| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26959 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Signed-off-by: Adrian Feliks <mexit@o2.pl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26958 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26878 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26876 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
based on the 96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24442 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
different than the reference design 96348GW so we use fixup to allow us to define the correct ones, also the GW6000 has no GPIO-controlled leds.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24305 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
GW6200 leds, not the generic 96348GW. Another commit will add the GW6200 specific boardid and leds. This removal reverts the 96348GW leds to the reference design GPIOs.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24302 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
preinit indication led, and preinit interface
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24276 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24190 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24188 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Currently eth1 is hardcoded as the expected interface switches in diagmode.
This patch replaces the eth1 with the ifname, and also directly tests if
the interface specified by ifname has a switch attached.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24186 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
with buttons and leds on preinit
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22465 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
switch on eth1 (currently only 96348GW - Tecom 6x00)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21629 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
support it and for which /lib/brcm63xx.sh has the definitions (currently only 96348GW - Tecom 6x00)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21628 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
6x00)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21626 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15900 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
