summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-11-13ar71xx: set MII interface speed from the set_speed callbacksjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29013 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13ar71xx: rename set_pll callback to set_speed in ag71xx_platform_datajuhosg
Also rename the corresponding callback functions. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29012 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13ar71xx: ag71xx: remove MII interface setup codejuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13ar71xx: configure MII interface type from ar71xx_setup_phy_if_modejuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29010 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13ar71xx: fix occasional kernel hangs during boot on AR934xjuhosg
The patch taken from the linux-mips mailing list. The Kernel hangs occasionally during boot after "Calibrating delay loop..". This is caused by the c0_compare_int_usable() routine in cevt-r4k.c returning false which causes the system to disable the timer and hang later. The false return happens because the routine is using a series of four calls to irq_disable_hazard() as a delay while it waits for the timer changes to propagate to the cp0 cause register. On newer MIPS cores, like the 74K, the series of irq_disable_hazard() calls turn into ehb instructions and can take as little as a few clock ticks for all 4 instructions. This is not enough of a delay, so the routine thinks the timer is not working. This fix uses up to a max number of cycle counter ticks for the delay and uses back_to_back_c0_hazard() instead of irq_disable_hazard() to handle the hazard condition between cp0 writes and cp0 reads. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29009 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13ar71xx: refresh kernel patchesjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29008 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13linux: update 3.1 to 3.1.1jogo
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29007 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: add uci-defaults code for handling ledsblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29004 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: add /lib/lantiq.sh and make hotplug handlers use itblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29003 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: rename ledsblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29002 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: split compat headers out of bsp header patchblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29001 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: adds hotplug handler for loading rt2x00 firmwareblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29000 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: adds hotplug handler for handling buttons and makes w303v work with itblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28999 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: cleanup default package selectionblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28998 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12lantiq: w303v has its rt2860 eep on the nor flash. tell compat-wireless how ↵blogic
to use it git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28994 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12kernel: ar8216: add support for the AR8236 switchjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12kernel: ar8216: move port vlan setup into a separate functionjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28992 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12package/base-files: enhance service functionsnico
* allow matching process by name (useful for processes changing it) * check if first argument is executable * fix function name used in error messages git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28991 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: use the button for WPS control on the DB120juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28990 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: register the second ethernet interface on the DB120 boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28989 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: implement SoC specific phy interface setupjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28988 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: move phy interface setup into a separate functionjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28987 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: register both MDIO bus on the DB120 boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28986 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: add AR934X specific MDIO registration codejuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28985 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: add a secondary mdio busjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28984 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: rename ar71xx_mdio_* structures to ar71xx_mdio0_*juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28983 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: add an id argument to ar71xx_add_device_mdiojuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28982 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: pass netdev and miidev pointer to ar71xx_add_device_dsajuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28981 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: add AR934x specific USB setupjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28980 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: register the first ethernet interface on the DB120 boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28979 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: allow to register ethernet interfaces for AR934Xjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28978 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: ag71xx: use fixed link parameters if the mii bus is not registeredjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28977 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: add AR934X specific bootstrap and reset register bitsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28976 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: add diag support for the DB120 boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28975 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: fix GPIO direction setup for AR934xjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28974 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: fix AR934X clock frequency calculationjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28973 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12package: add om2p-watchdog scriptjuhosg
Based on a patch by: Marek Lindner <lindner_marek@yahoo.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28972 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12ar71xx: generate ubootenv from uci-defaults instead of providing defconfigjuhosg
I noticed most of /etc/defconfig was replaced by /etc/uci-defaults, which is indeed much nicer. So I moved over ubootenv from having a defconfig-entry to also be generated from uci-defaults. Signed-off-by: Daniel Golle <dgolle@allnet.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28971 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11pjsip: bump to 1.10 and improve ltq_tapi backendblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28963 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11lantiq: improve falcon package selectionblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28962 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11lantiq: fix breakage introduced in 3.1 bumpblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28961 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11[package] base-files: now that the initial password is completely empty (and ↵jow
not primed with "!") adjust login.sh for it to make telnetd available again git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28943 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11package/base-files-network: fix udhcpc issues introduced in r28866 (closes: ↵nico
#10383) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28942 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11remove empty folder lqtapiblogic
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28941 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-10[package] mac80211: add antenna control api for b43jow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28940 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-10[package] acx-mac80211: update to 20111030florian
Fixes build failures with Linux 3.1+ git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28939 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-10[base-files]: nuke another 2.4 skeletonkaloz
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28937 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-10enable and use shadow passwords by defaultkaloz
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28936 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-10[base-files]: the empty root password should be empty ;)kaloz
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28935 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-10base-files, target: assign name to system timeserver section, makes it ↵jow
easier to set servers on the cli git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28933 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-17 18:59:39 +0000