Age | Commit message (Collapse) | Author |
|
per-target base-file overlays to work correctly
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27138 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Having this file prevents the possibility of having target-specific
fstab config files (as target/linux/${target}/base-files/etc/config/fstab).
There is no need of a non-working example file on the target anyway.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27136 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
virtual interfaces
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27132 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
interface was found
eliminates unnecessary flash write cycles at every boot
patch by Peter Wagner (tripolar)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27127 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27126 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27125 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27117 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
<jim.cromie@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27109 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27103 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
This patch is already incorporated into the original source code.
closes #9499
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27100 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
If the string received from the ADSL firmware is missing \n, add it in.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27096 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Signed-off-by: Alexey Torkhov <atorkhov@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27095 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27084 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27071 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27046 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
The pata-cs5535/pata-cs5536 driver is actually fairly rare: it only gets used on embedded platforms. Therefore, we remove it from the generic x86 configuration.
Also, add definitions for other useful geode modules (high-res timers, MFGPT timers, etc).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27037 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
work just as well, and will use a lot less memory
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27029 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
* backport 2.6.8 patches to .39 / .32.33
* remove lqtapi
* bump tapi/dsl to .39
* migrate to new ltq_ style api
* add amazon_se support
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27026 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27025 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
introduce connection stability issues
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27024 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27022 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27021 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
* Add missing config symbols
* Update package/kernel for 2.6.39
CONFIG_BT_L2CAP=y and CONFIG_BT_SCO=y are set to build them into the bluetooth module.
Thank you Jonas Gorski for the patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27010 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27000 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26999 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26996 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Signed-off-by: Christoph König <christoph.koenig@ikt.uni-hannover.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26995 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
issues on wifi re-configuration
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26990 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26986 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Add a missing dependency to kmod-crypto-iv. chainiv.ko and eseqiv.ko
from kmod-crypto-iv depend on crypto_blkcipher.ko from
kmod-crypto-manager.
Signed-off-by: Lars Hjersted <lars@hjersted.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26984 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
The attached patch for dnsmasq.init allows to assign a hostname to a
particular mac-address. It's useful to override the client supplied
hostname, especially if the client does not supply a hostname at all.
It corresponds to the following example in dnsmasq.conf.example:
# Always set the name of the host with hardware address
# 11:22:33:44:55:66 to be "fred"
#dhcp-host=11:22:33:44:55:66,fred
Regards
Mathias
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26983 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26977 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26970 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
to wrong operator precedence
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26968 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
makes it less confusing
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26961 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
broadcom-wl driver bound to ssb device with ssb driver probe
have osh handle struct pdev pointer value initialized with
ssb_device pointer. Later on pdev is used with legacy pci
dma api as pci_dev thus causing oops sometimes.
The patch replaces legacy pci dma api and pass relevant
device struct pointer to avoid crashes.
Signed-off-by: George Kashperko <george@znau.edu.ua>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26949 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
It was causing an occasional kernel oops.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26948 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26947 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26934 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26933 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Hi,
the attached patch makes ipcalc.sh accept IP/Netmask combinations in
CIDR notation. Before you could only do:
# sh ipcalc.sh 192.168.0.0 255.255.255.0 1 10
IP=192.168.0.0
NETMASK=255.255.255.0
BROADCAST=192.168.0.255
NETWORK=192.168.0.0
PREFIX=24
START=192.168.0.1
END=192.168.0.11
with this patch you can also execute it with:
sh ipcalc.sh 192.168.0.0/24 1 10
IP=192.168.0.0
NETMASK=255.255.255.0
BROADCAST=192.168.0.255
NETWORK=192.168.0.0
PREFIX=24
START=192.168.0.1
END=192.168.0.11
The patch is based on #1260 [1], i just changed one line to calculate
the START end END ips right. I wonder why that never got included. If
there is no reason not to do i would like to ask you to commit that
patch, because its a functionality i (and probably others) miss quite often.
Btw, i also fixed 4 useless tabs, that might look a bit strange in the
patch.
Regards, Manuel
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26930 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
override (thx, KanjiMonster)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26927 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
requests in ad-hoc mode without creating too much spam
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26923 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
* add missing aes dependency to mv_cesa
Signed-off-by: Jan Willies <jan@willies.info>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26920 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
some instances
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26915 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26913 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26912 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
Since the oldest kernel in trunk is 2.6.30 the modules always use the
newer names, so we can just use the _generic prefix directly.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26903 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
There's only 2.6, so it doesn't make sense to mention modules that are
2.4 only or for modules that they are available only for 2.6.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26902 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
With no 2.4 support in trunk, we can safely remove any 2.4 definitions for
kmods and merge the 2.6 definitions into the generic ones.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26901 3c298f89-4303-0410-b956-a3cf2f4a3e73
|