diff options
Diffstat (limited to 'package/uboot-kirkwood/files/board/Marvell/dockstar/dockstar.c')
| -rw-r--r-- | package/uboot-kirkwood/files/board/Marvell/dockstar/dockstar.c | 155 |
1 files changed, 0 insertions, 155 deletions
diff --git a/package/uboot-kirkwood/files/board/Marvell/dockstar/dockstar.c b/package/uboot-kirkwood/files/board/Marvell/dockstar/dockstar.c deleted file mode 100644 index 13cd3474b4..0000000000 --- a/package/uboot-kirkwood/files/board/Marvell/dockstar/dockstar.c +++ /dev/null @@ -1,155 +0,0 @@ -/* - * (C) Copyright 2009 - * Marvell Semiconductor <www.marvell.com> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301 USA - */ - -#include <common.h> -#include <miiphy.h> -#include <asm/arch/kirkwood.h> -#include <asm/arch/mpp.h> -#include "dockstar.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_init(void) -{ - /* - * default gpio configuration - * There are maximum 64 gpios controlled through 2 sets of registers - * the below configuration configures mainly initial LED status - */ - kw_config_gpio(DOCKSTAR_OE_VAL_LOW, - DOCKSTAR_OE_VAL_HIGH, - DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH); - - /* Multi-Purpose Pins Functionality configuration */ - u32 kwmpp_config[] = { - MPP0_NF_IO2, - MPP1_NF_IO3, - MPP2_NF_IO4, - MPP3_NF_IO5, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP6_SYSRST_OUTn, - MPP7_GPO, - MPP8_UART0_RTS, - MPP9_UART0_CTS, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP12_SD_CLK, - MPP13_SD_CMD, - MPP14_SD_D0, - MPP15_SD_D1, - MPP16_SD_D2, - MPP17_SD_D3, - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP20_GPIO, - MPP21_GPIO, - MPP22_GPIO, - MPP23_GPIO, - MPP24_GPIO, - MPP25_GPIO, - MPP26_GPIO, - MPP27_GPIO, - MPP28_GPIO, - MPP29_TSMP9, - MPP30_GPIO, - MPP31_GPIO, - MPP32_GPIO, - MPP33_GPIO, - MPP34_GPIO, - MPP35_GPIO, - MPP36_GPIO, - MPP37_GPIO, - MPP38_GPIO, - MPP39_GPIO, - MPP40_GPIO, - MPP41_GPIO, - MPP42_GPIO, - MPP43_GPIO, - MPP44_GPIO, - MPP45_GPIO, - MPP46_GPIO, - MPP47_GPIO, - MPP48_GPIO, - MPP49_GPIO, - 0 - }; - kirkwood_mpp_conf(kwmpp_config); - - /* - * arch number of board - */ - gd->bd->bi_arch_number = MACH_TYPE_DOCKSTAR; - - /* adress of boot parameters */ - gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; - - return 0; -} - -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - -#ifdef CONFIG_RESET_PHY_R -/* Configure and enable MV88E1116 PHY */ -void reset_phy(void) -{ - u16 reg; - u16 devadr; - char *name = "egiga0"; - - if (miiphy_set_current_dev(name)) - return; - - /* command to read PHY dev address */ - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { - printf("Err..%s could not read PHY dev address\n", - __FUNCTION__); - return; - } - - /* - * Enable RGMII delay on Tx and Rx for CPU port - * Ref: sec 4.7.2 of chip datasheet - */ - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); - - /* reset the phy */ - miiphy_reset(name, devadr); - - printf("88E1116 Initialized on %s\n", name); -} -#endif /* CONFIG_RESET_PHY_R */ |