diff options
Diffstat (limited to 'openwrt/package/kismet/files/kismet_drone.conf')
| -rw-r--r-- | openwrt/package/kismet/files/kismet_drone.conf | 120 |
1 files changed, 120 insertions, 0 deletions
diff --git a/openwrt/package/kismet/files/kismet_drone.conf b/openwrt/package/kismet/files/kismet_drone.conf new file mode 100644 index 0000000000..865278ab7a --- /dev/null +++ b/openwrt/package/kismet/files/kismet_drone.conf @@ -0,0 +1,120 @@ +# Kismet drone config file + +version=Feb.04.01a + +# Name of server (Purely for organiational purposes) +servername=Kismet + +# User to setid to (should be your normal user) +suiduser=your_user_here + +# Port to serve packet data... This probably shouldn't be the same as the port +# you configured kismet_server for, or else you'll have problems running them +# on the same system. +tcpport=3501 +# People allowed to connect, comma seperated IP addresses or network/mask +# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as +# numbers (/24) +allowedhosts=127.0.0.1 +# Maximum number of concurrent stream attachments +maxclients=5 + +# Packet sources: +# source=capture_cardtype,capture_interface,capture_name +# Card type - Specifies the type of device. It can be one of: +# cisco - Cisco card with Linux Kernel drivers +# cisco_cvs - Cisco card with CVS Linux drivers +# cisco_bsd - Cisco on *BSD +# prism2 - Prism2 using wlan-ng drivers with pcap support (all +# current versions support pcap) +# prism2_hostap - Prism2 using hostap drivers +# prism2_legacy - Prism2 using wlan-ng drivers without pcap support (0.1.9) +# prism2_bsd - Prism2 on *BSD +# orinoco - Orinoco cards using Snax's patched driers +# generic - Generic card with no specific support. You will have +# to put this into monitor mode yourself! +# wsp100 - WSP100 embedded remote sensor. +# wtapfile - Saved file of packets readable by libwiretap +# ar5k - ar5k 802.11a using the vt_ar5k drivers +# Capture interface - Specifies the network interface Kismet will watch for +# packets to come in on. Typically "ethX" or "wlanX". For the WSP100 capture +# engine, the WSP100 device sends packets via a UDP stream, so the capture +# interface should be in the form of host:port where 'host' is the WSP100 and +# 'port' is the local UDP port that it will send data to. +# Capture Name - The name Kismet uses for this capture source. This is the +# name used to specify what sources to enable. +# +# To enable multiple sources, specify a source line for each and then use the +# enablesources line to enable them. For example: +# source=prism2,wlan0,prism +# source=cisco,eth0,cisco + +source=generic,prism0,Kismet-Drone + +# Comma-separated list of sources to enable. This is only needed if you wish +# to selectively enable multiple sources. +# enablesources=prism,cisco + +# Do we channelhop? +channelhop=true + +# How many channels per second do we hop? (1-10) +channelvelocity=5 + +# By setting the dwell time for channel hopping we override the channelvelocity +# setting above and dwell on each channel for the given number of seconds. +#channeldwell=10 + +# Do we split channels between cards on the same spectrum? This means if +# multiple 802.11b capture sources are defined, they will be offset to cover +# the most possible spectrum at a given time. This also controls splitting +# fine-tuned sourcechannels lines which cover multiple interfaces (see below) +splitchannels=true + +# Basic channel hopping control: +# These define the channels the cards hop through for various frequency ranges +# supported by Kismet. More finegrain control is available via the +# "sourcechannels" configuration option. +# +# Don't change the IEEE80211<x> identifiers or channel hopping won't work. + +# Users outside the US might want to use this list: +# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12 +defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10 + +# 802.11g uses the same channels as 802.11b... +defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10 + +# 802.11a channels are non-overlapping so sequential is fine. You may want to +# adjust the list depending on the channels your card actually supports. +# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216 +defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64 + +# Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you +# can also explicitly override a given source. You can use the script +# extras/listchan.pl to extract all the channels your card supports. +defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64 + +# Fine-tuning channel hopping control: +# The sourcechannels option can be used to set the channel hopping for +# specific interfaces, and to control what interfaces share a list of +# channels for split hopping. This can also be used to easily lock +# one card on a single channel while hopping with other cards. +# Any card without a sourcechannel definition will use the standard hopping +# list. +# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN + +# ie, for us channels on the source 'prism2source' (same as normal channel +# hopping behavior): +# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10 + +# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay +# on channel 6 and prism2b to hop normally. By not setting a sourcechannels +# line for prism2b, it will use the standard hopping. +# sourcechannels=prism2a:6 + +# To assign the same custom hop channel to multiple sources, or to split the +# same custom hop channel over two sources (if splitchannels is true), list +# them all on the same sourcechannels line: +# sourcechannels=prism2a,prism2b,prism2c:1,6,11 + |