summaryrefslogtreecommitdiff
path: root/target/linux/brcm63xx/base-files/etc
AgeCommit message (Collapse)Author
2010-12-26base-files: Added uci-defaults script to run mtd fixtrx on firstboot for ↵cshore
devices that need it. Signed-off-by: Daniel Dickinson <daniel@cshore.neomailbox.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24836 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-10[brcm63xx] Fixed Comtrend CT536_CT5621 board settings. These boards are ↵cshore
based on the 96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24442 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-06[bcm63xx] base-files: Added network defconfig because board only has one ↵cshore
ethernet (4-port switch) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24273 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28bcm63xx: Add support for the T-Com Speedport W 500V.cshore
Add support for the T-Com Speedport W 500V using a special tagged image as it identifies itself as a 96348GW, but has some gpios wired differently, and also has only one ethernet port without a switch attached to it. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24190 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28bcm63xx: Finalize support for DSL-274xB, rev C2.cshore
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition, resulting in a kernel panic on boot. This patch adds it, and also renames the generated image name to properly reflect that it is for the revision C2, and for both the DSL-2740B and DSL-2741B. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24188 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28bcm63xx: Allow 'colored' power leds.cshore
Since some devices have more than one power led, they might be separated by their color in the name. To also allow them to be on after leaving preinit, set any status led starting with 'power' to on instead of only those with the exact name of 'power'. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24187 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28bcm63xx: Add defconfigs.cshore
Port the mechanism for different default configurations from ar71xx and use the old configuration as the default configuration. This should have no functional differences to before. While we are at it, remove the obsolete nat option. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24185 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-02[brcm63xx]: base-files: diag.sh: For power button as preinit status led, end ↵cshore
with led left on, not off git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22466 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-05-30brcm63xx: Added LED code for preinit (/etc/diag.sh) for 96348GW (Tecom 6x00)cshore
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21627 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-07-18[brcm63xx] we are using the default-on trigger for power LEDs, no need to ↵florian
change their state from userspace git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16892 3c298f89-4303-0410-b956-a3cf2f4a3e73
2009-07-18[brcm63xx] register GPIO-connected LEDs for known boardsflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@16887 3c298f89-4303-0410-b956-a3cf2f4a3e73
2008-11-26Make 4-port LAN and 1 port wan configurations workflorian
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@13362 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-26 01:37:49 +0000