summaryrefslogtreecommitdiff
path: root/target/linux/generic/files/drivers/net/phy
AgeCommit message (Collapse)Author
2013-11-09kernel: adm6996: add support for ADM6996L and GPIO interfacehauke
This patch makes it possible to use adm6996.c on first generation BCM47XX devices with ADM switches. The GPIO bit banging protocol implementation was copied from the old switch driver and adapted to this driver and changed to the mainline kernel GPIO interface. The ADM6996L is different from the ADM6996M which is supported, for both specs are available in the Internet. This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for the device. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38698 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-24kernel: make swconfig checkpath compliantflorian
Fix the warnings and errors reported by checkpatch on swconfig.c Signed-off-by: Florian Fainelli <florian@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38523 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-06kernel: b53: add switch name into printk when it fails.hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38307 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-25kernel: b53: add Register Access Bridge Registers (SRAB) interfacehauke
The SRAB interface is used on BCM4707 and BCM5301X SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38198 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15kernel: b53: detect revision of BCM5325hauke
The revision is stored in a different register than it is in other Broadcom switches. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37995 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15kernel: b53: fix vlan write for BCM5325 revison 3+hauke
These switches are integrated in some recent BCM53XX and BCM47XX SoCs like the BCM53572. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37994 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-14kernel: b53: use hard coded switch reset gpio on some boards.hauke
The Linksys wrt310n v1 does not have a robo_reset config variable in nvram, but GPIO Pin 8 is the pin needed for resetting the external switch, Linksys hard coded it into their source code. Thank you Devastator for testing. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37988 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-14kernel: b53: add soft reset for BCM539x switcheshauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37987 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-05kernel: b53: support phy ids for BCM5365jogo
BCM5365 (and probably other older variants) use a different phy id, so the phy driver never attached for them. Fix this by adding the appropriate phy id to the fixup and the phy driver. Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37906 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-04kernel: b53: allow access the MIB counters on BCM5365hauke
b53_no_ops has no elements and b53_port_ops has one element, this makes the code access some random memory when trying to access the mib counter functions. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37895 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-12rtl8367: add support for configuring the VLAN FIDnbd
Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37760 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01kernel: b53: use devm_gpio_request_one() to request gpiohauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37648 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01kernel: b53: add support for GPIO resethauke
This is needed for some switches used on bcm47xx SoCs like the one on the Asus RT-N66U. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37645 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-27strict_strtoul is obsolete, use kstrtoul insteadblogic
based on http://patchwork.openwrt.org/patch/3827/ Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37562 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: use b53 phy driver for the switch in kernel 3.10hauke
This makes it possible to use swconfig to controll the switch. This was tested with devices using b43 and bgmac. This was not tested on devices using tg3. This does not support the adm switch used in some very old devices. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37304 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-04generic: add port mirroring/monitoring capability to rtl8366rb switchjuhosg
This patch adds swlib attributes to the RTL8366RB switch/PHY found in the TL-WR1043ND router that allow to mirror ethernet packets to a monitor port. Signed-off-by: Colin Leitner <colin.leitner@googlemail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36847 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30generic: ar8216: allow to specify SGMII config via platform datajuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36798 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30generic: ar8216: add get_port_link callbackjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36797 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-30generic: ar8216: show chip revision in the kernel logjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36791 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-24generic: ar8216: add port mirroringluka
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both RX and TX traffic from LAN port 1 to LAN port 4: $ swconfig dev switch0 set enable_mirror_rx 1 $ swconfig dev switch0 set enable_mirror_tx 1 $ swconfig dev switch0 set mirror_monitor_port 4 $ swconfig dev switch0 set mirror_source_port 1 Signed-off-by: Colin Leitner <colin.leitner@googlemail.com> Tested-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36713 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-13kernel: add missing PHY ID for an AR8327 switch variantnbd
Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36630 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-09kernel: b53: use correct oops for bcm5365 switchhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36589 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-25generic: fix rtl8366_smi compile warningblogic
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports': drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36442 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-12[geneirc] fix rtl8366s OF bindingblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36323 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-09[ramips] unbreak portmapping - typo fixblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36293 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-09[swconfig] allow loading port maps from OFblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36283 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367: add compatible string with vendor prefixjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36230 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367b: fix rtl8367b_extif_init_ofjuhosg
* disable external interface if its property is not present * show an error message if the extif property is not valid * use proper error values intead of -1 * fix memory leak * wrap long lines Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36229 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367: allow to load extif config from OFjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36220 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367: fix a typo in MODULE_DEVICE_TABLE macrojuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36219 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06generic: rtl8367: add vendor prefix to the compatible stringjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36218 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-03[generic] add OF support to rtl8367b driverblogic
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36159 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: start AR8327 switch from the probe routinejuhosg
The AR8327 switch gets its configuration from platform data or from the device-tree. This allows to start it from the probe routine. Doing so makes it usable with ethernet drivers which only connects to the PHY device when the ethernet interface is opened. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36050 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: add ar8xxx_start helperjuhosg
Move switch starting code into a separate function. This makes it usable from other places. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36049 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: add OF configuration support for AR8327juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36047 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: separate platform_data based AR8327 codejuhosg
Move platform_data specific configuration code into a separate routine. Do it in preparation for the upcoming OF support. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36046 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: don't use platform_data in ar8327_init_portjuhosg
Fetch the PORT_STATUS values in ar8327_hw_init and store those in a private data stucture for later use. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36045 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: move the ar8327_get_port_init_status functionjuhosg
It will be used in ar8327_probe routine. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36044 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: simplify and rename ar8327_config_portjuhosg
Return with the PORT_STATUS register value instead of writing that directly into the corresponding register. Also rename the function to ar8327_get_port_init_status. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36043 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15generic: ar8216: remove superfluous pdata checksjuhosg
The presence of the platform data is already verified in ar8327_hw_init, and the driver does not start without that anyway. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36042 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-21generic: b53: clear SM_SW_FWD_MODE unconditionally when enabling VLANjogo
Setting this bit stops BCM53125 (bgmac actually) from receiving any packets. This bit is cleared conditionally in b53_switch_reset and it seems the same is done in bcmrobo.c which never sets that bit again. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35723 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-21generic: b53: remove empty spacesjogo
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35722 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-17generic: ar8216: cleanup function/variable namesjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35642 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-17generic: ar8216: rename struct ar8216_priv to ar8xxx_privjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35641 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-14generic: ar8216: move PHY4 RGMII workaround code out of the loopjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35603 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-14generic: ar8216: register the switch from the probe routinejuhosg
Currently the switch gets registered when an ethernet driver connects to a PHY of the switch. This method does not work with the ethernet drivers which are connecting to the PHY from their ndo_open callback. With those ethernet drivers, the driver tries to register the switch each time when the etherned device is opened and this causes a deadlock. Move the switch registration into the probe routine to fix this problem. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35602 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11ar8216: remove superfluous code from ar8216_config_initjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35562 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11generic: ar8216: don't use ethernet device name in register_switchjuhosg
The switches are accessed via an MDIO bus. Set the alias to the name of the MDIO bus, and show that in the message along with the name of the switch switch device. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35560 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11generic: ar8216: reuse the private data from ar8216_probejuhosg
The private data of the switch is already allocated in ar8216_priv, assign that to each PHY on the same MDIO bus. Also remove the redundant code from ar8216_config_init. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35559 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-11generic: ar8216: use phydev instead of pdev everywherejuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35555 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.46.0) at 2024-12-25 20:10:24 +0000