diff options
Diffstat (limited to 'package/kismet/files/kismet.conf')
| -rw-r--r-- | package/kismet/files/kismet.conf | 281 |
1 files changed, 0 insertions, 281 deletions
diff --git a/package/kismet/files/kismet.conf b/package/kismet/files/kismet.conf deleted file mode 100644 index a417d2885b..0000000000 --- a/package/kismet/files/kismet.conf +++ /dev/null @@ -1,281 +0,0 @@ -# Kismet config file -# Most of the "static" configs have been moved to here -- the command line -# config was getting way too crowded and cryptic. We want functionality, -# not continually reading --help! - -# Version of Kismet config -version=2005.01.R1 - -# Name of server (Purely for organiational purposes) -servername=Kismet - -# User to setid to (should be your normal user) -suiduser=nobody - -# Sources are defined as: -# source=cardtype,interface,name[,initialchannel] -# Card types and required drivers are listed in the README. -# The initial channel is optional, if hopping is not enabled it can be used -# to set the channel the interface listens on. -# YOU MUST CHANGE THIS TO BE THE SOURCE YOU WANT TO USE -source=wrt54g,eth1,wireless -# For v1 hardware uncomment this: -# source=wrt54g,eth2,wireless - -# Comma-separated list of sources to enable. This is only needed if you defined -# multiple sources and only want to enable some of them. By default, all defined -# sources are enabled. -# For example: -# enablesources=prismsource,ciscosource - -# Do we channelhop? -channelhop=true - -# How many channels per second do we hop? (1-10) -channelvelocity=5 - -# By setting the dwell time for channel hopping we override the channelvelocity -# setting above and dwell on each channel for the given number of seconds. -#channeldwell=10 - -# Do we split channels between cards on the same spectrum? This means if -# multiple 802.11b capture sources are defined, they will be offset to cover -# the most possible spectrum at a given time. This also controls splitting -# fine-tuned sourcechannels lines which cover multiple interfaces (see below) -channelsplit=true - -# Basic channel hopping control: -# These define the channels the cards hop through for various frequency ranges -# supported by Kismet. More finegrain control is available via the -# "sourcechannels" configuration option. -# -# Don't change the IEEE80211<x> identifiers or channel hopping won't work. - -# Users outside the US might want to use this list: -# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12 -defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10 - -# 802.11g uses the same channels as 802.11b... -defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10 - -# 802.11a channels are non-overlapping so sequential is fine. You may want to -# adjust the list depending on the channels your card actually supports. -# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216 -defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64 - -# Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you -# can also explicitly override a given source. You can use the script -# extras/listchan.pl to extract all the channels your card supports. -defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64 - -# Fine-tuning channel hopping control: -# The sourcechannels option can be used to set the channel hopping for -# specific interfaces, and to control what interfaces share a list of -# channels for split hopping. This can also be used to easily lock -# one card on a single channel while hopping with other cards. -# Any card without a sourcechannel definition will use the standard hopping -# list. -# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN - -# ie, for us channels on the source 'prism2source' (same as normal channel -# hopping behavior): -# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10 - -# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay -# on channel 6 and prism2b to hop normally. By not setting a sourcechannels -# line for prism2b, it will use the standard hopping. -# sourcechannels=prism2a:6 - -# To assign the same custom hop channel to multiple sources, or to split the -# same custom hop channel over two sources (if splitchannels is true), list -# them all on the same sourcechannels line: -# sourcechannels=prism2a,prism2b,prism2c:1,6,11 - -# Port to serve GUI data -tcpport=2501 -# People allowed to connect, comma seperated IP addresses or network/mask -# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as -# numbers (/24) -allowedhosts=127.0.0.1 -# Maximum number of concurrent GUI's -maxclients=5 - -# Do we have a GPS? -gps=false -# Host:port that GPSD is running on. This can be localhost OR remote! -gpshost=localhost:2947 -# Do we lock the mode? This overrides coordinates of lock "0", which will -# generate some bad information until you get a GPS lock, but it will -# fix problems with GPS units with broken NMEA that report lock 0 -gpsmodelock=false - -# Packet filtering options: -# filter_tracker - Packets filtered from the tracker are not processed or -# recorded in any way. -# filter_dump - Packets filtered at the dump level are tracked, displayed, -# and written to the csv/xml/network/etc files, but not -# recorded in the packet dump -# filter_export - Controls what packets influence the exported CSV, network, -# xml, gps, etc files. -# All filtering options take arguments containing the type of address and -# addresses to be filtered. Valid address types are 'ANY', 'BSSID', -# 'SOURCE', and 'DEST'. Filtering can be inverted by the use of '!' before -# the address. For example, -# filter_tracker=ANY(!00:00:DE:AD:BE:EF) -# has the same effect as the previous mac_filter config file option. -# filter_tracker=... -# filter_dump=... -# filter_export=... - -# Alerts to be reported and the throttling rates. -# alert=name,throttle/unit,burst -# The throttle/unit describes the number of alerts of this type that are -# sent per time unit. Valid time units are second, minute, hour, and day. -# Burst describes the number of alerts sent before throttling takes place. -# For example: -# alert=FOO,10/min,5 -# Would allow 5 alerts through before throttling is enabled, and will then -# limit the number of alerts to 10 per minute. -# A throttle rate of 0 disables throttling of the alert. -# See the README for a list of alert types. -alert=NETSTUMBLER,5/min,2 -alert=WELLENREITER,5/min,2 -alert=LUCENTTEST,5/min,2 -alert=DEAUTHFLOOD,5/min,4 -alert=BCASTDISCON,5/min,4 -alert=CHANCHANGE,5/min,4 -alert=AIRJACKSSID,5/min,2 -alert=PROBENOJOIN,5/min,2 -alert=DISASSOCTRAFFIC,5/min,2 -alert=NULLPROBERESP,5/min,5 -alert=BSSTIMESTAMP,5/min,5 - -# Known WEP keys to decrypt, bssid,hexkey. This is only for networks where -# the keys are already known, and it may impact throughput on slower hardware. -# Multiple wepkey lines may be used for multiple BSSIDs. -# wepkey=00:DE:AD:C0:DE:00,FEEDFACEDEADBEEF01020304050607080900 - -# Is transmission of the keys to the client allowed? This may be a security -# risk for some. If you disable this, you will not be able to query keys from -# a client. -allowkeytransmit=true - -# How often (in seconds) do we write all our data files (0 to disable) -writeinterval=300 - -# Where do we get our manufacturer fingerprints from? Assumed to be in the -# default config directory if an absolute path is not given. -ap_manuf=ap_manuf -client_manuf=client_manuf - -# Use metric measurements in the output? -metric=false - -# Do we write waypoints for gpsdrive to load? Note: This is NOT related to -# recent versions of GPSDrive's native support of Kismet. -waypoints=false -# GPSMap waypoint file. This WILL be truncated. -waypointdata=%h/.gpsdrive/way_kismet.txt - -# How many alerts do we backlog for new clients? Only change this if you have -# a -very- low memory system and need those extra bytes, or if you have a high -# memory system and a huge number of alert conditions. -alertbacklog=50 - -# File types to log, comma seperated -# dump - raw packet dump -# network - plaintext detected networks -# csv - plaintext detected networks in CSV format -# xml - XML formatted network and cisco log -# weak - weak packets (in airsnort format) -# cisco - cisco equipment CDP broadcasts -# gps - gps coordinates -logtypes=dump,network,csv,xml,weak,cisco,gps - -# Do we track probe responses and merge probe networks into their owners? -# This isn't always desireable, depending on the type of monitoring you're -# trying to do. -trackprobenets=true - -# Do we log "noise" packets that we can't decipher? I tend to not, since -# they don't have anything interesting at all in them. -noiselog=false - -# Do we log corrupt packets? Corrupt packets have enough header information -# to see what they are, but someting is wrong with them that prevents us from -# completely dissecting them. Logging these is usually not a bad idea. -corruptlog=true - -# Do we log beacon packets or do we filter them out of the dumpfile -beaconlog=true - -# Do we log PHY layer packets or do we filter them out of the dumpfile -phylog=true - -# Do we mangle packets if we can decrypt them or if they're fuzzy-detected -mangledatalog=true - -# Do we do "fuzzy" crypt detection? (byte-based detection instead of 802.11 -# frame headers) -# valid option: Comma seperated list of card types to perform fuzzy detection -# on, or 'all' -fuzzycrypt=wtapfile,wlanng,wlanng_legacy,wlanng_avs,hostap,wlanng_wext - -# What type of dump do we generate? -# valid option: "wiretap" -dumptype=wiretap -# Do we limit the size of dump logs? Sometimes ethereal can't handle big ones. -# 0 = No limit -# Anything else = Max number of packets to log to a single file before closing -# and opening a new one. -dumplimit=0 - -# Do we write data packets to a FIFO for an external data-IDS (such as Snort)? -# See the docs before enabling this. -#fifo=/tmp/kismet_dump - -# Default log title -logdefault=Kismet - -# logtemplate - Filename logging template. -# This is, at first glance, really nasty and ugly, but you'll hardly ever -# have to touch it so don't complain too much. -# -# %n is replaced by the logging instance name -# %d is replaced by the current date as Mon-DD-YYYY -# %D is replaced by the current date as YYYYMMDD -# %t is replaced by the starting log time -# %i is replaced by the increment log in the case of multiple logs -# %l is replaced by the log type (dump, status, crypt, etc) -# %h is replaced by the home directory -# ie, "netlogs/%n-%d-%i.dump" called with a logging name of "Pok" could expand -# to something like "netlogs/Pok-Dec-20-01-1.dump" for the first instance and -# "netlogs/Pok-Dec-20-01-2.%l" for the second logfile generated. -# %h/netlots/%n-%d-%i.dump could expand to -# /home/foo/netlogs/Pok-Dec-20-01-2.dump -# -# Other possibilities: Sorting by directory -# logtemplate=%l/%n-%d-%i -# Would expand to, for example, -# dump/Pok-Dec-20-01-1 -# crypt/Pok-Dec-20-01-1 -# and so on. The "dump", "crypt", etc, dirs must exist before kismet is run -# in this case. -logtemplate=%n-%d-%i.%l - -# Where do we store the pid file of the server? -piddir=/var/run/ - -# Where state info, etc, is stored. You shouldnt ever need to change this. -# This is a directory. -configdir=%h/.kismet/ - -# cloaked SSID file. You shouldn't ever need to change this. -ssidmap=ssid_map - -# Group map file. You shouldn't ever need to change this. -groupmap=group_map - -# IP range map file. You shouldn't ever need to change this. -ipmap=ip_map - |