summaryrefslogtreecommitdiff
path: root/target/linux/brcm47xx
AgeCommit message (Collapse)Author
2013-02-28brcm47xx: bgmac: omit the fcshauke
This fixes #13058 and hopefully #12927 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35834 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-28brcm47xx: bgmac: update to version form netdev git repositoryhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35833 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-25brcm47xx: use bcm47xx_board_get() and detect some more boards in flash ↵hauke
partition driver git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35791 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-25brcm47xx: board detection WNDR3400v2hauke
WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#". CFE and NVRAM contain different vars - example: CFE line original: Device eth0: hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0 CFE after openwrt: Device eth0: hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0 Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2 (and on wikidevi for example) Signed off by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35790 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-24brcm47xx: use same board detection code as kernel 3.8hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35770 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-20brcm47xx: do not use vlan0 any more.hauke
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325. This makes OpenWrt always use vlan1 and vlan2 instead. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35704 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16brcm47xx: add initial support for kernel 3.8hauke
This contains the following new bigger changes: * new partition parser which still could lake some features or have bugs * new nand flash driver * using physmap-flash flash driver for parallel flash * some changes to the serial flash driver With these changes OpenWrt starts using more of the mainline flash drivers. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35632 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16brcm47xx: BGMAC - Adjust AutoLoad number to be prior to switch moduleshauke
Adjust the "AutoLoad" number for the BGMAC module to be prior to the switch modules. This probably isn't real important as the modules are loaded in the correct order by preinit anyway. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35625 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16brcm47xx: improve cpuport detection for filesafehauke
Do not try to load bcm57xx.ko any more this is not needed for kernel 2.6 and 3.X Ask the switch driver where the CPU port is. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35624 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16brcm47xx: fix network config on simpleshare hauke
The included patch will generate a correct network configuration on the simpletech simpleshare. Thank you for the patch Will Holmes (RealOpty) This closes #12361. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35623 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16brcm47xx: handle return values of cfe_env_get() correctly.hauke
This closes #12746. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35622 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16brcm47xx: bgmac: fix unaligned accesses to network headers.hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35621 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16brcm47xx: fix unaligned access to mac addresshauke
The mac address should be aligned to u16 to prevent an unaligned access in drivers/ssb/pci.c where it is casted to __be16. This closes #9824. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35618 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16brcm47xx: try to automatically detect if the wan port is at port 4 and not ↵hauke
at port 0. This should fix #13000. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35617 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-14brcm47xx: if the cpuport of the switch is port 8 assume vlan0ports: "1 2 3 4 ↵hauke
8" and vlan0ports: "0 8" git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35597 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-13brcm47xx: configure vlan correctly on some recent devices.hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35587 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-12brcm47xx: add some more fixes to bgmachauke
Thank you Rafał Miłecki and Nathan Hintz git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35574 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-12brcm47xx: update tg3 to the version send upstreamhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35573 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-06brcm47xx: fix name of kmod-ocf-ubsec-ssbhauke
This also removes kmod-ocf, because kmod-crypto-ocf is automatically selected by kmod-ocf-ubsec-ssb. Thank you Manuel Munz <freifunk@somakoma.de> for the patch. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35509 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-06brcm47xx: bgmac: make it possible to set the devices into promisc mode when ↵hauke
it is already up This fixes #12927. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35507 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-04brcm47xx: fix detection of Asus RT-N16hauke
This fixes #12936. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35492 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-04Add Failsafe support for Linksys E3000V1 / WRT610NV2hauke
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2 in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to be expanded. Is there a way to determine the correct cpu_port to use in a generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if "/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could a similar method be used in "/etc/init.d/netconfig"? Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35491 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-04brcm47xx: Fix switch config on 4716/53115 deviceshauke
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35490 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-27brcm47xx: load pps_core and ptp before tg3 to make the interface available ↵hauke
for failsafe. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35341 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-26brcm47xx: create image for Netgear WNDR3400 V1hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35323 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-26brcm47xx: add initial board detection codehauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35322 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-26brcm47xx: add gpio to irq function againhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35321 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-24brcm47xx: change generic profileshauke
The default profile now contains Ethernet drivers for all the types found on supported boards. There are other profiles for each Ethernet driver. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35314 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-12brcm47xx: BCMA - Update default IRQ assignment per upstream changehauke
Update the default IRQ assignment for unrecognized devices per the upstream change. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35121 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-10brcm47xx: update bgmac driver to the version in mainline kernelhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35083 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-10kernel: update bcma and ssb to master-2013-01-09 from wireless-testinghauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35080 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-07brcm47xx: BGMAC Driver correctionshauke
1) Fix what appears to be a logic error in bgmac_phy_advertise. 2) Fix bgmac_ioctl to use passed phy_id; needed for switch-robo interface w/ the driver to work correctly. I still have the issue with the interface always being HD when the speed/duplex is set manually (e.g., echo "100FD" > /proc/switch/eth0/port/N/media). Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35052 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: various fixes and code cleanups for irq codehauke
This is based on a patch send by Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34997 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: add bgmac driverhauke
This Ethernet driver is in early development stage and still has some problems. This was working on my bcm4716 based device. Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34995 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: build b44 as a modulehauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34994 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: run ifup before starting the switchhauke
In addition check_module is not needed, nobody checks the return value. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: BCMA - IRQ Update - Fix IRQ Flag for I2S Corehauke
Adjust the IRQ Flag value from 8 to 7 for I2S Core for BCM4716 and BCM4748 (per the Broadcom SDK). IRQ Flag values greater than 7 are ignored when setting the interrupt masks. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34990 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: improve IRQ handling for bcma based deviceshauke
This was party inspirited by patches send by Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34989 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: add a new version of the nvram rewrite patchhauke
This is the version like it was send for mainline inclusion. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34988 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: move patches already in the mainline kernel to the fronthauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34987 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-03brcm47xx: remove support for kernel version 3.3hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34986 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-27brcm47xx: bcma: correct M25P32 serial flash IDhauke
Thank you Rafał Miłecki. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34900 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-19Do not use deprecated path to functions.sh (/etc/functions.sh -> ↵mirko
/lib/functions.sh) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34793 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-19Do not overload mount-call - trying to reduce confusionmirko
The behaviour of calling 'mount' differed depending on whether it called the busybox-mount, the mount of util-linux, the mount defined in /lib/functions.sh and /lib/functions/boot.sh /etc/preinit even included /lib/functions.sh and /lib/functions/boot.sh, both re-defining 'mount'. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34792 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-18kernel: update linux 3.6 to 3.6.11juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34748 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-14brcm47xx: improve suppressing printing if a module was found in preinit ↵hauke
function. Thank you Bastian Bittorf git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34680 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-13brcm47xx: Additional BCM4716 supporthauke
Additional BCM4716 support. Still needs working ethernet driver. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34672 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-13brcm47xx: BCMA - Broadcom 2011 SDK Updateshauke
I noticed these changes when reviewing the 2011 Broadcom SDK. I haven't noticed any obvious changes in behavior with them applied; but thought I should at least pass them on. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34670 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-13brcm47xx: return the real irq number in bcma_core_irqhauke
The irq signal numbers that are send by the cpu are increased by 2 from the number programmed into the mips core by bcma. Return the irq number on which the irqs are send in bcma_core_irq() now. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34669 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-13brcm47xx: this usb patch is not needed, the Broadcom SDK does it the other way.hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34655 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.46.0) at 2024-12-29 18:56:52 +0000