summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-01-04ar71xx: add default LED configuration for the TL-MR3020juhosg
Also use the system LED for diagnostic. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29652 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-04ar71xx: add support for TP-Link TL-MR3020juhosg
This patch adds support for the TP-Link device TL-MR3020 which is very similiar to the TL-WR703N. The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions. Only four LEDs can be controlled via GPIO. The power LED is connected to the power supply. The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals of the sliding switch have been mapped to BTN_0 and BTN_1. I have also setup a wiki page with details here: http://wiki.openwrt.org/toh/tp-link/tl-mr3020 USB is working and has been tested with USB mass storage and USB UMTS stick. Wifi also seems to work. Ethernet is working too. Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29651 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-04firmware-utils/mktplinkfw: add support for TL-MR3020juhosg
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29650 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-04package: remove the om2p-watchdog packagejuhosg
Signed-off-by: Antonio Quartulli <ordex@autistici.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29649 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-04ar71xx: use the new om-watchdog package for OM2Pjuhosg
Signed-off-by: Antonio Quartulli <ordex@autistici.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29648 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-04package: add om-watchdog packagejuhosg
om2p-watchdog package is OM2P specific. However a similar watchdog mechanism exists on OM1P as well. This new package wants to substitute om2p-watchdog with a new one which is suitable either for OM1P and OM2P. Signed-off-by: Antonio Quartulli <ordex@autistici.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29647 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-04[toolchain] disable UCLIBC_HAS_XLOCALE and UCLIB_HAS_GLIBC_DIGIT_GROUPING if ↵jow
BUILD_NLS is on (#10735) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29646 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-04add CT target and TTL/HL match+targetjow
This patch adds the CT target for conntrack (enables manipulation of conntrack events and supercedes NOTRACK) as well as the TTL/HL target and match. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29645 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-04[netfilter] remove current RTSP supportjow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29643 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-03[generic] backport upstream commit e1738bd9cecc5c867b0e2996470c1ff20f66ba79 ↵jow
to affected kernels (#9802) commit 8efa88540635 (sch_sfq: avoid giving spurious NET_XMIT_CN signals) forgot to call qdisc_tree_decrease_qlen() to signal upper levels that a packet (from another flow) was dropped, leading to various problems. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29642 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-01ar71xx: add profile and build factory image for the Hornet-UB boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29637 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-01ar71xx: build images for the ALFA Network N2/N5 boardsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29636 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-01ar71xx: add support for the ALFA Network N2/N5 boardsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29635 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-01[package] iwinfo: factor txpower offset into info display output, recompile ↵jow
if driver selection changes git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29634 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-01[toolchain] if CONFIG_BUILD_NLS is selected, compile uClibc with locale supportjow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29633 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boardsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29631 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31ar71xx: enable SWCONFIG_LEDSjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29630 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31package/base-files: add support for the switch LED triggerjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29629 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31package/base-files: use case statement in led init scriptjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29628 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31kernel: swconfig: introduce a generic switch LED triggerjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29627 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31ar71xx: ag71xx: implement get_port_{link,stats} callbacksjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29626 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31kernel: swconfig: add get_port_{link,stats} callbacksjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29625 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31ar71xx: fix LEDs on the WRT400Njuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29624 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-28ramips: rt288x: add support for the Belkin F5D8235-4 v1 boardjuhosg
Patch-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29617 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-28ramips: rt288x: change base address and window size of flash bank 0juhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29616 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-28ramips: rt305x: add support for the ALFA Networks W502U (R36) boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29615 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-27ar71xx: enable sysupgrade support for airrouterjuhosg
Works for me! ;-) Patch-by: Russell Senior <russell@personaltelco.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29614 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-27ar71xx: fix sysupgrade on PB42/PB44 boardsjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29613 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-27ramips: rt288x: add support for the Buffalo WLI-TX4-AG300N boardjuhosg
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29612 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-25[package] add usbreset - a small simple utility to send port rests to ↵jow
selected usb devices (#10394) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29611 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-25[generic] add missing config symboljow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29610 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-25[netfilter] package CT targetjow
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29609 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-23mac80211: clean up init, remove some redundant checks, fix tx power init ↵nbd
(#10113) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29606 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-23brcm47xx: fix usb on more recent bcma based devices.hauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29605 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-23ramips: initial support for Sitecom WL-351 v1 002juhosg
This add support for the Sitecom WL-351 v1 002. In principle the Engenius ESR9850 should also work with this, but I don't have the hardware to test it. Since an external gigabit switch (RTL8366RB) is used, I had to modify the ramips_esw driver to add a 'bypass' mode, which just configures it to not filter the vlan tags. Also two initialization words (FCT2 and FPA2) are set to different values by u-boot than what the driver is using and it only seems to work correctly when they not overridden by the driver, so I added them to the platform specific data as reg_initval_fct2 and reg_initval_fpa2. With this wired lan works as expected, however I'm still having some trouble with the wireless lan: It only works after I rmmod & re-insmod rt2800pci and then reconfigure it in the webinterface, but not directly after rebooting. The symptom of this is wpad saying: Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1) Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN) Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated But wpa_supplicant on the client saying: Authentication with <wl351mac> timed out. Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29604 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-23ramips: add support for the Senao/EnGenius ESR-9753 boardjuhosg
Signed-off-by: Artur Wronowski <arteqw@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29603 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-23ramips: define firmware partition for Omnima MiniEMBWiFijuhosg
Patch-by: Ivan Ignjatic <ivan@omnima.co.uk> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29602 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-22kernel: enable magic sysrq by default, it does not add much to the kernel ↵nbd
image size, but is useful for debugging many kinds of hangs/crashes git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29600 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-22ar71xx: set a reserved bit that resets to 1 when writing the address table ↵nbd
control register on the ar7240 switch (should fix #10547) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29598 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-21ar71xx: add default network config for buffalo WZR-HP-G300NH2 and WZR-HP-G450Hjogo
Thanks netprince for reporting and testing. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29595 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-21[ar71xx] the mach file of the WZR-HP-G300NH2 accidentally claimed the mach ↵jow
id of the WZR-HP-AG300H, correct the id (#10649) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29593 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-20[package] base-files: add -b (--create-backup) option to sysupgrade, which ↵jow
generates a backup .tar.gz according to the user settings. This will also be reused by LuCI. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29587 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-20[package] firewall:jow
- introduce per-section "option enabled" which defaults to "1" - useful to disable rules or zones without having to delete them - annotate default traffic rules with names - bump version git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29577 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-19brcm47xx: remove patch starting adding brcm4716 to ssbhauke
brcm4716 is supported by bcma now we do not need this patch git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29576 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-19brcm47xx: add new usb driver for bcma bus and replace ssb usb driver.hauke
This new usb driver uses an extra device so the ehci and the ohci driver are not depending on ech other any more. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29575 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-19kernel: update bcma and ssb to version master-2011-12-16 from wireless-testinghauke
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29574 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-19brcm47xx: remove support for kernel 2.6.39hauke
There are problems with the patches for kernel 2.6.39 and I do not want to support two different sets of patches. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29573 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-19mac80211: deactivate mac80211 tracinghauke
Activating tracing on kernel <= 2.6.32 causes build errors. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29572 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-19ath9k: fix another tx locking issuenbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29570 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-19mac80211: fix powersave settingnbd
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29569 3c298f89-4303-0410-b956-a3cf2f4a3e73