summaryrefslogtreecommitdiff
path: root/target/linux/brcm63xx/image
AgeCommit message (Collapse)Author
2010-12-10[brcm63xx] Fixed Comtrend CT536_CT5621 board settings. These boards are ↵cshore
based on the 96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24442 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07[brcm63xx] boards: Added GW6x00 fixups and GPIOs. The GW6200 GPIOs are ↵cshore
different than the reference design 96348GW so we use fixup to allow us to define the correct ones, also the GW6000 has no GPIO-controlled leds. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24305 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28[brcm63xx] image Makefile: Corrected router imagename length limiting. ↵cshore
Thanks KanjiMonster for reminding me. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24191 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28bcm63xx: Add support for the T-Com Speedport W 500V.cshore
Add support for the T-Com Speedport W 500V using a special tagged image as it identifies itself as a 96348GW, but has some gpios wired differently, and also has only one ethernet port without a switch attached to it. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24190 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28bcm63xx: Add board id override fixup.cshore
Add a fixup for the kernel to check the bcm tag of the image for a boardid in the information1 field, and use that instead of the supplied one by cfe. This is triggered by a + at the start of the information1 field. Also modify the image generation to generate apropriately tagged images. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24189 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28bcm63xx: Finalize support for DSL-274xB, rev C2.cshore
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition, resulting in a kernel panic on boot. This patch adds it, and also renames the generated image name to properly reflect that it is for the revision C2, and for both the DSL-2740B and DSL-2741B. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24188 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-24[brcm63xx] image Makefile: Removed extraneous tab from Image/LimitName16 ↵cshore
macro definition. The solves the strange whitespace in front of the image name in the info1 section git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24127 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-23[brcm63xx] image: Limited image name put into the info1 field to 16 ↵cshore
characters and eliminted the OpenWRT revision. This makes using the image (router) name as the board name possible, so that boards with same real boardid but different GPIOs can be detected and the correct GPIOs used. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24118 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-19[brcm63xx] Initial support for Telsey CPVA642 boards (no vlans, no DSL, GPIO ↵cshore
led/buttons not known). git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24040 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-16[tools/firmware-utils] imagetag: Significantly updated brcm63xx imagetag ↵cshore
writing tool. * Rewrote commandline parsing code using gengetopt - We now get long options - We have more options including use of the info section for board information (e.g. to add the same boardid but different GPIOs on different routers) * Added back the ability to write stock images (this is useful, for example, when copying the firmware from the in-memory flash, and then being able to create an image that will let you revert to/test stock firmware * Fixed copying of CRCs to use memcpy instead of strncpy (strncpy stops at 0) * Added ability to use all sections of the imagetag, including custom magic signatures (e.g. for the Telsey router I'm adding soon), info sections, and reserved sections * Added putting the router type (as defined in the image generating Makefile) into the info1 section and the filesystem type in the info2 section. This will be used by mtd (when I add the code) to return the name of image used to flash this router. (As requested by Jo, as well as being useful for same boardid different board scenario described above). git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-04-12define a shared IMG_PREFIX variable used as a basename for image files, it ↵nico
contains board & subtarget infos (if appropriate) allowing subtargets to share the same bin directory without overwriting each other's files git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20834 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-04-01[brcm63xx] flashmap and image generation: reduced union bcm_tag to a single ↵florian
struct combining the elements so that it is no longer necessary to create an openwrt-only tagid and tagcrc, and elimate the tagid detection and switch statements which made dealing with imagetags overly complicated, especially since the logic would need analogs in all code that touched the imagetag. Patch from cshore. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20652 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-02-28[brcm63xx] build images for RG100A (bcm6358-based boards) (#6755)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@19894 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-10-29[brcm63xx] do not generate trx images, this is uselessflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@18204 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-08-09[brcm63xx] add support for the Pirelli AG226G board (#5337)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@17190 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-07-31[brcm63xx] generate images for RTA1025W_16-based routers (#5594)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@17058 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-06-26[brcm63xx] generate images for the bcm6338wflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16566 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-06-18[brcm63xx] add imagetag support for BT Voyager 2500V, patch from Daniel ↵florian
Dickinson (#5364) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16506 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-06-17[brcm63xx] generate experimental images for bcm6338 boards, thanks to Daniel ↵florian
Dickinson git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16490 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-06-10[brcm63xx] use build system REVISION variable (#5317)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16400 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-06-10The attached patch adds building of firmwareflorian
images for more routers based on the brcm63xx chipset. Signed-Off By: Daniel Dickinson <crazycshore@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16396 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-06-09[brcm63xx] rework imagetag firmware generator and MTD partition parser to ↵florian
accomodate with all known imagetag versions from Broadcom and vendors, patch from Daniel Dickinson (fixes #4987). git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16393 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-04-19[brcm63xx] make images that can be flashed using the stock firmware web ↵florian
interface, thanks to Anselmo Luginbuhl and Daniel Dickinson (#4909, #4943) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15253 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-04-17get rid of $Id$ - it has never helped us and it has broken too many patches ;)nbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15242 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-04-07[brcm63x] imagetag's -k argument is expected to be hexadecimal instead of ↵florian
decimal (#4885) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15133 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-03-16[brcm63xx] add the CFE offset command line option to the imagetag utility, ↵florian
closes (#4366) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@14896 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-03-12[brcm63xx] add support for AGPF-S0 (Pirelli Alice Gate VoIP 2 Plus Wi-Fi) #4366florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@14850 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-01-31[brcm63xx] add support for user9102 boards (#4537)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@14305 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-01-29[brcm63xx] generate images for old CFE based boards like the Davolink DV201florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@14264 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-12-12Build images for Inventel Liveboxflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13616 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-12-10Fix typo, we are not building for the DG834G (ar7) but the DG834GT (brcm6348)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13588 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-12-10Add support for Sagem F@ST2404 (#4332)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13583 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-12-07Add support for bcm96348gw10 (Netgear DG834GT) (#4319)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13540 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-11-20Generate valid images for the bcm96348gw boardflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13298 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-11-15This patch is for broadcom 96348GW-11 boards, to get USB and Ethernet ↵florian
working. Also it patches mtd map driver for bcm96xx boards to be sure that CFE1CFE1 code is detected when booting from CFE. (#4201) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13213 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-10-20Add definitions for bcm96350vw, add back bcm63xx mtd driver, be careful when ↵florian
testing with 8MB devices git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13015 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-05-18bcm963xx: image generation using image taggernbd
This adds CFE tagged image generation in the BCM963xx target image Makefile. It has to generate its own LZMA compressed kernel because CFE is a LZMA nazi. It also seems that the Broadcom image tagger as well as CFE use AdvanceCOMP, which is based on a slightly older LZMA SDK. Anyways, some of the code is GPL, some of it is LGPL, so it might be that Broadcom owes some sources. Also, LZMA has a bug which causes it to generate different output when you are using stdin / stdout compared to plain files. I've just worked around the issue by using plain files. Signed-off-by: Axel Gembe <ago@bastart.eu.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11171 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-05-18bcm963xx: fix load address / kernel entrynbd
Current kernels have the same kernel entry as load address, so just set them like this. Also, the BCM963xx uses 0x80010000 as its load address, so use this too. Signed-off-by: Axel Gembe <ago@bastart.eu.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11169 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-05-09enable proper PCI & USB support detection at config-time by disabling ↵nico
CONFIG_PCI & CONFIG_USB entries in generic/config and enabling them on targets where appropriate git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11097 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-04-01brcm63xx image generation cleanups (#3169)florian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@10703 3c298f89-4303-0410-b956-a3cf2f4a3e73
2007-11-10make the image filenames a bit shorternbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@9533 3c298f89-4303-0410-b956-a3cf2f4a3e73
2007-09-06strip the kernel version suffix from target directories, except for brcm-2.4 ↵nbd
(the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@8653 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-15 05:24:45 +0000