summaryrefslogtreecommitdiff
path: root/target/linux/brcm47xx/config-3.10
AgeCommit message (Collapse)Author
2013-12-01brcm47xx: config: set CONFIG_HZ=100 and CONFIG_IP_ROUTE_VERBOSEhauke
This sets both values to the OpenWrt default values. There is no reason to use some brcm47xx specific values here. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38978 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-01brcm47xx: add vectored interruptshauke
This adds support for vectored interrupts in this SoC. This is supported by the 74K cpus. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38975 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-09brcm47xx: register ADM6996L switchhauke
This patch makes it possible to use adm6996.c on first generation BCM47XX devices with ADM switches. This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for the device. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38699 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-13brcm47xx: activate ARP daemon supporthauke
This just add some bytes to the kernel and is activated on other targets. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38388 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-06brcm47xx: update early printk patcheshauke
Early printk was disabled because it caused hangs on some devices, the old patches were using the CFE console now we use the normal serial console, it is at a constant address. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38309 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-25kernel: b53: add Register Access Bridge Registers (SRAB) interfacehauke
The SRAB interface is used on BCM4707 and BCM5301X SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38198 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16brcm47xx: Add support for Huawei E970hauke
This patch adds support for Huawei E970 wireless gateway devices. It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV. E960/B970 should work too, from what I know it's basically the same hardware. The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem. It uses a hardware watchdog which needs GPIO-7 to be toggled at least every 1-2 seconds. This patch uses gpio_wdt module (see my previous patch today) to take care of this. Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset button, image to be used for upgrade from OEM firmware's web interface Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970> Issue: * lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog reset during kernel decompress. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-12brcm47xx: add default config for new kernel config optionhauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37958 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-19kernel: move CONFIG_NET_IP_TUNNEL to genericjogo
Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37465 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: use b53 phy driver for the switch in kernel 3.10hauke
This makes it possible to use swconfig to controll the switch. This was tested with devices using b43 and bgmac. This was not tested on devices using tg3. This does not support the adm switch used in some very old devices. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37304 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14brcm47xx: add initial support for kernel 3.10hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37287 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-01 23:28:49 +0000