diff options
Diffstat (limited to 'target/linux/kirkwood/patches-3.3')
5 files changed, 0 insertions, 777 deletions
diff --git a/target/linux/kirkwood/patches-3.3/001-openwrt_partition_map.patch b/target/linux/kirkwood/patches-3.3/001-openwrt_partition_map.patch deleted file mode 100644 index 0f94adc343..0000000000 --- a/target/linux/kirkwood/patches-3.3/001-openwrt_partition_map.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm/mach-kirkwood/sheevaplug-setup.c -+++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c -@@ -33,7 +33,7 @@ static struct mtd_partition sheevaplug_n - .offset = MTDPART_OFS_NXTBLK, - .size = SZ_4M - }, { -- .name = "root", -+ .name = "rootfs", - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL - }, diff --git a/target/linux/kirkwood/patches-3.3/002-mvsdio_delay.patch b/target/linux/kirkwood/patches-3.3/002-mvsdio_delay.patch deleted file mode 100644 index 46e2a5646c..0000000000 --- a/target/linux/kirkwood/patches-3.3/002-mvsdio_delay.patch +++ /dev/null @@ -1,32 +0,0 @@ ---- a/drivers/mmc/core/sd.c -+++ b/drivers/mmc/core/sd.c -@@ -389,6 +389,15 @@ int mmc_sd_switch_hs(struct mmc_card *ca - return -ENOMEM; - } - -+ /* -+ * Some SDHC cards, notably those with a Sandisk SD controller -+ * (also found in Kingston products) need a bit of slack -+ * before successfully handling the SWITCH command. So far, -+ * cards identifying themselves as "SD04G" and "SD08G" are -+ * affected -+ */ -+ udelay(1000); -+ - err = mmc_sd_switch(card, 1, 0, 1, status); - if (err) - goto out; ---- a/drivers/mmc/core/core.c -+++ b/drivers/mmc/core/core.c -@@ -529,9 +529,9 @@ void mmc_set_data_timeout(struct mmc_dat - * The limit is really 250 ms, but that is - * insufficient for some crappy cards. - */ -- limit_us = 300000; -+ limit_us = 500000; - else -- limit_us = 100000; -+ limit_us = 200000; - - /* - * SDHC cards always use these fixed values. diff --git a/target/linux/kirkwood/patches-3.3/200-iconnect.patch b/target/linux/kirkwood/patches-3.3/200-iconnect.patch deleted file mode 100644 index 5a46ee780f..0000000000 --- a/target/linux/kirkwood/patches-3.3/200-iconnect.patch +++ /dev/null @@ -1,218 +0,0 @@ ---- a/arch/arm/mach-kirkwood/Makefile -+++ b/arch/arm/mach-kirkwood/Makefile -@@ -8,6 +8,7 @@ obj-$(CONFIG_MACH_SHEEVAPLUG) += sheeva - obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o - obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o - obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o -+obj-$(CONFIG_MACH_ICONNECT) += iconnect-setup.o - obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o - obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o - obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o ---- a/arch/arm/mach-kirkwood/Kconfig -+++ b/arch/arm/mach-kirkwood/Kconfig -@@ -130,6 +130,12 @@ config MACH_T5325 - Say 'Y' here if you want your kernel to support the - HP t5325 Thin Client. - -+config MACH_ICONNECT -+ bool "Iomega iConnect Wireless" -+ help -+ Say 'Y' here if you want your kernel to support the -+ Iomega iConnect Wireless. -+ - endmenu - - endif ---- /dev/null -+++ b/arch/arm/mach-kirkwood/iconnect-setup.c -@@ -0,0 +1,190 @@ -+/* -+ * arch/arm/mach-kirkwood/iconnect-setup.c -+ * -+ * Iomega iConnect Wireless -+ * -+ * This file is licensed under the terms of the GNU General Public -+ * License version 2. This program is licensed "as is" without any -+ * warranty of any kind, whether express or implied. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+#include <linux/irq.h> -+#include <linux/mtd/partitions.h> -+#include <linux/mv643xx_eth.h> -+#include <linux/ethtool.h> -+#include <linux/gpio.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+#include <linux/leds.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <mach/kirkwood.h> -+#include "common.h" -+#include "mpp.h" -+ -+static struct mtd_partition iconnect_nand_parts[] = { -+ { -+ .name = "u-boot", -+ .offset = 0, -+ .size = SZ_1M -+ }, { -+ .name = "uImage", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = SZ_1M + SZ_2M -+ }, { -+ .name = "rootfs", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = SZ_32M, -+ }, { -+ .name = "data", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL -+ }, -+}; -+ -+static struct mv643xx_eth_platform_data iconnect_ge00_data = { -+ .phy_addr = MV643XX_ETH_PHY_ADDR(11), -+}; -+ -+static struct gpio_led iconnect_led_pins[] = { -+ { -+ .name = "iconnect:blue:power", -+ .default_trigger = "default-on", -+ .gpio = 42, -+ }, -+ { -+ .name = "iconnect:red:power", -+ .gpio = 43, -+ }, -+ { -+ .name = "iconnect:blue:usb1", -+ .gpio = 44, -+ }, -+ { -+ .name = "iconnect:blue:usb2", -+ .gpio = 45, -+ }, -+ { -+ .name = "iconnect:blue:usb3", -+ .gpio = 46, -+ }, -+ { -+ .name = "iconnect:blue:usb4", -+ .gpio = 47, -+ }, -+ { -+ .name = "iconnect:blue:otb", -+ .gpio = 48, -+ }, -+}; -+ -+static struct gpio_led_platform_data iconnect_led_data = { -+ .leds = iconnect_led_pins, -+ .num_leds = ARRAY_SIZE(iconnect_led_pins), -+}; -+ -+static struct platform_device iconnect_leds = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev = { -+ .platform_data = &iconnect_led_data, -+ } -+}; -+ -+#define ICONNECT_GPIO_KEY_RESET 12 -+#define ICONNECT_GPIO_KEY_OTB 35 -+ -+#define ICONNECT_SW_RESET 0x00 -+#define ICONNECT_SW_OTB 0x01 -+ -+static struct gpio_keys_button iconnect_buttons[] = { -+ { -+ .type = EV_SW, -+ .code = ICONNECT_SW_RESET, -+ .gpio = ICONNECT_GPIO_KEY_RESET, -+ .desc = "Reset Button", -+ .active_low = 1, -+ .debounce_interval = 100, -+ }, -+ { -+ .type = EV_SW, -+ .code = ICONNECT_SW_OTB, -+ .gpio = ICONNECT_GPIO_KEY_OTB, -+ .desc = "OTB Button", -+ .active_low = 1, -+ .debounce_interval = 100, -+ }, -+}; -+ -+static struct gpio_keys_platform_data iconnect_button_data = { -+ .buttons = iconnect_buttons, -+ .nbuttons = ARRAY_SIZE(iconnect_buttons), -+}; -+ -+static struct platform_device iconnect_button_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .num_resources = 0, -+ .dev = { -+ .platform_data = &iconnect_button_data, -+ }, -+}; -+ -+static unsigned int iconnect_mpp_config[] __initdata = { -+ MPP12_GPIO, /*Input for reset button*/ -+ MPP35_GPIO, /*Input for OTB button*/ -+ MPP42_GPIO, -+ MPP43_GPIO, -+ MPP44_GPIO, -+ MPP45_GPIO, -+ MPP46_GPIO, -+ MPP47_GPIO, -+ MPP48_GPIO, -+ 0 -+}; -+ -+static void __init iconnect_init(void) -+{ -+ u32 dev, rev; -+ -+ /* -+ * Basic setup. Needs to be called early. -+ */ -+ kirkwood_init(); -+ kirkwood_mpp_conf(iconnect_mpp_config); -+ -+ kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25); -+ kirkwood_ehci_init(); -+ -+ kirkwood_ge00_init(&iconnect_ge00_data); -+ kirkwood_pcie_id(&dev, &rev); -+ -+ kirkwood_uart0_init(); -+ kirkwood_i2c_init(); -+ -+ platform_device_register(&iconnect_leds); -+ platform_device_register(&iconnect_button_device); -+} -+ -+static int __init iconnect_pci_init(void) -+{ -+ if (machine_is_iconnect()) -+ kirkwood_pcie_init(KW_PCIE0); -+ -+ return 0; -+} -+subsys_initcall(iconnect_pci_init); -+ -+ -+MACHINE_START(ICONNECT, "Iomega iConnect Wireless") -+ .atag_offset = 0x100, -+ .init_machine = iconnect_init, -+ .map_io = kirkwood_map_io, -+ .init_early = kirkwood_init_early, -+ .init_irq = kirkwood_init_irq, -+ .timer = &kirkwood_timer, -+ .restart = kirkwood_restart, -+MACHINE_END diff --git a/target/linux/kirkwood/patches-3.3/201-raidsonic-IB-NAS62x0-support.patch b/target/linux/kirkwood/patches-3.3/201-raidsonic-IB-NAS62x0-support.patch deleted file mode 100644 index b7fcb04a9b..0000000000 --- a/target/linux/kirkwood/patches-3.3/201-raidsonic-IB-NAS62x0-support.patch +++ /dev/null @@ -1,216 +0,0 @@ ---- /dev/null -+++ b/arch/arm/mach-kirkwood/nas6210-setup.c -@@ -0,0 +1,189 @@ -+/* -+ * arch/arm/mach-kirkwood/nas6210-setup.c -+ * -+ * Raidsonic ICYBOX NAS6210 Board Setup -+ * -+ * This file is licensed under the terms of the GNU General Public -+ * License version 2. This program is licensed "as is" without any -+ * warranty of any kind, whether express or implied. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+#include <linux/ata_platform.h> -+#include <linux/mtd/partitions.h> -+#include <linux/mv643xx_eth.h> -+#include <linux/gpio.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+#include <linux/leds.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <mach/kirkwood.h> -+#include "common.h" -+#include "mpp.h" -+ -+#define NAS6210_GPIO_POWER_OFF 24 -+ -+static struct mtd_partition nas6210_nand_parts[] = { -+ { -+ .name = "uboot", -+ .offset = 0, -+ .size = SZ_512K -+ }, { -+ .name = "uboot_env", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = SZ_128K -+ }, { -+ .name = "kernel", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 3 * SZ_1M -+ }, { -+ .name = "rootfs", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL -+ }, -+}; -+ -+static struct mv643xx_eth_platform_data nas6210_ge00_data = { -+ .phy_addr = MV643XX_ETH_PHY_ADDR(8), -+}; -+ -+static struct mv_sata_platform_data nas6210_sata_data = { -+ .n_ports = 2, -+}; -+ -+static struct gpio_led nas6210_led_pins[] = { -+ { -+ .name = "status:green:power", -+ .default_trigger = "default-on", -+ .gpio = 25, -+ .active_low = 0, -+ }, -+ { -+ .name = "status:red:power", -+ .default_trigger = "none", -+ .gpio = 22, -+ .active_low = 0, -+ }, -+ { -+ .name = "status:red:usb_copy", -+ .default_trigger = "none", -+ .gpio = 27, -+ .active_low = 0, -+ }, -+}; -+ -+static struct gpio_led_platform_data nas6210_led_data = { -+ .leds = nas6210_led_pins, -+ .num_leds = ARRAY_SIZE(nas6210_led_pins), -+}; -+ -+static struct platform_device nas6210_leds = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev = { -+ .platform_data = &nas6210_led_data, -+ } -+}; -+ -+static struct gpio_keys_button nas6210_buttons[] = { -+ { -+ .code = KEY_COPY, -+ .gpio = 29, -+ .desc = "USB Copy", -+ .active_low = 1, -+ }, -+ { -+ .code = KEY_RESTART, -+ .gpio = 28, -+ .desc = "Reset", -+ .active_low = 1, -+ }, -+}; -+ -+static struct gpio_keys_platform_data nas6210_button_data = { -+ .buttons = nas6210_buttons, -+ .nbuttons = ARRAY_SIZE(nas6210_buttons), -+}; -+ -+static struct platform_device nas6210_button_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .num_resources = 0, -+ .dev = { -+ .platform_data = &nas6210_button_data, -+ } -+}; -+ -+static unsigned int nas6210_mpp_config[] __initdata = { -+ MPP0_NF_IO2, -+ MPP1_NF_IO3, -+ MPP2_NF_IO4, -+ MPP3_NF_IO5, -+ MPP4_NF_IO6, -+ MPP5_NF_IO7, -+ MPP18_NF_IO0, -+ MPP19_NF_IO1, -+ MPP22_GPIO, /* Power LED red */ -+ MPP24_GPIO, /* Power off device */ -+ MPP25_GPIO, /* Power LED green */ -+ MPP27_GPIO, /* USB transfer LED */ -+ MPP28_GPIO, /* Reset button */ -+ MPP29_GPIO, /* USB Copy button */ -+ 0 -+}; -+ -+static void nas6210_power_off(void) -+{ -+ gpio_set_value(NAS6210_GPIO_POWER_OFF, 1); -+} -+ -+static void __init nas6210_init(void) -+{ -+ /* -+ * Basic setup. Needs to be called early. -+ */ -+ kirkwood_init(); -+ kirkwood_mpp_conf(nas6210_mpp_config); -+ -+ kirkwood_nand_init(ARRAY_AND_SIZE(nas6210_nand_parts), 25); -+ kirkwood_ehci_init(); -+ kirkwood_ge00_init(&nas6210_ge00_data); -+ kirkwood_sata_init(&nas6210_sata_data); -+ kirkwood_uart0_init(); -+ platform_device_register(&nas6210_leds); -+ platform_device_register(&nas6210_button_device); -+ if (gpio_request(NAS6210_GPIO_POWER_OFF, "power-off") == 0 && -+ gpio_direction_output(NAS6210_GPIO_POWER_OFF, 0) == 0) -+ pm_power_off = nas6210_power_off; -+ else -+ pr_err("nas6210: failed to configure power-off GPIO\n"); -+} -+ -+static int __init nas6210_pci_init(void) -+{ -+ if (machine_is_nas6210()) { -+ u32 dev, rev; -+ -+ kirkwood_pcie_id(&dev, &rev); -+ if (dev == MV88F6282_DEV_ID) -+ kirkwood_pcie_init(KW_PCIE1 | KW_PCIE0); -+ else -+ kirkwood_pcie_init(KW_PCIE0); -+ } -+ -+ return 0; -+} -+subsys_initcall(nas6210_pci_init); -+ -+MACHINE_START(NAS6210, "RaidSonic ICY BOX IB-NAS6210") -+ /* Maintainer: <gmbnomis at gmail dot com> */ -+ .atag_offset = 0x100, -+ .init_machine = nas6210_init, -+ .map_io = kirkwood_map_io, -+ .init_early = kirkwood_init_early, -+ .init_irq = kirkwood_init_irq, -+ .timer = &kirkwood_timer, -+MACHINE_END ---- a/arch/arm/mach-kirkwood/Kconfig -+++ b/arch/arm/mach-kirkwood/Kconfig -@@ -136,6 +136,12 @@ config MACH_ICONNECT - Say 'Y' here if you want your kernel to support the - Iomega iConnect Wireless. - -+config MACH_NAS6210 -+ bool "RaidSonic ICY BOX IB-NAS6210" -+ help -+ Say 'Y' here if you want your kernel to support the -+ RaidSonic ICY BOX IB-NAS6210 device. -+ - endmenu - - endif ---- a/arch/arm/mach-kirkwood/Makefile -+++ b/arch/arm/mach-kirkwood/Makefile -@@ -19,5 +19,6 @@ obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2 - obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o - obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o - obj-$(CONFIG_MACH_T5325) += t5325-setup.o -+obj-$(CONFIG_MACH_NAS6210) += nas6210-setup.o - - obj-$(CONFIG_CPU_IDLE) += cpuidle.o diff --git a/target/linux/kirkwood/patches-3.3/202-zyxel-nsa-310.patch b/target/linux/kirkwood/patches-3.3/202-zyxel-nsa-310.patch deleted file mode 100644 index cb842976e7..0000000000 --- a/target/linux/kirkwood/patches-3.3/202-zyxel-nsa-310.patch +++ /dev/null @@ -1,300 +0,0 @@ ---- a/arch/arm/mach-kirkwood/Kconfig -+++ b/arch/arm/mach-kirkwood/Kconfig -@@ -142,6 +142,12 @@ config MACH_NAS6210 - Say 'Y' here if you want your kernel to support the - RaidSonic ICY BOX IB-NAS6210 device. - -+config MACH_NSA310 -+ bool "ZyXEL NSA-310" -+ help -+ Say 'Y' here if you want your kernel to support the -+ ZyXEL NSA-310 board. -+ - endmenu - - endif ---- a/arch/arm/mach-kirkwood/Makefile -+++ b/arch/arm/mach-kirkwood/Makefile -@@ -20,5 +20,6 @@ obj-$(CONFIG_MACH_NET2BIG_V2) += netxbi - obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o - obj-$(CONFIG_MACH_T5325) += t5325-setup.o - obj-$(CONFIG_MACH_NAS6210) += nas6210-setup.o -+obj-$(CONFIG_MACH_NSA310) += nsa-310-setup.o - - obj-$(CONFIG_CPU_IDLE) += cpuidle.o ---- /dev/null -+++ b/arch/arm/mach-kirkwood/nsa-310-setup.c -@@ -0,0 +1,273 @@ -+/* -+ * arch/arm/mach-kirkwood/nsa-310-setup.c -+ * -+ * ZyXEL NSA-310 Setup -+ * -+ * This file is licensed under the terms of the GNU General Public -+ * License version 2. This program is licensed "as is" without any -+ * warranty of any kind, whether express or implied. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+#include <linux/ata_platform.h> -+#include <linux/i2c.h> -+#include <linux/mtd/mtd.h> -+#include <linux/mtd/partitions.h> -+#include <linux/gpio.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+#include <linux/leds.h> -+#include <linux/delay.h> -+ -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <mach/kirkwood.h> -+#include "common.h" -+#include "mpp.h" -+ -+#define NSA310_GPIO_LED_ESATA_GREEN 12 -+#define NSA310_GPIO_LED_ESATA_RED 13 -+#define NSA310_GPIO_LED_USB_GREEN 15 -+#define NSA310_GPIO_LED_USB_RED 16 -+#define NSA310_GPIO_USB_POWER_OFF 21 -+#define NSA310_GPIO_LED_SYS_GREEN 28 -+#define NSA310_GPIO_LED_SYS_RED 29 -+#define NSA310_GPIO_KEY_RESTART 36 -+#define NSA310_GPIO_KEY_COPY 37 -+#define NSA310_GPIO_LED_COPY_GREEN 39 -+#define NSA310_GPIO_LED_COPY_RED 40 -+#define NSA310_GPIO_LED_HDD_GREEN 41 -+#define NSA310_GPIO_LED_HDD_RED 42 -+#define NSA310_GPIO_BUZZER 44 -+#define NSA310_GPIO_KEY_POWER 46 -+#define NSA310_GPIO_POWER_OFF 48 -+ -+ -+static unsigned int nsa310_mpp_config[] __initdata = { -+ MPP12_GPIO, -+ MPP13_GPIO, -+ MPP15_GPIO, -+ MPP16_GPIO, -+ MPP21_GPIO, -+ MPP28_GPIO, -+ MPP29_GPIO, -+ MPP36_GPIO, -+ MPP37_GPIO, -+ MPP39_GPIO, -+ MPP40_GPIO, -+ MPP41_GPIO, -+ MPP42_GPIO, -+ MPP44_GPIO, -+ MPP46_GPIO, -+ MPP48_GPIO, -+ 0 -+}; -+ -+static struct mtd_partition nsa310_mtd_parts[] = { -+ { -+ .name = "uboot", -+ .offset = 0, -+ .size = 0x100000, -+ .mask_flags = MTD_WRITEABLE, -+ }, { -+ .name = "uboot_env", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 0x80000, -+ }, { -+ .name = "key_store", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 0x80000, -+ }, { -+ .name = "info", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 0x80000, -+ }, { -+ .name = "etc", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 0xa00000, -+ }, { -+ .name = "kernel_1", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 0xa00000, -+ }, { -+ .name = "rootfs1", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 0x2fc0000, -+ }, { -+ .name = "kernel_2", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 0xa00000, -+ }, { -+ .name = "rootfs2", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 0x2fc0000, -+ }, -+}; -+ -+static struct gpio_led nsa310_leds[] = { -+ { -+ .name = "nsa310:green:sys", -+ .gpio = NSA310_GPIO_LED_SYS_GREEN, -+ }, { -+ .name = "nsa310:red:sys", -+ .gpio = NSA310_GPIO_LED_SYS_RED, -+ }, { -+ .name = "nsa310:green:hdd", -+ .gpio = NSA310_GPIO_LED_HDD_GREEN, -+ }, { -+ .name = "nsa310:red:hdd", -+ .gpio = NSA310_GPIO_LED_HDD_RED, -+ }, { -+ .name = "nsa310:green:esata", -+ .gpio = NSA310_GPIO_LED_ESATA_GREEN, -+ }, { -+ .name = "nsa310:red:esata", -+ .gpio = NSA310_GPIO_LED_ESATA_RED, -+ }, { -+ .name = "nsa310:green:usb", -+ .gpio = NSA310_GPIO_LED_USB_GREEN, -+ }, { -+ .name = "nsa310:red:usb", -+ .gpio = NSA310_GPIO_LED_USB_RED, -+ }, { -+ .name = "nsa310:green:copy", -+ .gpio = NSA310_GPIO_LED_COPY_GREEN, -+ }, { -+ .name = "nsa310:red:copy", -+ .gpio = NSA310_GPIO_LED_COPY_RED, -+ }, -+}; -+ -+static struct gpio_led_platform_data nsa310_leds_data = { -+ .leds = nsa310_leds, -+ .num_leds = ARRAY_SIZE(nsa310_leds), -+}; -+ -+static struct platform_device nsa310_leds_device = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev = { -+ .platform_data = &nsa310_leds_data, -+ } -+}; -+ -+static struct gpio_keys_button nsa310_buttons[] = { -+ { -+ .desc = "Power Button", -+ .code = KEY_POWER, -+ .type = EV_KEY, -+ .gpio = NSA310_GPIO_KEY_POWER, -+ .debounce_interval = 1000, -+ }, { -+ .desc = "Copy Button", -+ .code = KEY_COPY, -+ .type = EV_KEY, -+ .gpio = NSA310_GPIO_KEY_COPY, -+ .active_low = 1, -+ .debounce_interval = 1000, -+ }, { -+ .desc = "Reset Button", -+ .code = KEY_RESTART, -+ .type = EV_KEY, -+ .gpio = NSA310_GPIO_KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = 1000, -+ }, -+}; -+ -+static struct gpio_keys_platform_data nsa310_keys_data = { -+ .buttons = nsa310_buttons, -+ .nbuttons = ARRAY_SIZE(nsa310_buttons), -+}; -+ -+static struct platform_device nsa310_keys_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .dev = { -+ .platform_data = &nsa310_keys_data, -+ } -+}; -+ -+static struct i2c_board_info __initdata nsa310_i2c_info[] = { -+ { I2C_BOARD_INFO("adt7476", 0x2e) }, -+}; -+ -+static struct mv_sata_platform_data nsa310_sata_data = { -+ .n_ports = 2, -+}; -+ -+static void nsa310_power_off(void) -+{ -+ gpio_set_value(NSA310_GPIO_POWER_OFF, 1); -+} -+ -+static int __init nsa310_gpio_request(unsigned int gpio, unsigned long flags, -+ const char *label) -+{ -+ int err; -+ -+ err = gpio_request_one(gpio, flags, label); -+ if (err) -+ pr_err("NSA-310: can't setup GPIO%u (%s), err=%d\n", -+ gpio, label, err); -+ -+ return err; -+} -+ -+static void __init nsa310_gpio_init(void) -+{ -+ int err; -+ -+ err = nsa310_gpio_request(NSA310_GPIO_POWER_OFF, GPIOF_OUT_INIT_LOW, -+ "Power Off"); -+ if (!err) -+ pm_power_off = nsa310_power_off; -+ -+ nsa310_gpio_request(NSA310_GPIO_USB_POWER_OFF, GPIOF_OUT_INIT_LOW, -+ "USB Power Off"); -+} -+ -+static void __init nsa310_init(void) -+{ -+ u32 dev, rev; -+ -+ kirkwood_init(); -+ kirkwood_mpp_conf(nsa310_mpp_config); -+ -+ nsa310_gpio_init(); -+ -+ kirkwood_nand_init(ARRAY_AND_SIZE(nsa310_mtd_parts), 35); -+ kirkwood_ehci_init(); -+ -+ kirkwood_pcie_id(&dev, &rev); -+ -+ kirkwood_sata_init(&nsa310_sata_data); -+ kirkwood_uart0_init(); -+ -+ i2c_register_board_info(0, ARRAY_AND_SIZE(nsa310_i2c_info)); -+ kirkwood_i2c_init(); -+ -+ platform_device_register(&nsa310_leds_device); -+ platform_device_register(&nsa310_keys_device); -+} -+ -+static int __init nsa310_pci_init(void) -+{ -+ if (machine_is_nsa310()) -+ kirkwood_pcie_init(KW_PCIE0); -+ -+ return 0; -+} -+subsys_initcall(nsa310_pci_init); -+ -+MACHINE_START(NSA310, "ZyXEL NSA-310") -+ .atag_offset = 0x100, -+ .init_machine = nsa310_init, -+ .map_io = kirkwood_map_io, -+ .init_early = kirkwood_init_early, -+ .init_irq = kirkwood_init_irq, -+ .timer = &kirkwood_timer, -+ .restart = kirkwood_restart, -+MACHINE_END |