Age | Commit message (Collapse) | Author |
|
The WLAN LEDs are not working yet.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29680 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
It is based on patches from the linux-longsoon-community git tree:
http://dev.lemote.com/cgit/linux-loongson-community.git/
Now the kernel can use the command line parameter from kexec-tools.
Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped
before executing the new kernel). Compile tested with lantiq (3.1.4)
and brcm47xx (3.0.12).
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29674 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29669 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29662 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29651 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29635 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29630 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29567 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29535 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29441 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29415 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28801 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
The ethernet port LEDs are not working yet.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28706 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Based on a patch by Marek Lindner <marek@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28617 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.
Known problem: iw phy phy0 info shows:
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28567 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28564 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28563 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Based on a patch by dongyuqi <729650915@qq.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28277 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27310 3c298f89-4303-0410-b956-a3cf2f4a3e73
|