openwrt.git - OpenWRT with patches for F@ST2504n board

Age	Commit message (Collapse)	Author
2010-12-10	[brcm63xx] Fixed Comtrend CT536_CT5621 board settings. These boards are ↵	cshore
	based on the 96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24442 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07	[brcm63xx] boards: Added GW6x00 fixups and GPIOs. The GW6200 GPIOs are ↵	cshore
	different than the reference design 96348GW so we use fixup to allow us to define the correct ones, also the GW6000 has no GPIO-controlled leds. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24305 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07	[brcm63xx] Remove patch 140-new_bcm96348gw_leds because it is really the ↵	cshore
	GW6200 leds, not the generic 96348GW. Another commit will add the GW6200 specific boardid and leds. This removal reverts the 96348GW leds to the reference design GPIOs. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24302 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-06	[brcm63xx] base-files: Added the preinit information for reset button and ↵	cshore
	preinit indication led, and preinit interface git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24276 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28	bcm63xx: Add support for the T-Com Speedport W 500V.	cshore
	Add support for the T-Com Speedport W 500V using a special tagged image as it identifies itself as a 96348GW, but has some gpios wired differently, and also has only one ethernet port without a switch attached to it. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24190 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28	bcm63xx: Finalize support for DSL-274xB, rev C2.	cshore
	The DSL-2740B/DSL-2741B rev C2 support was missing the board definition, resulting in a kernel panic on boot. This patch adds it, and also renames the generated image name to properly reflect that it is for the revision C2, and for both the DSL-2740B and DSL-2741B. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24188 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28	bcm63xx: Don't hardcode the switch ethernet interface in preinit.	cshore
	Currently eth1 is hardcoded as the expected interface switches in diagmode. This patch replaces the eth1 with the ifname, and also directly tests if the interface specified by ifname has a switch attached. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24186 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-02	[brcm63xx] base-files: brcm63xx.sh: Added comtrend (96348GW-11) to routers ↵	cshore
	with buttons and leds on preinit git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22465 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-05-30	brcm63xx: Fixed vlan packet leakage in preinit for known devices with a ↵	cshore
	switch on eth1 (currently only 96348GW - Tecom 6x00) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21629 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-05-30	brcm63xx: Added preinit reset button module loading for devices known to ↵	cshore
	support it and for which /lib/brcm63xx.sh has the definitions (currently only 96348GW - Tecom 6x00) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21628 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-05-30	brcm63xx: Added preinit board-type detection (currently only 96348GW - Tecom ↵	cshore
	6x00) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21626 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-05-17	[brcm63xx] add support for sysupgrade (#5117)	florian
	git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15900 3c298f89-4303-0410-b956-a3cf2f4a3e73