diff options
Diffstat (limited to 'target')
4 files changed, 117 insertions, 57 deletions
diff --git a/target/linux/brcm47xx/patches-2.6.30/250-ohci-ssb-usb2.patch b/target/linux/brcm47xx/patches-2.6.30/250-ohci-ssb-usb2.patch index 85361ab740..065a16b386 100644 --- a/target/linux/brcm47xx/patches-2.6.30/250-ohci-ssb-usb2.patch +++ b/target/linux/brcm47xx/patches-2.6.30/250-ohci-ssb-usb2.patch @@ -1,40 +1,31 @@ ---- a/drivers/usb/host/ohci-ssb.c -+++ b/drivers/usb/host/ohci-ssb.c -@@ -106,10 +106,59 @@ static int ssb_ohci_attach(struct ssb_de +--- + drivers/usb/host/ohci-ssb.c | 39 ++++++++++++++++++++++++++++++++++++--- + 1 file changed, 36 insertions(+), 3 deletions(-) + +--- linux-2.6.28.10.orig/drivers/usb/host/ohci-ssb.c ++++ linux-2.6.28.10/drivers/usb/host/ohci-ssb.c +@@ -106,10 +106,42 @@ static int ssb_ohci_attach(struct ssb_de int err = -ENOMEM; u32 tmp, flags = 0; - if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) -+ /* -+ * THE FOLLOWING COMMENTS PRESERVED FROM GPL SOURCE RELEASE -+ * -+ * The USB core requires a special bit to be set during core -+ * reset to enable host (OHCI) mode. Resetting the SB core in -+ * pcibios_enable_device() is a hack for compatibility with -+ * vanilla usb-ohci so that it does not have to know about -+ * SB. A driver that wants to use the USB core in device mode -+ * should know about SB and should reset the bit back to 0 -+ * after calling pcibios_enable_device(). -+ */ -+ + if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) { ++ /* Put the device into host-mode. */ flags |= SSB_OHCI_TMSLOW_HOSTMODE; +- +- ssb_device_enable(dev, flags); + ssb_device_enable(dev, flags); -+ } -+ -+ /* -+ * USB 2.0 special considerations: -+ * -+ * 1. Since the core supports both OHCI and EHCI functions, it must -+ * only be reset once. -+ * -+ * 2. In addition to the standard SB reset sequence, the Host Control -+ * Register must be programmed to bring the USB core and various -+ * phy components out of reset. -+ */ -+ -+ else if (dev->id.coreid == SSB_DEV_USB20_HOST) { -+#warning FIX ME need test for core being up & exit ++ } else if (dev->id.coreid == SSB_DEV_USB20_HOST) { ++ /* ++ * USB 2.0 special considerations: ++ * ++ * 1. Since the core supports both OHCI and EHCI functions, it must ++ * only be reset once. ++ * ++ * 2. In addition to the standard SSB reset sequence, the Host Control ++ * Register must be programmed to bring the USB core and various ++ * phy components out of reset. ++ */ + ssb_device_enable(dev, 0); + ssb_write32(dev, 0x200, 0x7ff); + udelay(1); @@ -54,15 +45,12 @@ + tmp = ssb_read32(dev, 0x304); + printk("USB20H shim: 0x%0x\n", tmp); + } -+ } -+ else ++ } else + ssb_device_enable(dev, 0); -- ssb_device_enable(dev, flags); - hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev, dev_name(dev->dev)); -@@ -200,6 +249,7 @@ static int ssb_ohci_resume(struct ssb_de +@@ -200,6 +232,7 @@ static int ssb_ohci_resume(struct ssb_de static const struct ssb_device_id ssb_ohci_table[] = { SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV), SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV), diff --git a/target/linux/brcm47xx/patches-2.6.30/260-ohci-set-dma-mask.patch b/target/linux/brcm47xx/patches-2.6.30/260-ohci-set-dma-mask.patch index 0b9dd51603..6da3f10bf2 100644 --- a/target/linux/brcm47xx/patches-2.6.30/260-ohci-set-dma-mask.patch +++ b/target/linux/brcm47xx/patches-2.6.30/260-ohci-set-dma-mask.patch @@ -1,14 +1,16 @@ ---- a/drivers/usb/host/ohci-ssb.c -+++ b/drivers/usb/host/ohci-ssb.c -@@ -159,6 +159,11 @@ static int ssb_ohci_attach(struct ssb_de - else - ssb_device_enable(dev, 0); +--- + drivers/usb/host/ohci-ssb.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- linux-2.6.28.10.orig/drivers/usb/host/ohci-ssb.c ++++ linux-2.6.28.10/drivers/usb/host/ohci-ssb.c +@@ -106,6 +106,9 @@ static int ssb_ohci_attach(struct ssb_de + int err = -ENOMEM; + u32 tmp, flags = 0; -+ /* -+ * Set dma mask - 32 bit mask is just an assumption -+ */ -+ if (ssb_dma_set_mask(dev, DMA_32BIT_MASK)) -+ return -EOPNOTSUPP; - - hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev, - dev_name(dev->dev)); ++ if (ssb_dma_set_mask(dev, DMA_32BIT_MASK)) ++ return -EOPNOTSUPP; ++ + if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) { + /* Put the device into host-mode. */ + flags |= SSB_OHCI_TMSLOW_HOSTMODE; diff --git a/target/linux/brcm47xx/patches-2.6.30/270-ehci-ssb.patch b/target/linux/brcm47xx/patches-2.6.30/270-ehci-ssb.patch index 02e44ca5f6..e64dc4b1bd 100644 --- a/target/linux/brcm47xx/patches-2.6.30/270-ehci-ssb.patch +++ b/target/linux/brcm47xx/patches-2.6.30/270-ehci-ssb.patch @@ -1,5 +1,12 @@ ---- a/drivers/usb/host/Kconfig -+++ b/drivers/usb/host/Kconfig +--- + drivers/usb/host/Kconfig | 13 ++ + drivers/usb/host/ehci-hcd.c | 12 ++ + drivers/usb/host/ehci-ssb.c | 201 ++++++++++++++++++++++++++++++++++++++++++++ + drivers/usb/host/ohci-ssb.c | 23 +++++ + 4 files changed, 247 insertions(+), 2 deletions(-) + +--- linux-2.6.30.5.orig/drivers/usb/host/Kconfig ++++ linux-2.6.30.5/drivers/usb/host/Kconfig @@ -106,6 +106,19 @@ config USB_OXU210HP_HCD To compile this driver as a module, choose M here: the module will be called oxu210hp-hcd. @@ -20,8 +27,8 @@ config USB_ISP116X_HCD tristate "ISP116X HCD support" depends on USB ---- a/drivers/usb/host/ehci-hcd.c -+++ b/drivers/usb/host/ehci-hcd.c +--- linux-2.6.30.5.orig/drivers/usb/host/ehci-hcd.c ++++ linux-2.6.30.5/drivers/usb/host/ehci-hcd.c @@ -1072,8 +1072,16 @@ MODULE_LICENSE ("GPL"); #define PLATFORM_DRIVER ixp4xx_ehci_driver #endif @@ -42,7 +49,7 @@ #endif --- /dev/null -+++ b/drivers/usb/host/ehci-ssb.c ++++ linux-2.6.30.5/drivers/usb/host/ehci-ssb.c @@ -0,0 +1,201 @@ +/* + * Sonics Silicon Backplane @@ -207,7 +214,7 @@ + u32 tmp, flags = 0; + + hcd = usb_create_hcd(&ssb_ehci_hc_driver, dev->dev, -+ dev_name(dev->dev)); ++ dev->dev->bus_id); + if (!hcd) + goto err_dev_disable; + @@ -245,8 +252,8 @@ + SSB_DEVTABLE_END +}; +MODULE_DEVICE_TABLE(ssb, ssb_ehci_table); ---- a/drivers/usb/host/ohci-ssb.c -+++ b/drivers/usb/host/ohci-ssb.c +--- linux-2.6.30.5.orig/drivers/usb/host/ohci-ssb.c ++++ linux-2.6.30.5/drivers/usb/host/ohci-ssb.c @@ -17,6 +17,8 @@ */ #include <linux/ssb/ssb.h> @@ -290,7 +297,7 @@ static int ssb_ohci_attach(struct ssb_device *dev) { struct ssb_ohci_device *ohcidev; -@@ -184,6 +199,14 @@ static int ssb_ohci_attach(struct ssb_de +@@ -165,6 +180,14 @@ static int ssb_ohci_attach(struct ssb_de ssb_set_drvdata(dev, hcd); diff --git a/target/linux/brcm47xx/patches-2.6.30/275-usb2-bcm5354-init.patch b/target/linux/brcm47xx/patches-2.6.30/275-usb2-bcm5354-init.patch new file mode 100644 index 0000000000..a166329150 --- /dev/null +++ b/target/linux/brcm47xx/patches-2.6.30/275-usb2-bcm5354-init.patch @@ -0,0 +1,63 @@ +This patch significantly improves the reliability of high speed +usb writes on the bcm5354. It implements a work around for version 2 +of the usb20 core that was cribbed from the GPL sources for the +Asus wl500gpv2 and verified against the wl520gu sources. + +Reference: +GPL/WL-520gu-NewUI/src/linux/linux/arch/mips/brcm-boards/bcm947xx/pcibios.c +GPL/WL-500gPV2-NewUI/src/linux/linux/arch/mips/brcm-boards/bcm947xx/pcibios.c + +Signed-off-by: Steve Brown <sbrown@cortland.com> + +--- + drivers/usb/host/ohci-ssb.c | 37 +++++++++++++++++++++++-------------- + 1 file changed, 23 insertions(+), 14 deletions(-) + +--- linux-2.6.28.10.orig/drivers/usb/host/ohci-ssb.c ++++ linux-2.6.28.10/drivers/usb/host/ohci-ssb.c +@@ -141,22 +141,31 @@ static int ssb_ohci_attach(struct ssb_de + */ + ssb_device_enable(dev, 0); + ssb_write32(dev, 0x200, 0x7ff); ++ ++ /* Change Flush control reg */ ++ tmp = ssb_read32(dev, 0x400); ++ tmp &= ~8; ++ ssb_write32(dev, 0x400, tmp); ++ tmp = ssb_read32(dev, 0x400); ++ ++ /* Change Shim control reg */ ++ tmp = ssb_read32(dev, 0x304); ++ tmp &= ~0x100; ++ ssb_write32(dev, 0x304, tmp); ++ tmp = ssb_read32(dev, 0x304); ++ + udelay(1); +- if (dev->id.revision == 1) { // bug in rev 1 + +- /* Change Flush control reg */ +- tmp = ssb_read32(dev, 0x400); +- tmp &= ~8; +- ssb_write32(dev, 0x400, tmp); +- tmp = ssb_read32(dev, 0x400); +- printk("USB20H fcr: 0x%0x\n", tmp); +- +- /* Change Shim control reg */ +- tmp = ssb_read32(dev, 0x304); +- tmp &= ~0x100; +- ssb_write32(dev, 0x304, tmp); +- tmp = ssb_read32(dev, 0x304); +- printk("USB20H shim: 0x%0x\n", tmp); ++ /* Work around for 5354 failures */ ++ if ((dev->id.revision == 2) && (dev->bus->chip_id == 0x5354)) { ++ /* Change syn01 reg */ ++ tmp = 0x00fe00fe; ++ ssb_write32(dev, 0x894, tmp); ++ ++ /* Change syn03 reg */ ++ tmp = ssb_read32(dev, 0x89c); ++ tmp |= 0x1; ++ ssb_write32(dev, 0x89c, tmp); + } + } else + ssb_device_enable(dev, 0); |