summaryrefslogtreecommitdiff
path: root/target/linux/ar71xx
AgeCommit message (Collapse)Author
2014-01-25ar71xx: archer c7: define LEDs connected to the AR8327 switchjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39395 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-25ar71xx: image: move WNDAP360 macrojuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39394 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-24ar71xx: fix bad RX sensitivity on newer TL-WDR4300 boardsjuhosg
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz interface are connected to GPIO lines. Because these GPIO lines are disabled by default, the RX sensitivity of the device is quite bad. Setup the GPIOs of the external LNAs to fix the issue. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39392 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-24ar71xx: image: generate sysupgrade images for the Compex boardsjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39391 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-24ar71xx: add sysupgrade support for the Compex boardsjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39390 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-24ar71xx: image: use a single firmware partition on Compex devicesjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39389 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-24ar71xx: enable MTD_SPLIT_LZMA_FW optionjuhosg
It will be used for Compex devices. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39388 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-24ar71xx: image: detect partition sizes in the Image/Build/Ath macrojuhosg
Get the size of the mtd partitions directly from the MTD layout and remove the superfluous macro parameters. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39384 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-24ar71xx: image: fix size verification in the CatFiles macrojuhosg
The macro checks the size of the rootfs image even if the second parameter of the macro contains the size of an eraseblock. It is wrong because the size of the kernel image will be adjusted to the next eraseblock and the resulting image might be too large. Fix the macro to check the size of the final image instead of the rootfs image. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39383 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-23ar71xx: ap83: define mtd layout via command linejuhosg
Also use the RKuImage macro becasue the original firmware starts with the rootfs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39379 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-23ar71xx: ap81: define mtd layout via command linejuhosg
Also use the RKuImage macro becasue the original firmware starts with the rootfs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39378 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-23ar71xx: image: show size limit in warning messagesjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39376 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-23ar71xx: add initramfs image support for Compex devicesjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39375 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-23ar71xx: wp543: use KEY_RESET code for the sw4 buttonjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39374 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-23ar71xx: create wndr3700 network config from uci-defaultsluka
Since that was the last configuration in defconfig directory we can drop the defconfig init script too. Signed-off-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39373 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-21ar71xx: mynet-n750: define LEDs connected to the AR8327 switchjuhosg
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4743/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39361 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-20ar71xx: tl-wr1043nd-v2: define LEDs connected to the AR8327 switchjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39346 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-20ar71xx: tl-wdr4300: define LEDs connected to the AR8327 switchjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39345 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-20ar71xx: set default LED config for the RB2011* boardsjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39344 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-20ar71xx: set status_led for the RB2011* boardsjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39343 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-20ar71xx: fix indentation in diag.shjuhosg
Replace the leading spaces with tabs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39342 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-20ar71xx: rb2011: define LEDs connected to the AR8327 switchjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39341 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-20ar71xx: enable AR8327 LED supportjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39340 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-20ar71xx: rb2011: fix eth5 LEDjuhosg
The eth5 LED on the RB2011 is not working because the LED control rule is missing. Fix it. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39335 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-18[ar71xx]: generate images for the On Networks N150 (rebranded Netgear WNR612v2)kaloz
Signed-off-by: Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39320 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-11kernel: update 3.10 to 3.10.26juhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39220 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-11ar71xx: ag71xx: increase calculated max frame length valuejuhosg
The r39147 commit introduces a regression: at lease on some routers with ar8216 switch large packets get lost if 802.1q tagged port is used on the interface connected to the aforementioned switch. The r39147 changes code in the way so interface is set to accept packets no longer than max ethernet frame length for a given mtu. Unfortunately ar8216 has a feature: it sends two additional bytes as a packet header and those this header needs to be added to the max frame length. Otherwise long enough packets get lost. The problem only manuifests itself if interface is used in vlan tagged mode. If interface is untagged then ar8216's header fits into space used by 802.1q tag and not packets are lost. Include two additional bytes in the max frame length calculation to fix the issue. This patch is tested and works with Trendnet TEW-632BRP. Signed-off-by Nikolay Martynov <mar.kolya@gmail.com> Patchwork: http://patchwork.openwrt.org/patch/4656/ [juhosg: - simplify the patch to include the additional bytes of the switch header unconditionally, - change subject and update commit message] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39219 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-10ar71xx: my net n750: simplify LNA GPIO setupjuhosg
Use the ath79_wmac_set_ext_lna_gpio helper instead of exporting the GPIOs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39217 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-10ar71xx: my net n600: simplify LNA GPIO setupjuhosg
Use the ath79_wmac_set_ext_lna_gpio helper instead of exporting the GPIOs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39216 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-10ar71xx: add a helper function for external LNA GPIO setupjuhosg
The built-in wireless MAC of the AR934x SoC can handle external LNAs and the control signal of the LNAs can be routed to any GPIO line. Add a helper function which can be used to configure the GPIO lines. The helper function will be used for AR934x boards which are using externel LNAs to improve sensitivity. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39215 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-10ar71xx: Fix WD My Net N600 weak signal issuejuhosg
The LNAs need to be enabled by setting their respective GPIO to high even though the original firmware's setting sets them to low on initialization. Obviously the LNAs are then later initialized by the driver on the OEM firmware. Without this fix the device is mostly "deaf". Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Tested-by: Steven Haigh <netwiz@crc.id.au> Patchwork: http://patchwork.openwrt.org/patch/4689/ [juhosg: - remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all, - change subject and update the commit message] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39214 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-10ar71xx: Fix WD My Net N750 weak signal issuejuhosg
The LNAs need to be enabled by setting their respective GPIO to high even though the original firmware's setting sets them to low on initialization. Obviously the LNAs are then later initialized by the driver on the OEM firmware. Without this fix the device is mostly "deaf". Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4688/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39213 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-23ar71xx: fix max frame length of the QCA955x SoCsjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39161 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-23ar71xx: don't set builtin_switch flag for QCA9558juhosg
It makes no sense, the SoC has no built-in switch. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39160 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-20ar71xx: allow to use large ethernet frames on AR934x SoCsjuhosg
The hardware supports large ethernet frames. Override the maximum frame length and packet lenght mask in the platform data to allow to use large MTU on the ethernet interfaces. Limit the feature to AR934x SoCs for now. It should work on some other SoCs as well, but those has not been tested yet. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39149 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-20ar71xx: ag71xx: fix max frame length setup of the built-in switchesjuhosg
The currently used bitmask of the maximum frame length field is wrong for both models. On AR724x/AR933x the largest frame size is 2047 bytes, on the AR934x it is 16383 bytes. Make the MTU setup code model specific, and use the correct bitmask for both models. Also change the value to the maximum. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39148 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-20ar71xx: ag71xx: calculate max frame len register value from the MTUjuhosg
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init() and write the correct value into that from the ag71xx_open() and ag71xx_fast_reset() functions. Also recalculate the RX buffer size based on the actual maximum frame length value to optimize memory allocation. Additionaly, disallow to change the MTU value while the interface it running. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39147 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-20ar71xx: ag71xx: add ag71xx_max_frame_len() helperjuhosg
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39146 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-20ar71xx: ag71xx: get max_frame_len and desc_pktlen_mask from platform datajuhosg
This will allow to use SoC specific values for both. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39145 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-20ar71xx: ag71xx: store descriptor packet length mask in ag71xx structjuhosg
The currently used bitmask is not correct for all SoCs. Introduce a new field in struct ag71xx and store the bitmask in that. Use the current value for now, it will be adjusted for each SoCs in further patches. Aslo use the new field directly in the ag71xx_rx_packets and ag71xx_hard_start_xmit() functions and remove the ag71xx_desc_pktlen() helper. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39144 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-19ar71xx: add missing tx gain table flag for buffalo wzr-hp-g450hnbd
Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39139 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: enable images for WD My Net N750juhosg
Now that the switch works correctly we can enable the images for this board. Flashing from the factory firmware, the factory failsafe loader and sysupgrade was tested successfully. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4617/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39130 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: fix WD My Net N750 switch led cfgjuhosg
Now that the switch is working correctly I had the chance to actually test the LED config. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4616/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39129 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: implement switch fix for WD My Net N750juhosg
The bootloader on the WD My Net N750 disables the ports on it's internal AR8327N switch by powering them down. The stock firmware then brings the ports back up again by starting the auto negotiation process on each port. This fix implements just that. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4615/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39128 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: implement callback in mdio resetjuhosg
This enables us to add fixups to the board specific code for boards that require special treatment of PHYs on mdio bus reset. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> http://patchwork.openwrt.org/patch/4614/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39127 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: make ag71xx_mdio_platform_data visiblejuhosg
This enables us to modify the ag71xx_mdio_platform_data from within the board support files. Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4613/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39126 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: ag71xx: compute the RX buffer size from the maximum frame sizejuhosg
Currently, the AG71XX_RX_PKT_SIZE value limits the received frame size to 1514/1516 bytes with/without a VLAN header respectively. However the hardware limit is controlled by the value the AG71XX_REG_MAC_MFL register which contains the value of the max_frame_len field. Compute the RX buffer size from the max_frame_len field to get rid of the 1514/1516 byte limitation. Also remove the unused AG71XX_RX_PKT_SIZE definition. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39121 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: ag71xx: store RX buffer size in the ag71xx structjuhosg
This allows to change the value dynamically. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39120 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: ag71xx: store maximum frame length in the ag71xx structjuhosg
This will allow to use different values for the different SoCs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39117 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-17ar71xx: ag71xx: use mdio bus name in ar7240_probe messagesjuhosg
The ar7240_probe function uses the network device name in the kernel log messages, however the name is not yet initialized when the ar7240_probe function is called. Use the mdio bus name in the messages to avoid ugly log lines like the following one: eth%d: Found an AR7240/AR9330 built-in switch Reported-by: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39116 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.46.0) at 2024-12-24 17:50:29 +0000