summaryrefslogtreecommitdiff
path: root/target/linux/ar71xx/files
AgeCommit message (Collapse)Author
2011-10-24ar71xx: Buffalo WHR-HP-G300N kernel supportjuhosg
The initial support for the Buffalo WHR-HP-G300N box. The code was confirmed to boot and run, but not tested in depth. Known problem: iw phy phy0 info shows: Coverage class: 0 (up to 0m) Available Antennas: TX 0 RX 0 Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28567 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24ar71xx: add kernel support for the Allnet ALL0258N boardjuhosg
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge. The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio, it got 8MB of NOR and 32MB SDRAM. Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28564 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-11linux: ar71xx: add support for Mikrotik Routerboard RB493Gjogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28423 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-08ag71xx: close a race between the phy state machine and link statejogo
A fast stop/start cycle could leave the ag71xx interrupts and tx engine disabled when using a phy driver with a fixed link and the start/stop happens between two phy state machine polls. Prevent this by always forcing the link down on stop regardless of phy state and having a phy connected. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28380 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-23ar71xx: fix MAC addresses on the DIR-825-B1 boardjuhosg
Patch-by: Lukas Kuna git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28295 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-21ar71xx: add support for the TP-Link TL-WR703N v1 boardjuhosg
Based on a patch by dongyuqi <729650915@qq.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28277 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-21ar71xx: add AR933x specific USB setup functionjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28276 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-21ar71xx: add ar71xx_device_reset_rmw helperjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28275 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-21ar71xx: remove 'default [yn]' from machine Kconfig entriesjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28273 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-21ar71xx: sort AR71XX_MACH_* entriesjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28272 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-11ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins)nbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28213 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-06ar71xx: do not count normal interrupts as spurious (fixes #10037)nbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28182 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-29ar71xx: fix ethernet PLL setting on ar7242nbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28124 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-13ar71xx: add some code to detect DMA stuck conditions on ar7240nbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27975 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-13ar71xx: on ar724x only reset the link status in the restart handler, the ↵nbd
fast reset takes care of DMA stuck issues git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27973 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-11ar71xx: adjust the mtd layout of tew-632brp and dir-615c to match the image ↵nbd
layout (fixes #9922) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27959 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-04ar71xx: fix ethernet FIFO state corruption on ar7240nbd
When starting/stopping DMA sometimes the FIFO state gets corrupted, leading to wildly fluctuating latencies or packet data corruption. Fix this by issuing a fast MAC reset as soon as the link is detected as up. Fixes #9689, #9405 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27896 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-04ag71xx: fix memory corruption issues on ar7240 on ethernet start/stopnbd
When the DMA engine state gets corrupted due to a hardware issues, it often won't stop rx until a full reset is issued. In that case the hardware must keep a valid descriptor, otherwise it will write to random places in system RAM, triggering random crashes. To fix this, keep a dummy descriptor without a buffer that keeps the DMA engine in a sane state until the reset is done git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27895 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-04ar71xx: fix MAC/MDIO reset mask handlingnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27894 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-28ar71xx: merge WZR-HP-G301NH support into WZR-HP-G300NHjogo
Now that we can use a generic name for the switch there is no need for a separate image for the WZR-HP-G301NH. Update the default network config and remove the extra image. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27814 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-24ar71xx: autodetect rtl8366s/rtl8366rb on wzr-hp-g300nhnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27756 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-24rtl8366: unify rtl8366s and rtl8366rb platform datanbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27754 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-24ar71xx: enable the usb power regulator on the wzr-hp-ag300h through gpio 2 ↵nbd
(#9684) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27739 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20ar71xx: reinitialize global switch settings after reset on ar7240nbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27705 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20ar71xx: configure address aging on ar7240nbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27704 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20ar71xx: reset the phy in the ethernet init on ar724xnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27703 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20ar71xx: make sure that rx and interrupts are disabled before issuing the ↵nbd
hardware reset git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27702 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20ar71xx: increase the delay after the ethernet MAC resetnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27701 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20ar71xx: fix an unused variable warningnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27700 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-09ar71xx: do not reset the hardware on transmit timeout - this would mess up ↵nbd
the up the PHY state git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27568 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-09ag71xx: keep the rx engine stopped while the link is not up, should ↵nbd
hopefully fix stability issues from #9405 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27567 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-30ar71xx: remove CONFIG_MTD_CONCAT ifdefs from the WZR-HP-AG300H codejuhosg
The config option has been removed in 2.6.39. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27320 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29ar71xx: merge 2.6.39 patchesjuhosg
Also remove the old UART driver for ar933x. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27314 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29ar71xx: add 2.6.39 supportjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27310 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29ar71xx: remove ar71xx_gpio_irq_set_typejuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27309 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29ar71xx: add separate handlers for IP3 interruptsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27308 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29ar71xx: use separate handlers for IP2 interruptsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27307 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29ar71xx: remove useless irq_desc.status initializationsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27306 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-25ar71xx: bring up secondary radio on wzr-hp-ag300h (fixes #9608)nbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27282 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-19ar71xx: cleanup AR933X UART driverjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27222 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-19ar71xx: fix uart clock frequency for AR933Xjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27221 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-13ar71xx: use ar933x_uart.h in the AR933X serial driverjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27166 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-13ar71xx: update early_printk codejuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27165 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-04ar71xx: setup wdt_clock for AR913X to avoid a kernel bugjuhosg
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27102 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-04ar71xx: select the internal antenna by default on the ZCN-1523H boardsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27101 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-01Revert "ar71xx: only enable the rx engine after the link is up..."nbd
It messes up the DMA state when the link goes down git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27088 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-01ar71xx: init external_reset for AR933Xjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27083 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-01ar71xx: add external_reset field to ath9k_platform_datajuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27082 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-01ar71xx: init get_mac_revision on AR9330 rev 1juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27081 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-01ar71xx: add get_mac_revision to ath9k_platform_datajuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27080 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-02 12:32:25 +0000