summaryrefslogtreecommitdiff
path: root/target/linux/brcm47xx
AgeCommit message (Collapse)Author
2013-11-09brcm47xx: add detection for Linksys WRT54GS V1hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38700 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-09brcm47xx: register ADM6996L switchhauke
This patch makes it possible to use adm6996.c on first generation BCM47XX devices with ADM switches. This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for the device. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38699 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-05brcm47xx: fix detection of Asus RT-N12B1 and Netgear WNR3500Lhauke
This closes #14367 and #14328. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38656 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-05kernel: update 3.10 to 3.10.18juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38652 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-25brcm47xx: b44: fix error handling for dummy phy creationhauke
When the mdio bus is unregistered the newly created phy will also be unregistered and freed. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38539 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-25brcm47xx: b44: add dummy phy device if we do not find anyhauke
On some devices with e.g. a BCM2535F switch the second MAC is used, but we can not find a phy under all addresses between 0 and 31, 0xffffffff is returned as phy id. If we can not find a phy at the expected address create a dummy one. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38538 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-23kernel: update 3.10 to 3.10.17juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38506 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-22brcm47xx: b44: detect external phy by bit set in DevControl registerhauke
Without this patch we treated only phy addr 30 as an external phy, but there is a register to check that. Now we do not have to try to reset the switch to check for an external switch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38502 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-13brcm47xx: activate ARP daemon supporthauke
This just add some bytes to the kernel and is activated on other targets. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38388 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-13kernel: update kernel to 3.10.15hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38384 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-13brcm47xx: fix detection of some boardshauke
This adds some more boards. This fixes parts of #14316 and #14133. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38383 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-07brcm47xx: Cocci spatch "noderef"hauke
sizeof when applied to a pointer typed expression gives the size of the pointer. Found by coccinelle spatch "misc/noderef.cocci" Signed-off-by: Thomas Meyer <thomas@m3y3r.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38312 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-07brcm47xx: move clock detection patcheshauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38311 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-06brcm47xx: move and rename nvram gpio patchhauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38310 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-06brcm47xx: update early printk patcheshauke
Early printk was disabled because it caused hangs on some devices, the old patches were using the CFE console now we use the normal serial console, it is at a constant address. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38309 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-06brcm47xx: update board detection patcheshauke
Add patches like they are currently in the mainline mips tree and add some more pending patches for board detection. * Now the board name is shown under machine in /proc/cpuinfo. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38308 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-06brcm47xx: b44: fix some problems with the phyhauke
* do not try initialize a unused phy * some improvements to the phylib patch * do not turn the phy off when mac is off Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38306 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-02brcm47xx: add support for ipv6 in default network confighauke
Modify /etc/init.d/netconfig to use UCI defaults for building the default network config, which includes appropriate defaults for IPV6. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38294 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-02kernel: bgmac: move other bgmac patches to generichauke
The bgmac driver will be used on the brcm47xx and the bcm53xx target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38289 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-02kernel: bgmac: move bgmac patches already applied in mainline kernel to generichauke
The bgmac driver will be used on the brcm47xx and the bcm53xx target. These are only the patches already applied in current net-next/master branch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38288 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-27kernel: update 3.10 to 3.10.13juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38228 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-25kernel: b53: add Register Access Bridge Registers (SRAB) interfacehauke
The SRAB interface is used on BCM4707 and BCM5301X SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38198 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-18brcm47xx: b44: bgmac: some small changes to the phylib patcheshauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38044 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-18brcm47xx: bgmac: b44: add support for Byte Queue Limitshauke
This adds support for Byte Queue Limits in bgmac and b44, now it is possible to use more advanced network queue control algorithms. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38038 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-18brcm47xx: update the clock fixes for BCM5354 hauke
This updates the patches for BCM5354 to the version send for upstream Linux inclusion. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38037 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-18brcm47xx: update board detection patcheshauke
This is now the version which was send for mainline Linux kernel inclusion. The data needed to detection a board is now stored in init data. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38036 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-18brcm47xx: add detection for Linksys E900 V1hauke
Thank you Rafał for the data. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38035 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: Add support for Huawei E970hauke
This patch adds support for Huawei E970 wireless gateway devices. It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV. E960/B970 should work too, from what I know it's basically the same hardware. The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem. It uses a hardware watchdog which needs GPIO-7 to be toggled at least every 1-2 seconds. This patch uses gpio_wdt module (see my previous patch today) to take care of this. Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset button, image to be used for upgrade from OEM firmware's web interface Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970> Issue: * lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog reset during kernel decompress. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: add detection for Phicomm M1hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38009 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: detect Linksys E1200 V2hauke
This adds detection for Linksys E1200 V2 Thank you Lightsword and Rafał. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38006 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: mtd: bcm47xxpart: detect "factory" partitionhauke
A new type of partition with magic FCTY was found on Huawei E970: 46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290| Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38005 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: bgmac: implement unaligned addressing for DMA rings that support ithauke
This is important patch for new devices that support unaligned addressing. That devices suffer from the backward-compatibility bug in DMA engine. In theory we should be able to use old mechanism, but in practice DMA address seems to be randomly copied into status register when hardware reaches end of a ring. This breaks reading slot number from status register and we can't use DMA anymore. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38004 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: add detection code for Huawei E970hauke
This is based on a patch by Mathias Adam. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38001 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15kernel: update 3.10 to 3.10.12juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38000 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: bgmac: allow bigger et_swtype nvram variablehauke
Without this patch it is impossible to read et_swtype, because the 1 byte space is needed for the terminating null byte. Now it should be possible to read decimal and hex vars of max 8 bit. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37999 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: mtd: bcm47xxpart: detect block aligned Squashfs partitionhauke
Most of the bcm47xx devices use TRX format for storing kernel and some partition like Squashfs or JFFS2. This is pretty flexible solution, CFE (the bootloader) just writes (and later boots) TRX at some hardcoded place and paritions can vary in the size. However some devices don't use TRX format. Very recently we have discovered ZTE H218N that has kernel and rootfs partitions at some "random" places. This patch allows Linux find a rootfs partition after installing custom image with a CFE bootloader. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37998 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: update board detection patchhauke
* Use different structs depending on the number of nvram variables to check. * Add detection of ZTE H218N, this closes #14151. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37996 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: bgmac: fix internal switch initializationhauke
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that requires initialization. We already have code for this, but because of the typo in code it was never working. This resulted in network not working for some routers and possibility of soft-bricking them. Use correct bit for switch initialization and fix typo in the define. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-14brcm47xx: detect Asus RT-N10hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37989 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-14brcm47xx: tg3: use the phy address from et0phyaddr and not the default phy ↵hauke
address. Thank you Devastator for testing. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37986 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-13brcm47xx: board detection, GPIO for Linksys E1000 V2.1hauke
This patch adds board detection for the Linksys E1000 V2.1 router, as well as GPIO support for same. This fixes bug #14135. Currently, wired networking isn't working on the router, and I haven't tried the wireless, but with this patch, OpenWRT successfully boots, and all the LEDs and buttons work properly. Signed-off-by: Zachary Catlin <zcatlin@indiana.edu> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37977 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-13brcm47xx: detect WRT310NV1hauke
Thanks Devastator for testing git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37969 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-12brcm47xx: remove support for kernel 3.8hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37959 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-12brcm47xx: add default config for new kernel config optionhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37958 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-12kernel: update bcma and ssb to wireless-testing master-2013-09-09hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37957 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-07brcm47xx: add me as maintainerhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37916 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-02kernel: update 3.10 to 3.10.10juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37890 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-23kernel: update 3.10 to 3.10.9juhosg
Also refresh 3.10 patches. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37832 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-17brcm47xx: fix typo in Broadcom-bgmac-b43 profile namehauke
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37803 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-04brcm47xx: change board detection for some Asus deviceshauke
This closes #13316 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37680 3c298f89-4303-0410-b956-a3cf2f4a3e73