summaryrefslogtreecommitdiff
path: root/target/linux/brcm63xx
AgeCommit message (Collapse)Author
2012-07-03[brcm63xx] refresh patchesflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32581 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-29[brcm63xx] fix watchdog and rng drivers section mismatch (#11767)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32522 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-27[brcm63xx] fix SPI clock frequency selectionflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32512 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-17[brcm63xx] fix SPI message control handling for BCM6338/6348florian
BCM6338 and BCM6338 have their MSG_CONTROL register width of 8-bits instead of 16-bits. We were previously using a 16-bits write which corrupted the first byte of the TX FIFO. Also the message type was always set to Full-duplex even in the case of half-duplex messages. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32409 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-11bcm63xx: readd accidentially dropped ignore_oc in ehci driverjogo
fixes overcurrent warning spam on 3.3 kernels for bcm63xx again. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32221 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06[brcm63xx] fix 553-board_96348w3.patch patch wrt gpio-keys-polledflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32096 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06[brcm63xx] fix alarm led color for board 96348A-122florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32089 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06[brcm63xx] add 96348w3 board (#10764)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32088 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06[brcm63xx] update livebox board support (#8677)florian
Merge most fixes from #8677: - add basic hardware detection of Livebox Blue 5g revisions - register leds and gpio buttons - fix boot address location - properly parse mac addresses Plus some more fixes: - make board_livebox.c more in line with board_bcm963xx.c git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32087 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06[brcm63xx] fix leds naming for all bcm63xx boardsflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32086 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06[brcm63xx] backport upstream spi-bcm63xx fixesflorian
* message pump conversion * not using stopping state * setting spi driver mode bits git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32078 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06[brcm63xx] increase led number in patch 301-led_count.patchflorian
So that board patches are only touching board-related code git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32076 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-05[brcm63xx] fix board patches so that new boards are withing appropriate ifdefflorian
Some new board definitions were added within the #ifdef CONFIG_CPU_6338 section while some other were added within #ifdef CONFIG_CPU_6345, fix this git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32060 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-05[brcm63xx] fix bisectability of patch 303-spi-board-info.patchflorian
It uses spi_register_board_info() from linux/spi/spi.h but does not include it explicitely. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32058 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-05[kernel] bump to 3.3.8blogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32055 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-04bcm63xx: fix ethernet on 96328avng and 963281TANjogo
The internal switch did not get registered. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32041 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-30bcm63xx: build images for 6328 reference boards with various flash sizesjogo
Build images for 96328avng and 963281TAN (untested) for three different flash sizes: 4MB, 8MB, and 16MB. Known issues: * Button setup unknown, thus no fail-safe available. * All other BCM6328 and BCM63XX issues git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32004 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-30bcm63xx: readd accidentially dropped network config for SPW303Vjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32003 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: build images for DSL-274XB revision F1jogo
Build images for D-Link DSL-274XB revision F1. Flashing through original web UI as well as CFE works. Known issues: * wifi led inverted (on when wifi is off and vice cersa) * same issues as generic bcm6328 support git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31885 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add ath9k to atheros wifi profilejogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31884 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: enable bcm6328 support and required driversjogo
BCM6328 support is in a usable state, with the following issues * internal switch port not configurable * external phys not supported * broadcom wifis will probably not work correctly * and all other generic bcm63xx issues (so yes, still no ADSL) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31883 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add support for DSL-274XB rev F1jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31882 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: fix port state after network downjogo
bcm_enetsw_probe did not properly reset port states, resulting in connected ports staying disabled after bringing up the interface the second time. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31881 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add a fixup for ath9k devicesjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31880 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add support for the HSSPI controllerjogo
Add support for the HSSPI controller found on bcm6328 and SPI attached flash. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31879 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add preliminary support for bcm6328jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31878 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add flash type detectionjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31877 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: pad Speedport W303 V images to 4 MiBjogo
Prevents CFE from flashing to the second image offset. Fix up the rootfs length on first boot else CFE will complain. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31876 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: add a default switch configuration for DSL-274XBjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31874 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: setup network config through uci-defaultsjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31873 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: move the board name workaround to /lib/brcm63xx.shjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31872 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27bcm63xx: use the exact board id as board identification stringjogo
No need to keep the bcm63xx/ at the start or the chipid info at the end. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31871 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23kernel: update linux 3.3 to 3.3.7juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31848 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-15linux: move certain disabled symbols to the generic configsjuhosg
* CONFIG_ARCH_DMA_ADDR_T_64BIT * CONFIG_ARCH_HAS_ILOG2_U32 * CONFIG_ARCH_HAS_ILOG2_U64 * CONFIG_ARCH_PHYS_ADDR_T_64BIT * CONFIG_ARCH_SUPPORTS_MSI * CONFIG_GENERIC_CPU_DEVICES * CONFIG_HWMON_DEBUG_CHIP * CONFIG_I2C_PXA_PCI * CONFIG_LEDS_GPIO * CONFIG_MINIX_FS_NATIVE_ENDIAN * CONFIG_MLX4_CORE * CONFIG_POWER_SUPPLY * CONFIG_POWER_SUPPLY_DEBUG * CONFIG_QUOTACTL * CONFIG_SDIO_UART * CONFIG_SENSORS_K10TEMP * CONFIG_SENSORS_SCH56XX_COMMON * CONFIG_SENSORS_VIA_CPUTEMP * CONFIG_SERIO_AMBAKMI * CONFIG_SERIO_I8042 * CONFIG_SERIO_LIBPS2 * CONFIG_SERIO_PCIPS2 * CONFIG_SERIO_RAW * CONFIG_SERIO_SERPORT * CONFIG_SPI_BITBANG * CONFIG_SPI_GPIO git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31737 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-14kernel: update linux 3.3 to 3.3.6juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31709 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-07kernel: update linux 3.3 to 3.3.5juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31645 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-06bcm63xx: fix a race between PCI bus scan and fallback sprom registrationjogo
The fallback sprom handler was installed too late, resulting in ssb failing to get a valid sprom on some devices. Fixes #11384. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31638 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-02[brcm63xx] use a define for the poll and debounce intervalflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31550 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-30kernel: update linux 3.3 to 3.3.4juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31541 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-27[brcm63xx] switch to gpio-keys-polledflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31491 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-24bcm63xx: drop linux 3.2 supportjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31464 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-24bcm63xx: drop linux 3.0 supportjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31463 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-24bcm63xx: switch kernel to 3.3jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31462 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28bcm63xx: enable bcm6368 for linux 3.3 and build imagesjogo
Only build bcm6368 images when building for linux 3.3. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31133 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28bcm63xx: add initial support for bcm6368 boardsjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31132 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28bcm63xx: add driver for the internal hw trng on bcm6368jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31131 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28bcm63xx: replace SPI driver with latest upstream versionjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31130 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28bcm63xx: add ethernet support for bcm6368jogo
Add basic support for the internal ethernet switch on bcm6368. It behaves as a dumb switch for now, but allows basic connectivity. Also drop the ethernet patch for bcm6345 for now, it needs rework. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31129 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28bcm63xx: add missing bits from extirq supportjogo
Add missing external IRQ code parts for older chips in the new code. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31128 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28bcm63xx: reorder patchesjogo
Reorder patches for a clearer distinction between the purposes of the different patches. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31127 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-06 11:38:57 +0000