably because of the lack of RAM (the board only has 16MiB ram -- half of the normal amount for non rebadged versions, but there is an empty slot for another ram chip,) but I don't know for sure. The driver loads but hostapd fails to load so I think it's not related to the specific device except for the lack of RAM. Moreover, only 7 of the 11 onboard leds are confirmed working, it seems that one of the others is always on and the remaining ones are connected to the wireless card leds already recognized by OpenWrt [juhosg: reordered some parts in order to keep things sorted alphabetically] Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29910 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-24ramips: add user-space support for ALL0256Njuhosg
This adds uci-defaults and sysupgrade support for the ALL0256N. Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29883 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-23ramips: scripts updatesjuhosg
In this patch: * rename Argus leds to avoid underscores * rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235 * remove Belkin F5D8235 v1 status led defined as storage led (it was defined as usb led earlier, just in wrong place) - it should have router led as in v2 * add Argus, Sparklan and Belkin F5D8235 v2 status leds * add Belkin F5D8235 v1 and v2 usb leds * fix Belkin F5D8235 v2 network config generation and mac address axtraction * fix Sparklan board identification * add Sparklan usb led (this board doesn't have usb connector by default and the led is hidden also but if you are going to solder the connector then you'll see the led too) * add Sparklan network config generation and mac address extraction * fix empty string test in network script and... * ...sort case entries by the first board in the list Signed-off-by: Roman Yeryomin <roman@advem.lv> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29871 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-22ramips fix f5d8235-v1 diag LED supportjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29857 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-22ramips: add sysled and sysupgrade to wr512-3gnjuhosg
Patch from #10035. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29847 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-20ramips: sysupgrade for ESR-9753juhosg
This patch add sysupgrade for Engenius ESR-9753 Signed-off-by: Artur Wronowski <arteqw@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29824 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-28ramips: rt288x: add support for the Belkin F5D8235-4 v1 boardjuhosg
Patch-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29617 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-28ramips: rt305x: add support for the ALFA Networks W502U (R36) boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29615 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-27ramips: rt288x: add support for the Buffalo WLI-TX4-AG300N boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29612 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-23ramips: initial support for Sitecom WL-351 v1 002juhosg
This add support for the Sitecom WL-351 v1 002. In principle the Engenius ESR9850 should also work with this, but I don't have the hardware to test it. Since an external gigabit switch (RTL8366RB) is used, I had to modify the ramips_esw driver to add a 'bypass' mode, which just configures it to not filter the vlan tags. Also two initialization words (FCT2 and FPA2) are set to different values by u-boot than what the driver is using and it only seems to work correctly when they not overridden by the driver, so I added them to the platform specific data as reg_initval_fct2 and reg_initval_fpa2. With this wired lan works as expected, however I'm still having some trouble with the wireless lan: It only works after I rmmod & re-insmod rt2800pci and then reconfigure it in the webinterface, but not directly after rebooting. The symptom of this is wpad saying: Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1) Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN) Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated But wpa_supplicant on the client saying: Authentication with <wl351mac> timed out. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29604 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-23ramips: add support for the Senao/EnGenius ESR-9753 boardjuhosg
Signed-off-by: Artur Wronowski <arteqw@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29603 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-14ramips: add support for Omnima MiniEMBWiFi boardjuhosg
This patch adds support for the Omnima MiniEMBWiFi Ralink RT3050F based board. Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29533 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-06ramips: fix mac addresses on the DIR-300/600 boardsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29471 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05ramips: set mac addresses for the NBG-419Njuhosg
Based on a patch by Nerijus Baliunas <nerijus@users.sourceforge.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29454 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05ramips: set preinit interface mac on the hw550-3g boardjuhosg
Based on a patch by Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29453 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05ramips: use ramips_get_mac_* functions in the preinit scriptjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29452 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05ramips: move ramips_get_mac_* functions to lib/ramips.shjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29451 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05ramips: add ramips_ prefix to get_mac_{binary,nvram} functionsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29450 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05ramips: fix network configuration setupjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29448 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01ramips: enable sysupgrade on the RT-N15 boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29393 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01ramips: wrap long line in platform upgrade scriptjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29392 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01ramips: setup default network configuration for RT-N15juhosg
Based on a patch by Roman Yeryomin <roman@advem.lv> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29390 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01ramips: remove default network configuration, and generate that from ↵juhosg
uci-defaults git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29387 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01ramips: use /lib/functions/uci-defaults.shjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29386 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01ramips: simplify uci-defaults/network scriptjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29383 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-30 05:38:16 +0000