summaryrefslogtreecommitdiff
path: root/target/linux/brcm47xx/image
AgeCommit message (Collapse)Author
2013-09-16brcm47xx: Add support for Huawei E970hauke
This patch adds support for Huawei E970 wireless gateway devices. It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV. E960/B970 should work too, from what I know it's basically the same hardware. The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem. It uses a hardware watchdog which needs GPIO-7 to be toggled at least every 1-2 seconds. This patch uses gpio_wdt module (see my previous patch today) to take care of this. Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset button, image to be used for upgrade from OEM firmware's web interface Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970> Issue: * lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog reset during kernel decompress. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-06-27targets: prepare for supporting normal and initramfs imagesflorian
In order to support both normal images and initramfs, ensure that each target sets KERNELNAME properly so that the generic kernel building code can copy the corresponding files over $(KDIR) with the appropriate extension. Update the various paths to the kernel and wrapper images from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo). Signed-off-by: Florian Fainelli <florian@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37049 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-28broadcom-diag: support for the WNDR3700v3hauke
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the bootloader and stock firmware will accept. The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving its LEDs through an HC164 8-bit shift register. Signed-off-by: Owen Kirby <osk@exegin.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36482 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-27brcm47xx: generate images for Linksys E.... modelshauke
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36139 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-27brcm47xx: activate image generation for some Netgear devices which are on ↵hauke
the market and should be supported. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36137 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-27brcm47xx: generate images for more WRT...N modelshauke
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36136 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-20brcm47xx: generate images for some more deviceshauke
These devices should be supported by trunk now. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36099 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-25brcm47xx: board detection WNDR3400v2hauke
WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#". CFE and NVRAM contain different vars - example: CFE line original: Device eth0: hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0 CFE after openwrt: Device eth0: hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0 Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2 (and on wikidevi for example) Signed off by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35790 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-01-26brcm47xx: create image for Netgear WNDR3400 V1hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35323 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-13brcm47xx: Additional BCM4716 supporthauke
Additional BCM4716 support. Still needs working ethernet driver. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34672 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-10-27[brcm47xx]: generate images for the D-Link DWL-3150 as wellkaloz
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33961 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-08-05[brcm47xx] generate image for Linksys e3200hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33003 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-13brcm47xx: generate image for Linksys WRT610N V1hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31696 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-18brcm47xx: add code to generate images for some netgear deviceshauke
This is commented out until we get report of working devices. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30639 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-29brcm47xx: fix padding of trx images, padjffs2 does not work properly on ↵nbd
empty files by default git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28125 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29brcm47xx: deactivate wndr3400 for now as this device will not boothauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27316 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-28brcm47xx: generate image to flash on Netgear WNDR3400.hauke
The image will not boot because serial flash support is missing this is only for experts. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27302 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-15bcm47xx: Remove kernel checks from image Makefilehauke
2.4 isn't present anymore, so it will always be 2.6 (or newer). Since the 2.6 check will break with 3.0, remove it alltogether. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27185 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-02brcm47xx: Add edimax PS1208mfg supporthauke
Thank you clemvangelis for the patches. (closes #7672) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24217 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-06brcm47xx: do not generate image for wgr614_v8 as long as we did not get any ↵hauke
positive reports with that device. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22522 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-06brcm47xx: Add new image generation and fix leds/reset button on WNR834B V2hauke
Thank you realopty for the patch. tools/firmware-utils/src/mkchkimg.c is from http://www.myopenrouter.com/download/10611/mkchkimg/ This closes #7702. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22516 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-30mostly revert commit r22396hauke
CFE does not boot images generated with these checksums because of wrong checksum. After flashing then with tftp to my Asus wl500-GPv1 the following messages are show: Null Rescue Flag. Boot program checksum is invalid Hello!! Enter Rescue Mode: (Check error) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22418 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-27fix CRC32 calculation for sysupgrademarkus
* reduce image size for CRC calculation by fs_mark size sysupgrade sometimes failed for me and I noticed that it was due to incorrect CRC values in trx-header after performing it. It seems that the fs_mark was completely included in the calculation and that it was nevertheless modified by sysupgrade while appending the jffs data. This only occurs for the first boot after sysupgrade as the flashmap driver recalculates the CRC to an even smaller area when it boots. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22396 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-01renamed wrt54g3gv2-vf imagesmarkus
'factory' and 'sysupgrade' did not make much sense. A discussion with jow convinced me that .trx results in a helpdesk disaster. So I decided to use '.bin' for normal bin-headers and '.noheader.bin' for the trx-v2 image. I fixed the wiki accordingly. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22013 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-06-26add back the base-files/image code from brcm-2.4 to brcm47xxnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21945 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-06-26remove brcm47xx symlinks to brcm-2.4 (unfortunately svn does not allow a ↵nbd
proper type changing commit) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21944 3c298f89-4303-0410-b956-a3cf2f4a3e73
2007-09-06strip the kernel version suffix from target directories, except for brcm-2.4 ↵nbd
(the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@8653 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-01 23:32:31 +0000