diff options
Diffstat (limited to 'package/uboot-xburst/files/include/configs/sakc.h')
| -rw-r--r-- | package/uboot-xburst/files/include/configs/sakc.h | 200 |
1 files changed, 0 insertions, 200 deletions
diff --git a/package/uboot-xburst/files/include/configs/sakc.h b/package/uboot-xburst/files/include/configs/sakc.h deleted file mode 100644 index b88d8b08bd..0000000000 --- a/package/uboot-xburst/files/include/configs/sakc.h +++ /dev/null @@ -1,200 +0,0 @@ -/* - * Authors: Xiangfu Liu <xiangfu.z@gmail.com> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 3 of the License, or (at your option) any later version. - */ - -/* - * This file contains the configuration parameters for SAKC. - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#define DEBUG -#define CONFIG_MIPS32 1 /* MIPS32 CPU core */ -#define CONFIG_JzRISC 1 /* JzRISC core */ -#define CONFIG_JZSOC 1 /* Jz SoC */ -#define CONFIG_JZ4725 1 /* Jz4725 SoC */ -#define CONFIG_JZ4740 1 /* Jz4740 SoC */ -#define CONFIG_SAKC 1 /* SAKC board */ - -#define MMC_BUS_WIDTH_1BIT 1 /* 1 for MMC 1Bit Bus Width */ - -//#define CONFIG_LCD 1 /* LCD support */ -//#define LCD_BPP LCD_COLOR32 /*5:18,24,32 bits per pixel */ -//#define CONFIG_SYS_WHITE_ON_BLACK 1 - -#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */ -#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */ -#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */ -#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED - -#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */ -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_MMC 1 -#define CONFIG_FAT 1 -#define CONFIG_DOS_PARTITION 1 -#define CONFIG_SKIP_LOWLEVEL_INIT 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_NO_FLASH 1 -#define CONFIG_ENV_OVERWRITE 1 - -#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL) -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTFILE "uImage" /* file to load */ -#define CONFIG_BOOTARGS "mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait" -#define CONFIG_EXTRA_ENV_SETTINGS 1 -#define CONFIG_BOOTARGSFROMSD "mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait" -#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" - -/* - * Command line configuration. - */ -#define CONFIG_CMD_BDI /* bdinfo */ -#define CONFIG_CMD_BOOTD /* bootd */ -#define CONFIG_CMD_CONSOLE /* coninfo */ -#define CONFIG_CMD_ECHO /* echo arguments */ -#define CONFIG_CMD_IMI /* iminfo */ -#define CONFIG_CMD_ITEST /* Integer (and string) test */ - -#define CONFIG_CMD_LOADB /* loadb */ -#define CONFIG_CMD_LOADS /* loads */ -#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */ -#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/ -#define CONFIG_CMD_RUN /* run command in env variable */ -#define CONFIG_CMD_SAVEENV /* saveenv */ -#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ -#define CONFIG_CMD_SOURCE /* "source" command support */ -#define CONFIG_CMD_XIMG /* Load part of Multi Image */ - -#define CONFIG_CMD_NAND -#define CONFIG_CMD_MMC -#define CONFIG_CMD_FAT - -/* - * Serial download configuration - */ -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "SAKC# " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -/* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ - -#define CONFIG_SYS_MALLOC_LEN 128 * 1024 -#define CONFIG_SYS_BOOTPARAMS_LEN 128 * 1024 - -#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */ -#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 -#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */ -#define CONFIG_SYS_MEMTEST_START 0x80100000 -#define CONFIG_SYS_MEMTEST_END 0x80800000 - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ - -/* - * NAND FLASH configuration - */ -/* NAND Boot config code */ -#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3 - -#define SAKC_NAND_SIZE 1 /* if board nand flash is 1GB, set to 1 - * if board nand flash is 2GB, set to 2 - * for change the PAGE_SIZE and BLOCK_SIZE - * will delete when there is no 1GB flash - */ - -#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * SAKC_NAND_SIZE) -/* nand chip block size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * SAKC_NAND_SIZE << 10) -/* nand bad block was marked at this page in a block, start from 0 */ -#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127 -/* ECC offset position in oob area, default value is 6 if it isn't defined */ -#define CONFIG_SYS_NAND_ECC_POS (6 * SAKC_NAND_SIZE) -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xB8000000 -#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/ -#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE - -/* - * IPL (Initial Program Loader, integrated inside CPU) - * Will load first 8k from NAND (SPL) into cache and execute it from there. - * - * SPL (Secondary Program Loader) - * Will load special U-Boot version (NUB) from NAND and execute it. This SPL - * has to fit into 8kByte. It sets up the CPU and configures the SDRAM - * controller and the NAND controller so that the special U-Boot image can be - * loaded from NAND to SDRAM. - * - * NUB (NAND U-Boot) - * This NAND U-Boot (NUB) is a special U-Boot version which can be started - * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. - * - */ -#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */ -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST -/* Start NUB from this addr*/ - -/* - * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) - */ -#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */ -#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ - -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE) -/* environment starts here */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) - -/* in qi_lb60.h/config.mk TEXT_BAS = 0x88000000 */ -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE - -/* - * SDRAM Info. - */ -#define CONFIG_NR_DRAM_BANKS 1 - -/* SDRAM paramters */ -#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */ -#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ -#define SDRAM_ROW 13 /* Row address: 11 to 13 */ -#define SDRAM_COL 9 /* Column address: 8 to 12 */ -#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ - -/* SDRAM Timings, unit: ns */ -#define SDRAM_TRAS 45 /* RAS# Active Time */ -#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ -#define SDRAM_TPC 20 /* RAS# Precharge Time */ -#define SDRAM_TRWL 7 /* Write Latency Time */ -#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */ - -/* - * Cache Configuration - */ -#define CONFIG_SYS_DCACHE_SIZE 16384 -#define CONFIG_SYS_ICACHE_SIZE 16384 -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * GPIO definition - */ -#define GPIO_SD_DETECT (2 * 32 + 27) -#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */ -#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */ - -#endif /* __CONFIG_H */ |