summaryrefslogtreecommitdiff
path: root/target/linux/brcm47xx
AgeCommit message (Collapse)Author
2013-08-04brcm47xx: change board detection for some Asus deviceshauke
This closes #13316 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37680 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: switch to kernel 3.10.4hauke
This uses a new switch driver. The old ADMTEK Adm6996 switch is not supported any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37650 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: use lib phy when tg3 is in usehauke
This is untested, but probably needed to make it work with the phy lib switch driver. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37649 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: improve detection of Linksys WRTSL54GShauke
This closes #13319 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37647 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: remove support for kernel 3.9hauke
This is not needed any more. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37646 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: add function to get a gpio pin by namehauke
bcm47xx_nvram_gpio_pin() returns a gpio pin number for a given name based on configuration data in nvram. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37644 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-31brcm47xx: run mtd fixtrx linux every timehauke
With this patch it is possible to boot a device with kernel 3.10 a second time. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37625 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-22kernel: update 3.10 to 3.10.2juhosg
Also refresh 3.10 patches. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37502 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-19kernel: move CONFIG_NET_IP_TUNNEL to genericjogo
Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37465 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-19kernel: update bcma and ssb to version from wireless-testing/master tag ↵hauke
master-2013-07-18 This should fix some build problems in b43 with kernel 3.3. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37432 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-15brcm47xx: fix name of patchhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37340 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: use b53 phy driver for the switch in kernel 3.10hauke
This makes it possible to use swconfig to controll the switch. This was tested with devices using b43 and bgmac. This was not tested on devices using tg3. This does not support the adm switch used in some very old devices. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37304 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: add initial support for kernel 3.10hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37287 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: fix switch handlinghauke
This fixes some problems with the switch handling * It now send the messages again to indicate a button for failsafe mode should be pressed * it does not leak packages between wan and lan any more * the switch works again in normal mode The Ethernet connection has to be up when the switch driver switch-robo is insmoded therefor we just do it again. Explicitly set enable_vlan to prevent leaking packages. This should close #13869, #13868 and #13716 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37286 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: do not load the kernel modules needed for Ethernet manuallyhauke
add the boot flag to make the kernel modules needed for Ethernet and diag load on startup. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37284 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: do not change nvram without user interactionhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37281 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-13brcm47xx: proc gets mounted without this patchhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37272 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-13brcm47xx: remove obsolete hotplug stuffhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37271 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-04brcm47xx: fix module insert orderblogic
https://dev.openwrt.org/ticket/13811 Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37161 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-27targets: prepare for supporting normal and initramfs imagesflorian
In order to support both normal images and initramfs, ensure that each target sets KERNELNAME properly so that the generic kernel building code can copy the corresponding files over $(KDIR) with the appropriate extension. Update the various paths to the kernel and wrapper images from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo). Signed-off-by: Florian Fainelli <florian@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37049 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-21brcm47xx: dont manually insmod switch driversblogic
Signed-off-by: John Crispin <bloic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-12brcm47xx: run make kernel_oldconfig for 3.9 kernel confighauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36928 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-12brcm47xx: remove support for kernel 3.6hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36927 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-12brcm47xx: add initial support for kernel 3.9hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36926 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-26kernel: update linux 3.8 to 3.8.13juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36724 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-12kernel: move CONFIG_MIPS_SEAD3 to genericjogo
Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36617 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-08kernel: update linux 3.8 to 3.8.12juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36576 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-01kernel: update linux 3.8 to 3.8.11juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36507 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-28broadcom-diag: support for the WNDR3700v3hauke
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the bootloader and stock firmware will accept. The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving its LEDs through an HC164 8-bit shift register. Signed-off-by: Owen Kirby <osk@exegin.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36482 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-28brcm47xx: use kernel 3.8.10 as default kernelhauke
The biggest change with this kernel is a new partition parser. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36480 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-28brcm47xx: add board detection for NETGEAR WNDR4500 V2hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36478 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-28kernel: update bcma and ssb for kernel 3.8+ to version from wireless-testing ↵hauke
master-2013-04-26. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36473 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-26kernel: update linux 3.8 to 3.8.9juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36453 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-19kernel: backport SSB/BCMA changes in preparation for a compat-wireless updatenbd
Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36367 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06brcm47xx: use old partition names again for kernel 3.8hauke
This fixes sysupgrade. The partition names are used all over the Internet in various howtos. Thank you russell for spotting this problem. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36235 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06brcm47xx: fix error in board detection when nvram is not available.hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36234 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06kernel: update linux 3.8 to 3.8.6juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36215 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-27brcm47xx: generate images for Linksys E.... modelshauke
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36139 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-27brcm47xx: activate image generation for some Netgear devices which are on ↵hauke
the market and should be supported. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36137 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-27brcm47xx: generate images for more WRT...N modelshauke
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36136 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-20brcm47xx: generate images for some more deviceshauke
These devices should be supported by trunk now. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36099 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-15kernel: update linux 3.8 to 3.8.3juhosg
Also refresh the related generic/platform patches. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36039 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-10brcm47xx: refresh confighauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35948 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-09brcm47xx: add some more partition parser fixes by Rafał Miłeckihauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35912 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-09brcm47xx: netconfig: add bacis support for swconfighauke
Parse the cpu port from swconfig and explicitly mark the cpu port as tagged. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35911 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-28brcm47xx: bgmac: omit the fcshauke
This fixes #13058 and hopefully #12927 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35834 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-28brcm47xx: bgmac: update to version form netdev git repositoryhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35833 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-25brcm47xx: use bcm47xx_board_get() and detect some more boards in flash ↵hauke
partition driver git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35791 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-25brcm47xx: board detection WNDR3400v2hauke
WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#". CFE and NVRAM contain different vars - example: CFE line original: Device eth0: hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0 CFE after openwrt: Device eth0: hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0 Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2 (and on wikidevi for example) Signed off by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35790 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-24brcm47xx: use same board detection code as kernel 3.8hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35770 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-21 08:38:26 +0000