summaryrefslogtreecommitdiff
path: root/target/linux/generic/files/drivers
AgeCommit message (Collapse)Author
2013-09-25kernel: b53: add Register Access Bridge Registers (SRAB) interfacehauke
The SRAB interface is used on BCM4707 and BCM5301X SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38198 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-25kernel: create firmware partition from MyLoader partition parserjuhosg
This is in preparation for sysupgrade support for Compex devices. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38197 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-21kernel/3.10: add partition parser for Seama firmwaresjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38114 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-21kernel/3.10: add partition parser for uImage firmwaresjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38113 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-21kernel/3.10: add default partition name defines to mtdsplit.hjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38112 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-21kernel/3.10: add more helpers to the mtdsplit codejuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38111 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-21kernel/3.10: add separate rootfs partition parserjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38110 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-21kernel/3.10: move squashfs check from rootfs split code into a separate filejuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38109 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15kernel: b53: detect revision of BCM5325hauke
The revision is stored in a different register than it is in other Broadcom switches. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37995 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15kernel: b53: fix vlan write for BCM5325 revison 3+hauke
These switches are integrated in some recent BCM53XX and BCM47XX SoCs like the BCM53572. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37994 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-14kernel: b53: use hard coded switch reset gpio on some boards.hauke
The Linksys wrt310n v1 does not have a robo_reset config variable in nvram, but GPIO Pin 8 is the pin needed for resetting the external switch, Linksys hard coded it into their source code. Thank you Devastator for testing. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37988 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-14kernel: b53: add soft reset for BCM539x switcheshauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37987 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-05kernel: b53: support phy ids for BCM5365jogo
BCM5365 (and probably other older variants) use a different phy id, so the phy driver never attached for them. Fix this by adding the appropriate phy id to the fixup and the phy driver. Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37906 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-04kernel: b53: allow access the MIB counters on BCM5365hauke
b53_no_ops has no elements and b53_port_ops has one element, this makes the code access some random memory when trying to access the mib counter functions. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37895 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-02generic: remove linux version checks from myloader.cjuhosg
The myloader partition parser code uses ifdef wrappers to make the code usable on kernels below version 3.2. All targets are using kernel 3.3 at least so the wraper is not needed. Remove that. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37880 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-12rtl8367: add support for configuring the VLAN FIDnbd
Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37760 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01kernel: b53: use devm_gpio_request_one() to request gpiohauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37648 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01kernel: b53: add support for GPIO resethauke
This is needed for some switches used on bcm47xx SoCs like the one on the Asus RT-N66U. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37645 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-27strict_strtoul is obsolete, use kstrtoul insteadblogic
based on http://patchwork.openwrt.org/patch/3827/ Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37562 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-21kernel: Remove gpio-pwm patcheslars
There is no platform using the gpio-pwm driver, yet these patches break the generic PWM framework that is in upstream. So just remove them. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37490 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-19kernel: remove gpio_buttonsjogo
It hasn't been buildable for a long time, and there are no users of it anymore left as all of them have been switched to the upstream accepted version. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37436 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: use b53 phy driver for the switch in kernel 3.10hauke
This makes it possible to use swconfig to controll the switch. This was tested with devices using b43 and bgmac. This was not tested on devices using tg3. This does not support the adm switch used in some very old devices. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37304 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-04generic: add port mirroring/monitoring capability to rtl8366rb switchjuhosg
This patch adds swlib attributes to the RTL8366RB switch/PHY found in the TL-WR1043ND router that allow to mirror ethernet packets to a monitor port. Signed-off-by: Colin Leitner <colin.leitner@googlemail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36847 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30generic: ar8216: allow to specify SGMII config via platform datajuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36798 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30generic: ar8216: add get_port_link callbackjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36797 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30generic: ar8216: show chip revision in the kernel logjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36791 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-24generic: ar8216: add port mirroringluka
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both RX and TX traffic from LAN port 1 to LAN port 4: $ swconfig dev switch0 set enable_mirror_rx 1 $ swconfig dev switch0 set enable_mirror_tx 1 $ swconfig dev switch0 set mirror_monitor_port 4 $ swconfig dev switch0 set mirror_source_port 1 Signed-off-by: Colin Leitner <colin.leitner@googlemail.com> Tested-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36713 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-13kernel: add missing PHY ID for an AR8327 switch variantnbd
Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36630 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-09kernel: b53: use correct oops for bcm5365 switchhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36589 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-25generic: fix rtl8366_smi compile warningblogic
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports': drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36442 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-12[geneirc] fix rtl8366s OF bindingblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36323 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-09[ramips] unbreak portmapping - typo fixblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36293 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-09[swconfig] allow loading port maps from OFblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36283 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367: add compatible string with vendor prefixjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36230 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367b: fix rtl8367b_extif_init_ofjuhosg
* disable external interface if its property is not present * show an error message if the extif property is not valid * use proper error values intead of -1 * fix memory leak * wrap long lines Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36229 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367: allow to load extif config from OFjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36220 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367: fix a typo in MODULE_DEVICE_TABLE macrojuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36219 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367: add vendor prefix to the compatible stringjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36218 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-03[generic] add OF support to rtl8367b driverblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36159 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: start AR8327 switch from the probe routinejuhosg
The AR8327 switch gets its configuration from platform data or from the device-tree. This allows to start it from the probe routine. Doing so makes it usable with ethernet drivers which only connects to the PHY device when the ethernet interface is opened. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36050 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: add ar8xxx_start helperjuhosg
Move switch starting code into a separate function. This makes it usable from other places. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36049 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: add OF configuration support for AR8327juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36047 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: separate platform_data based AR8327 codejuhosg
Move platform_data specific configuration code into a separate routine. Do it in preparation for the upcoming OF support. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36046 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: don't use platform_data in ar8327_init_portjuhosg
Fetch the PORT_STATUS values in ar8327_hw_init and store those in a private data stucture for later use. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36045 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: move the ar8327_get_port_init_status functionjuhosg
It will be used in ar8327_probe routine. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36044 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: simplify and rename ar8327_config_portjuhosg
Return with the PORT_STATUS register value instead of writing that directly into the corresponding register. Also rename the function to ar8327_get_port_init_status. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36043 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: remove superfluous pdata checksjuhosg
The presence of the platform data is already verified in ar8327_hw_init, and the driver does not start without that anyway. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36042 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-21generic: b53: clear SM_SW_FWD_MODE unconditionally when enabling VLANjogo
Setting this bit stops BCM53125 (bgmac actually) from receiving any packets. This bit is cleared conditionally in b53_switch_reset and it seems the same is done in bcmrobo.c which never sets that bit again. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35723 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-21generic: b53: remove empty spacesjogo
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35722 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-17generic: ar8216: cleanup function/variable namesjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35642 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-15 19:13:05 +0000