summaryrefslogtreecommitdiff
path: root/target/linux/brcm47xx
AgeCommit message (Collapse)Author
2013-09-16brcm47xx: Add support for Huawei E970hauke
This patch adds support for Huawei E970 wireless gateway devices. It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV. E960/B970 should work too, from what I know it's basically the same hardware. The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem. It uses a hardware watchdog which needs GPIO-7 to be toggled at least every 1-2 seconds. This patch uses gpio_wdt module (see my previous patch today) to take care of this. Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset button, image to be used for upgrade from OEM firmware's web interface Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970> Issue: * lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog reset during kernel decompress. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: add detection for Phicomm M1hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38009 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: detect Linksys E1200 V2hauke
This adds detection for Linksys E1200 V2 Thank you Lightsword and Rafał. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38006 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: mtd: bcm47xxpart: detect "factory" partitionhauke
A new type of partition with magic FCTY was found on Huawei E970: 46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290| Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38005 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: bgmac: implement unaligned addressing for DMA rings that support ithauke
This is important patch for new devices that support unaligned addressing. That devices suffer from the backward-compatibility bug in DMA engine. In theory we should be able to use old mechanism, but in practice DMA address seems to be randomly copied into status register when hardware reaches end of a ring. This breaks reading slot number from status register and we can't use DMA anymore. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38004 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: add detection code for Huawei E970hauke
This is based on a patch by Mathias Adam. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38001 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15kernel: update 3.10 to 3.10.12juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38000 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: bgmac: allow bigger et_swtype nvram variablehauke
Without this patch it is impossible to read et_swtype, because the 1 byte space is needed for the terminating null byte. Now it should be possible to read decimal and hex vars of max 8 bit. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37999 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: mtd: bcm47xxpart: detect block aligned Squashfs partitionhauke
Most of the bcm47xx devices use TRX format for storing kernel and some partition like Squashfs or JFFS2. This is pretty flexible solution, CFE (the bootloader) just writes (and later boots) TRX at some hardcoded place and paritions can vary in the size. However some devices don't use TRX format. Very recently we have discovered ZTE H218N that has kernel and rootfs partitions at some "random" places. This patch allows Linux find a rootfs partition after installing custom image with a CFE bootloader. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37998 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: update board detection patchhauke
* Use different structs depending on the number of nvram variables to check. * Add detection of ZTE H218N, this closes #14151. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37996 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-15brcm47xx: bgmac: fix internal switch initializationhauke
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that requires initialization. We already have code for this, but because of the typo in code it was never working. This resulted in network not working for some routers and possibility of soft-bricking them. Use correct bit for switch initialization and fix typo in the define. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-14brcm47xx: detect Asus RT-N10hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37989 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-14brcm47xx: tg3: use the phy address from et0phyaddr and not the default phy ↵hauke
address. Thank you Devastator for testing. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37986 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-13brcm47xx: board detection, GPIO for Linksys E1000 V2.1hauke
This patch adds board detection for the Linksys E1000 V2.1 router, as well as GPIO support for same. This fixes bug #14135. Currently, wired networking isn't working on the router, and I haven't tried the wireless, but with this patch, OpenWRT successfully boots, and all the LEDs and buttons work properly. Signed-off-by: Zachary Catlin <zcatlin@indiana.edu> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37977 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-13brcm47xx: detect WRT310NV1hauke
Thanks Devastator for testing git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37969 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-12brcm47xx: remove support for kernel 3.8hauke
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37959 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-12brcm47xx: add default config for new kernel config optionhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37958 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-12kernel: update bcma and ssb to wireless-testing master-2013-09-09hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37957 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-07brcm47xx: add me as maintainerhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37916 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-02kernel: update 3.10 to 3.10.10juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37890 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-23kernel: update 3.10 to 3.10.9juhosg
Also refresh 3.10 patches. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37832 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-17brcm47xx: fix typo in Broadcom-bgmac-b43 profile namehauke
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37803 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-04brcm47xx: change board detection for some Asus deviceshauke
This closes #13316 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37680 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: switch to kernel 3.10.4hauke
This uses a new switch driver. The old ADMTEK Adm6996 switch is not supported any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37650 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: use lib phy when tg3 is in usehauke
This is untested, but probably needed to make it work with the phy lib switch driver. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37649 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: improve detection of Linksys WRTSL54GShauke
This closes #13319 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37647 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: remove support for kernel 3.9hauke
This is not needed any more. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37646 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-08-01brcm47xx: add function to get a gpio pin by namehauke
bcm47xx_nvram_gpio_pin() returns a gpio pin number for a given name based on configuration data in nvram. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37644 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-31brcm47xx: run mtd fixtrx linux every timehauke
With this patch it is possible to boot a device with kernel 3.10 a second time. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37625 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-22kernel: update 3.10 to 3.10.2juhosg
Also refresh 3.10 patches. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37502 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-19kernel: move CONFIG_NET_IP_TUNNEL to genericjogo
Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37465 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-19kernel: update bcma and ssb to version from wireless-testing/master tag ↵hauke
master-2013-07-18 This should fix some build problems in b43 with kernel 3.3. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37432 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-15brcm47xx: fix name of patchhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37340 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: use b53 phy driver for the switch in kernel 3.10hauke
This makes it possible to use swconfig to controll the switch. This was tested with devices using b43 and bgmac. This was not tested on devices using tg3. This does not support the adm switch used in some very old devices. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37304 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: add initial support for kernel 3.10hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37287 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: fix switch handlinghauke
This fixes some problems with the switch handling * It now send the messages again to indicate a button for failsafe mode should be pressed * it does not leak packages between wan and lan any more * the switch works again in normal mode The Ethernet connection has to be up when the switch driver switch-robo is insmoded therefor we just do it again. Explicitly set enable_vlan to prevent leaking packages. This should close #13869, #13868 and #13716 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37286 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: do not load the kernel modules needed for Ethernet manuallyhauke
add the boot flag to make the kernel modules needed for Ethernet and diag load on startup. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37284 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: do not change nvram without user interactionhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37281 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-13brcm47xx: proc gets mounted without this patchhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37272 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-13brcm47xx: remove obsolete hotplug stuffhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37271 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-04brcm47xx: fix module insert orderblogic
https://dev.openwrt.org/ticket/13811 Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37161 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-27targets: prepare for supporting normal and initramfs imagesflorian
In order to support both normal images and initramfs, ensure that each target sets KERNELNAME properly so that the generic kernel building code can copy the corresponding files over $(KDIR) with the appropriate extension. Update the various paths to the kernel and wrapper images from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo). Signed-off-by: Florian Fainelli <florian@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37049 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-21brcm47xx: dont manually insmod switch driversblogic
Signed-off-by: John Crispin <bloic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-12brcm47xx: run make kernel_oldconfig for 3.9 kernel confighauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36928 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-12brcm47xx: remove support for kernel 3.6hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36927 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-12brcm47xx: add initial support for kernel 3.9hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36926 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-26kernel: update linux 3.8 to 3.8.13juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36724 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-12kernel: move CONFIG_MIPS_SEAD3 to genericjogo
Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36617 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-08kernel: update linux 3.8 to 3.8.12juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36576 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-05-01kernel: update linux 3.8 to 3.8.11juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36507 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-08 16:02:08 +0000