diff options
23 files changed, 2057 insertions, 0 deletions
diff --git a/target/linux/adm5120/patches-2.6.25/001-adm5120.patch b/target/linux/adm5120/patches-2.6.25/001-adm5120.patch new file mode 100644 index 0000000000..5fe25a562d --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/001-adm5120.patch @@ -0,0 +1,117 @@ +Index: linux-2.6.25/arch/mips/Kconfig +=================================================================== +--- linux-2.6.25.orig/arch/mips/Kconfig ++++ linux-2.6.25/arch/mips/Kconfig +@@ -18,6 +18,20 @@ choice + prompt "System type" + default SGI_IP22 + ++config MIPS_ADM5120 ++ bool "ADM5120 SoC based machines" ++ select CEVT_R4K ++ select CSRC_R4K ++ select SYS_HAS_CPU_MIPS32_R1 ++ select SYS_HAS_EARLY_PRINTK ++ select DMA_NONCOHERENT ++ select HW_HAS_PCI ++ select IRQ_CPU ++ select SYS_SUPPORTS_LITTLE_ENDIAN ++ select SYS_SUPPORTS_BIG_ENDIAN ++ select SYS_SUPPORTS_32BIT_KERNEL ++ select GENERIC_GPIO ++ + config MACH_ALCHEMY + bool "Alchemy processor based machines" + +@@ -683,6 +697,7 @@ config WR_PPMC + + endchoice + ++source "arch/mips/adm5120/Kconfig" + source "arch/mips/au1000/Kconfig" + source "arch/mips/basler/excite/Kconfig" + source "arch/mips/jazz/Kconfig" +Index: linux-2.6.25/arch/mips/Makefile +=================================================================== +--- linux-2.6.25.orig/arch/mips/Makefile ++++ linux-2.6.25/arch/mips/Makefile +@@ -174,6 +174,16 @@ cflags-$(CONFIG_MACH_JAZZ) += -Iinclude/ + load-$(CONFIG_MACH_JAZZ) += 0xffffffff80080000 + + # ++# ADMtek 5120 ++# ++ ++libs-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/prom/ ++core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/ ++core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/boards/ ++cflags-$(CONFIG_MIPS_ADM5120) += -Iinclude/asm-mips/mach-adm5120 ++load-$(CONFIG_MIPS_ADM5120) += 0xffffffff80001000 ++ ++# + # Common Alchemy Au1x00 stuff + # + core-$(CONFIG_SOC_AU1X00) += arch/mips/au1000/common/ +Index: linux-2.6.25/include/asm-mips/bootinfo.h +=================================================================== +--- linux-2.6.25.orig/include/asm-mips/bootinfo.h ++++ linux-2.6.25/include/asm-mips/bootinfo.h +@@ -94,6 +94,58 @@ + #define MACH_MSP7120_FPGA 5 /* PMC-Sierra MSP7120 Emulation */ + #define MACH_MSP_OTHER 255 /* PMC-Sierra unknown board type */ + ++/* ++ * Valid machtype for group ADMtek ADM5120 ++ */ ++#define MACH_ADM5120_GENERIC 0 /* Generic board */ ++#define MACH_ADM5120_WP54G_WRT 1 /* Compex WP54G-WRT */ ++#define MACH_ADM5120_WP54G 2 /* Compex WP54G */ ++#define MACH_ADM5120_WP54AG 3 /* Compex WP54AG */ ++#define MACH_ADM5120_WPP54G 4 /* Compex WPP54G */ ++#define MACH_ADM5120_WPP54AG 5 /* Compex WPP54AG */ ++#define MACH_ADM5120_NP28G 6 /* Compex NP28G */ ++#define MACH_ADM5120_NP28GHS 7 /* Compex NP28G HotSpot */ ++#define MACH_ADM5120_NP27G 8 /* Compex NP27G */ ++#define MACH_ADM5120_WP54Gv1C 9 /* Compex WP54G version 1C */ ++#define MACH_ADM5120_RB_111 10 /* Mikrotik RouterBOARD 111 */ ++#define MACH_ADM5120_RB_112 11 /* Mikrotik RouterBOARD 112 */ ++#define MACH_ADM5120_RB_133 12 /* Mikrotik RouterBOARD 133 */ ++#define MACH_ADM5120_RB_133C 13 /* Mikrotik RouterBOARD 133c */ ++#define MACH_ADM5120_RB_150 14 /* Mikrotik RouterBOARD 150 */ ++#define MACH_ADM5120_RB_153 15 /* Mikrotik RouterBOARD 153 */ ++#define MACH_ADM5120_HS100 16 /* ZyXEL HomeSafe 100/100W */ ++#define MACH_ADM5120_P334 17 /* ZyXEL Prestige 334 */ ++#define MACH_ADM5120_P334U 18 /* ZyXEL Prestige 334U */ ++#define MACH_ADM5120_P334W 19 /* ZyXEL Prestige 334W */ ++#define MACH_ADM5120_P334WH 20 /* ZyXEL Prestige 334WH */ ++#define MACH_ADM5120_P334WHD 21 /* ZyXEL Prestige 334WHD */ ++#define MACH_ADM5120_P334WT 22 /* ZyXEL Prestige 334WT */ ++#define MACH_ADM5120_P335 23 /* ZyXEL Prestige 335/335WT */ ++#define MACH_ADM5120_P335PLUS 24 /* ZyXEL Prestige 335Plus */ ++#define MACH_ADM5120_P335U 25 /* ZyXEL Prestige 335U */ ++#define MACH_ADM5120_ES2108 26 /* ZyXEL Ethernet Switch 2108 */ ++#define MACH_ADM5120_ES2108F 27 /* ZyXEL Ethernet Switch 2108-F */ ++#define MACH_ADM5120_ES2108G 28 /* ZyXEL Ethernet Switch 2108-G */ ++#define MACH_ADM5120_ES2108LC 29 /* ZyXEL Ethernet Switch 2108-LC */ ++#define MACH_ADM5120_ES2108PWR 30 /* ZyXEL Ethernet Switch 2108-PWR */ ++#define MACH_ADM5120_ES2024A 31 /* ZyXEL Ethernet Switch 2024A */ ++#define MACH_ADM5120_ES2024PWR 32 /* ZyXEL Ethernet Switch 2024PWR */ ++#define MACH_ADM5120_CAS630 33 /* Cellvision CAS-630/630W */ ++#define MACH_ADM5120_CAS670 34 /* Cellvision CAS-670/670W */ ++#define MACH_ADM5120_CAS700 36 /* Cellvision CAS-700/700W */ ++#define MACH_ADM5120_CAS771 37 /* Cellvision CAS-771/771W */ ++#define MACH_ADM5120_CAS790 38 /* Cellvision CAS-790 */ ++#define MACH_ADM5120_CAS861 39 /* Cellvision CAS-861/861W */ ++#define MACH_ADM5120_NFS101U 40 /* Cellvision NFS-101U/101WU */ ++#define MACH_ADM5120_NFS202U 41 /* Cellvision NFS-202U/202WU */ ++#define MACH_ADM5120_EASY5120PATA 42 /* Infineon EASY 5120P-ATA */ ++#define MACH_ADM5120_EASY5120RT 43 /* Infineon EASY 5120-RT */ ++#define MACH_ADM5120_EASY5120WVOIP 44 /* Infineon EASY 5120-WVoIP */ ++#define MACH_ADM5120_EASY83000 45 /* Infineon EASY-83000 */ ++#define MACH_ADM5120_BR6104K 46 /* Edimax BR-6104K/BR-6104KP */ ++#define MACH_ADM5120_RB_192 47 /* Mikrotik RouterBOARD 192 */ ++#define MACH_ADM5120_BR61x4WG 48 /* Edimax BR-6104Wg/BR-6114WG */ ++ + #define CL_SIZE COMMAND_LINE_SIZE + + extern char *system_type; diff --git a/target/linux/adm5120/patches-2.6.25/002-adm5120_flash.patch b/target/linux/adm5120/patches-2.6.25/002-adm5120_flash.patch new file mode 100644 index 0000000000..f23ebaac2c --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/002-adm5120_flash.patch @@ -0,0 +1,26 @@ +Index: linux-2.6.25/drivers/mtd/maps/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/maps/Kconfig ++++ linux-2.6.25/drivers/mtd/maps/Kconfig +@@ -590,5 +590,9 @@ config MTD_PLATRAM + + This selection automatically selects the map_ram driver. + ++config MTD_ADM5120 ++ tristate "Map driver for ADM5120 based boards" ++ depends on MIPS_ADM5120 ++ + endmenu + +Index: linux-2.6.25/drivers/mtd/maps/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/maps/Makefile ++++ linux-2.6.25/drivers/mtd/maps/Makefile +@@ -44,6 +44,7 @@ obj-$(CONFIG_MTD_DBOX2) += dbox2-flash. + obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o + obj-$(CONFIG_MTD_PCI) += pci.o + obj-$(CONFIG_MTD_ALCHEMY) += alchemy-flash.o ++obj-$(CONFIG_MTD_ADM5120) += adm5120-flash.o + obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o + obj-$(CONFIG_MTD_EDB7312) += edb7312.o + obj-$(CONFIG_MTD_IMPA7) += impa7.o diff --git a/target/linux/adm5120/patches-2.6.25/003-adm5120_switch.patch b/target/linux/adm5120/patches-2.6.25/003-adm5120_switch.patch new file mode 100644 index 0000000000..69a0182203 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/003-adm5120_switch.patch @@ -0,0 +1,27 @@ +Index: linux-2.6.25/drivers/net/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/net/Kconfig ++++ linux-2.6.25/drivers/net/Kconfig +@@ -606,6 +606,10 @@ config MIPS_AU1X00_ENET + If you have an Alchemy Semi AU1X00 based system + say Y. Otherwise, say N. + ++config MIPS_ADM5120_ENET ++ tristate "MIPS ADM5120 Ethernet switch support" ++ depends on MIPS_ADM5120 ++ + config SGI_IOC3_ETH + bool "SGI IOC3 Ethernet" + depends on PCI && SGI_IP27 +Index: linux-2.6.25/drivers/net/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/net/Makefile ++++ linux-2.6.25/drivers/net/Makefile +@@ -187,6 +187,7 @@ obj-$(CONFIG_SC92031) += sc92031.o + # This is also a 82596 and should probably be merged + obj-$(CONFIG_LP486E) += lp486e.o + ++obj-$(CONFIG_MIPS_ADM5120_ENET) += adm5120sw.o + obj-$(CONFIG_ETH16I) += eth16i.o + obj-$(CONFIG_ZORRO8390) += zorro8390.o + obj-$(CONFIG_HPLANCE) += hplance.o 7990.o diff --git a/target/linux/adm5120/patches-2.6.25/005-adm5120_usb.patch b/target/linux/adm5120/patches-2.6.25/005-adm5120_usb.patch new file mode 100644 index 0000000000..5775578ede --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/005-adm5120_usb.patch @@ -0,0 +1,35 @@ +Index: linux-2.6.25/drivers/usb/host/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/usb/host/Kconfig ++++ linux-2.6.25/drivers/usb/host/Kconfig +@@ -260,3 +260,6 @@ config USB_R8A66597_HCD + To compile this driver as a module, choose M here: the + module will be called r8a66597-hcd. + ++config USB_ADM5120_HCD ++ tristate "ADM5120 HCD support (EXPERIMENTAL)" ++ depends on USB && MIPS_ADM5120 && EXPERIMENTAL +Index: linux-2.6.25/drivers/usb/host/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/usb/host/Makefile ++++ linux-2.6.25/drivers/usb/host/Makefile +@@ -8,6 +8,7 @@ endif + + obj-$(CONFIG_PCI) += pci-quirks.o + ++obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o + obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o + obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o + obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o +Index: linux-2.6.25/drivers/usb/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/usb/Makefile ++++ linux-2.6.25/drivers/usb/Makefile +@@ -16,6 +16,7 @@ obj-$(CONFIG_USB_UHCI_HCD) += host/ + obj-$(CONFIG_USB_SL811_HCD) += host/ + obj-$(CONFIG_USB_U132_HCD) += host/ + obj-$(CONFIG_USB_R8A66597_HCD) += host/ ++obj-$(CONFIG_USB_ADM5120_HCD) += host/ + + obj-$(CONFIG_USB_ACM) += class/ + obj-$(CONFIG_USB_PRINTER) += class/ diff --git a/target/linux/adm5120/patches-2.6.25/006-adm5120_leds.patch b/target/linux/adm5120/patches-2.6.25/006-adm5120_leds.patch new file mode 100644 index 0000000000..474e7cabd1 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/006-adm5120_leds.patch @@ -0,0 +1,38 @@ +Index: linux-2.6.25/drivers/leds/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/leds/Kconfig ++++ linux-2.6.25/drivers/leds/Kconfig +@@ -25,6 +25,21 @@ config LEDS_ATMEL_PWM + This option enables support for LEDs driven using outputs + of the dedicated PWM controller found on newer Atmel SOCs. + ++config LEDS_ADM5120 ++ tristate "LED Support for ADM5120 GPIO LEDs" ++ depends on LEDS_GPIO && MIPS_ADM5120 ++ help ++ This option enables support for LEDs connected to GPIO lines ++ on ADM5120 SoC based platforms. ++ ++config LEDS_ADM5120_EXPERIMENTAL ++ bool "Enable ADM5120 LEDs experimental code" ++ depends on LEDS_ADM5120 ++ ++config LEDS_ADM5120_DIAG ++ bool "Enable ADM5120 LEDs diagnostic mode" ++ depends on LEDS_ADM5120 ++ + config LEDS_CORGI + tristate "LED Support for the Sharp SL-C7x0 series" + depends on LEDS_CLASS && PXA_SHARP_C7xx +Index: linux-2.6.25/drivers/leds/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/leds/Makefile ++++ linux-2.6.25/drivers/leds/Makefile +@@ -5,6 +5,7 @@ obj-$(CONFIG_LEDS_CLASS) += led-class.o + obj-$(CONFIG_LEDS_TRIGGERS) += led-triggers.o + + # LED Platform Drivers ++obj-$(CONFIG_LEDS_ADM5120) += leds-adm5120.o + obj-$(CONFIG_LEDS_ATMEL_PWM) += leds-atmel-pwm.o + obj-$(CONFIG_LEDS_CORGI) += leds-corgi.o + obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o diff --git a/target/linux/adm5120/patches-2.6.25/007-adm5120_pci.patch b/target/linux/adm5120/patches-2.6.25/007-adm5120_pci.patch new file mode 100644 index 0000000000..2da99bacb9 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/007-adm5120_pci.patch @@ -0,0 +1,23 @@ +Index: linux-2.6.25/arch/mips/pci/Makefile +=================================================================== +--- linux-2.6.25.orig/arch/mips/pci/Makefile ++++ linux-2.6.25/arch/mips/pci/Makefile +@@ -48,3 +48,4 @@ obj-$(CONFIG_TOSHIBA_RBTX4938) += fixup- + obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o + obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o + obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o ++obj-$(CONFIG_PCI_ADM5120) += pci-adm5120.o +Index: linux-2.6.25/include/linux/pci_ids.h +=================================================================== +--- linux-2.6.25.orig/include/linux/pci_ids.h ++++ linux-2.6.25/include/linux/pci_ids.h +@@ -1704,6 +1704,9 @@ + #define PCI_VENDOR_ID_ESDGMBH 0x12fe + #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111 + ++#define PCI_VENDOR_ID_ADMTEK 0x1317 ++#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120 ++ + #define PCI_VENDOR_ID_SIIG 0x131f + #define PCI_SUBVENDOR_ID_SIIG 0x131f + #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000 diff --git a/target/linux/adm5120/patches-2.6.25/009-adm5120_leds_switch_trigger.patch b/target/linux/adm5120/patches-2.6.25/009-adm5120_leds_switch_trigger.patch new file mode 100644 index 0000000000..015f8945a1 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/009-adm5120_leds_switch_trigger.patch @@ -0,0 +1,26 @@ +Index: linux-2.6.25/drivers/leds/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/leds/Kconfig ++++ linux-2.6.25/drivers/leds/Kconfig +@@ -213,4 +213,12 @@ config LEDS_TRIGGER_DEFAULT_ON + This allows LEDs to be initialised in the ON state. + If unsure, say Y. + ++config LEDS_TRIGGER_ADM5120_SWITCH ++ tristate "LED ADM5120 Switch Port Status Trigger" ++ depends on LEDS_TRIGGERS && LEDS_ADM5120 ++ help ++ This allows LEDs to be controlled by the port states of ++ the ADM5120 built-in Ethernet Switch ++ If unsure, say N. ++ + endif # NEW_LEDS +Index: linux-2.6.25/drivers/leds/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/leds/Makefile ++++ linux-2.6.25/drivers/leds/Makefile +@@ -30,3 +30,4 @@ obj-$(CONFIG_LEDS_TRIGGER_IDE_DISK) += l + obj-$(CONFIG_LEDS_TRIGGER_HEARTBEAT) += ledtrig-heartbeat.o + obj-$(CONFIG_LEDS_TRIGGER_MORSE) += ledtrig-morse.o + obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON) += ledtrig-default-on.o ++obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o diff --git a/target/linux/adm5120/patches-2.6.25/100-mtd_myloder_partition_parser.patch b/target/linux/adm5120/patches-2.6.25/100-mtd_myloder_partition_parser.patch new file mode 100644 index 0000000000..7239d2307d --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/100-mtd_myloder_partition_parser.patch @@ -0,0 +1,39 @@ +Index: linux-2.6.25/drivers/mtd/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/Kconfig ++++ linux-2.6.25/drivers/mtd/Kconfig +@@ -168,6 +168,22 @@ config MTD_OF_PARTS + the partition map from the children of the flash node, + as described in Documentation/powerpc/booting-without-of.txt. + ++config MTD_MYLOADER_PARTS ++ tristate "MyLoader partition parsing" ++ depends on MIPS_ADM5120 && MTD_PARTITIONS ++ ---help--- ++ MyLoader is a bootloader which allows the user to define partitions ++ in flash devices, by putting a table in the second erase block ++ on the device, similar to a partition table. This table gives the ++ offsets and lengths of the user defined partitions. ++ ++ If you need code which can detect and parse these tables, and ++ register MTD 'partitions' corresponding to each image detected, ++ enable this option. ++ ++ You will still need the parsing functions to be called by the driver ++ for your particular device. It won't happen automatically. ++ + comment "User Modules And Translation Layers" + + config MTD_CHAR +Index: linux-2.6.25/drivers/mtd/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/Makefile ++++ linux-2.6.25/drivers/mtd/Makefile +@@ -12,6 +12,7 @@ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redbo + obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o + obj-$(CONFIG_MTD_AFS_PARTS) += afs.o + obj-$(CONFIG_MTD_OF_PARTS) += ofpart.o ++obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o + + # 'Users' - code which presents functionality to userspace. + obj-$(CONFIG_MTD_CHAR) += mtdchar.o diff --git a/target/linux/adm5120/patches-2.6.25/101-cfi_fixup_macronix_bootloc.patch b/target/linux/adm5120/patches-2.6.25/101-cfi_fixup_macronix_bootloc.patch new file mode 100644 index 0000000000..a1dce2580d --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/101-cfi_fixup_macronix_bootloc.patch @@ -0,0 +1,95 @@ +Index: linux-2.6.25/drivers/mtd/chips/cfi_cmdset_0002.c +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/chips/cfi_cmdset_0002.c ++++ linux-2.6.25/drivers/mtd/chips/cfi_cmdset_0002.c +@@ -47,12 +47,19 @@ + #define MANUFACTURER_AMD 0x0001 + #define MANUFACTURER_ATMEL 0x001F + #define MANUFACTURER_SST 0x00BF ++#define MANUFACTURER_MACRONIX 0x00C2 + #define SST49LF004B 0x0060 + #define SST49LF040B 0x0050 + #define SST49LF008A 0x005a + #define AT49BV6416 0x00d6 + #define MANUFACTURER_SAMSUNG 0x00ec + ++/* Macronix */ ++#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */ ++#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */ ++#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */ ++#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */ ++ + static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *); + static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); + static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); +@@ -221,6 +228,41 @@ static void fixup_use_atmel_lock(struct + mtd->flags |= MTD_POWERUP_LOCK; + } + ++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC ++/* ++ * Some Macronix chips has no/bad bootblock information in the CFI table ++ */ ++static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param) ++{ ++ struct map_info *map = mtd->priv; ++ struct cfi_private *cfi = map->fldrv_priv; ++ struct cfi_pri_amdstd *extp = cfi->cmdset_priv; ++ __u8 t; ++ ++ switch (cfi->id) { ++ /* TODO: put affected chip ids here */ ++ case MX29LV160B: ++ case MX29LV320B: ++ t = 2; /* Bottom boot */ ++ break; ++ case MX29LV160T: ++ case MX29LV320T: ++ t = 3; /* Top boot */ ++ break; ++ default: ++ return; ++ } ++ ++ if (extp->TopBottom == t) ++ /* boot location detected by the CFI layer is correct */ ++ return; ++ ++ extp->TopBottom = t; ++ printk("%s: Macronix chip detected, id:0x%04X, boot location forced " ++ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top"); ++} ++#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */ ++ + static struct cfi_fixup cfi_fixup_table[] = { + { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL }, + #ifdef AMD_BOOTLOC_BUG +@@ -252,6 +294,9 @@ static struct cfi_fixup fixup_table[] = + */ + { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip, NULL }, + { CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock, NULL }, ++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC ++ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, }, ++#endif + { 0, 0, NULL, NULL } + }; + +Index: linux-2.6.25/drivers/mtd/chips/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/chips/Kconfig ++++ linux-2.6.25/drivers/mtd/chips/Kconfig +@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD + provides support for one of those command sets, used on chips + including the AMD Am29LV320. + ++config MTD_CFI_FIXUP_MACRONIX_BOOTLOC ++ bool "Fix boot-block location for Macronix flash chips" ++ depends on MTD_CFI_AMDSTD ++ help ++ Some Macronix flash chips have no/wrong boot-block location in the ++ CFI table, and the driver may detect the type incorrectly. Select ++ this if your board has such chip. ++ + config MTD_CFI_STAA + tristate "Support for ST (Advanced Architecture) flash chips" + depends on MTD_GEN_PROBE diff --git a/target/linux/adm5120/patches-2.6.25/102-jedec_pmc_39lvxxx_chips.patch b/target/linux/adm5120/patches-2.6.25/102-jedec_pmc_39lvxxx_chips.patch new file mode 100644 index 0000000000..72665d7f19 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/102-jedec_pmc_39lvxxx_chips.patch @@ -0,0 +1,74 @@ +Index: linux-2.6.25/drivers/mtd/chips/jedec_probe.c +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/chips/jedec_probe.c ++++ linux-2.6.25/drivers/mtd/chips/jedec_probe.c +@@ -121,6 +121,10 @@ + #define UPD29F064115 0x221C + + /* PMC */ ++#define PM39LV512 0x001B ++#define PM39LV010 0x001C ++#define PM39LV020 0x003D ++#define PM39LV040 0x003E + #define PM49FL002 0x006D + #define PM49FL004 0x006E + #define PM49FL008 0x006A +@@ -1170,6 +1174,58 @@ static const struct amd_flash_info jedec + ERASEINFO(0x02000,2), + ERASEINFO(0x04000,1), + } ++ }, { ++ .mfr_id = MANUFACTURER_PMC, ++ .dev_id = PM39LV512, ++ .name = "PMC Pm39LV512", ++ .uaddr = { ++ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */ ++ }, ++ .DevSize = SIZE_64KiB, ++ .CmdSet = P_ID_AMD_STD, ++ .NumEraseRegions= 1, ++ .regions = { ++ ERASEINFO(0x01000,16), ++ } ++ }, { ++ .mfr_id = MANUFACTURER_PMC, ++ .dev_id = PM39LV010, ++ .name = "PMC Pm39LV010", ++ .uaddr = { ++ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */ ++ }, ++ .DevSize = SIZE_128KiB, ++ .CmdSet = P_ID_AMD_STD, ++ .NumEraseRegions= 1, ++ .regions = { ++ ERASEINFO(0x01000,32), ++ } ++ }, { ++ .mfr_id = MANUFACTURER_PMC, ++ .dev_id = PM39LV020, ++ .name = "PMC Pm39LV020", ++ .uaddr = { ++ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */ ++ }, ++ .DevSize = SIZE_256KiB, ++ .CmdSet = P_ID_AMD_STD, ++ .NumEraseRegions= 1, ++ .regions = { ++ ERASEINFO(0x01000,64), ++ } ++ }, { ++ .mfr_id = MANUFACTURER_PMC, ++ .dev_id = PM39LV040, ++ .name = "PMC Pm39LV040", ++ .uaddr = { ++ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */ ++ }, ++ .DevSize = SIZE_512KiB, ++ .CmdSet = P_ID_AMD_STD, ++ .NumEraseRegions= 1, ++ .regions = { ++ ERASEINFO(0x01000,128), ++ } + }, { + .mfr_id = MANUFACTURER_PMC, + .dev_id = PM49FL002, diff --git a/target/linux/adm5120/patches-2.6.25/103-mtd_trxsplit.patch b/target/linux/adm5120/patches-2.6.25/103-mtd_trxsplit.patch new file mode 100644 index 0000000000..c40bfadf4b --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/103-mtd_trxsplit.patch @@ -0,0 +1,28 @@ +Index: linux-2.6.25/drivers/mtd/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/Kconfig ++++ linux-2.6.25/drivers/mtd/Kconfig +@@ -57,6 +57,11 @@ config MTD_ROOTFS_SPLIT + depends on MTD_PARTITIONS + default y + ++config MTD_TRXSPLIT ++ bool "Automatically find and split TRX partitions" ++ depends on MTD_PARTITIONS ++ default n ++ + config MTD_REDBOOT_PARTS + tristate "RedBoot partition table parsing" + depends on MTD_PARTITIONS +Index: linux-2.6.25/drivers/mtd/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/mtd/Makefile ++++ linux-2.6.25/drivers/mtd/Makefile +@@ -8,6 +8,7 @@ mtd-y := mtdcore.o mtdsuper.o + mtd-$(CONFIG_MTD_PARTITIONS) += mtdpart.o + + obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o ++obj-$(CONFIG_MTD_TRXSPLIT) += trxsplit.o + obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o + obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o + obj-$(CONFIG_MTD_AFS_PARTS) += afs.o diff --git a/target/linux/adm5120/patches-2.6.25/120-rb153_cf_driver.patch b/target/linux/adm5120/patches-2.6.25/120-rb153_cf_driver.patch new file mode 100644 index 0000000000..13052be252 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/120-rb153_cf_driver.patch @@ -0,0 +1,30 @@ +Index: linux-2.6.25/drivers/ata/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/ata/Makefile ++++ linux-2.6.25/drivers/ata/Makefile +@@ -71,6 +71,7 @@ obj-$(CONFIG_PATA_BF54X) += pata_bf54x.o + obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o + obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o + obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o ++obj-$(CONFIG_PATA_RB153_CF) += pata_rb153_cf.o + # Should be last but two libata driver + obj-$(CONFIG_PATA_ACPI) += pata_acpi.o + # Should be last but one libata driver +Index: linux-2.6.25/drivers/ata/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/ata/Kconfig ++++ linux-2.6.25/drivers/ata/Kconfig +@@ -679,4 +679,13 @@ config PATA_BF54X + + If unsure, say N. + ++config PATA_RB153_CF ++ tristate "RouterBOARD 153 Compact Flash support" ++ depends on MIPS_ADM5120 ++ help ++ This option enables support for a Compact Flash connected on ++ the RouterBOARD 153. ++ ++ If unsure, say N. ++ + endif # ATA diff --git a/target/linux/adm5120/patches-2.6.25/140-cmdline_hack.patch b/target/linux/adm5120/patches-2.6.25/140-cmdline_hack.patch new file mode 100644 index 0000000000..ab0d99be8a --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/140-cmdline_hack.patch @@ -0,0 +1,17 @@ +Index: linux-2.6.25/arch/mips/kernel/head.S +=================================================================== +--- linux-2.6.25.orig/arch/mips/kernel/head.S ++++ linux-2.6.25/arch/mips/kernel/head.S +@@ -126,7 +126,12 @@ + /* + * Reserved space for exception handlers. + * Necessary for machines which link their kernels at KSEG0. ++ * Use as temporary storage for the kernel command line, so that it ++ * can be updated easily without having to relink the kernel. + */ ++ ++EXPORT(_image_cmdline) ++ .ascii "CMDLINE:" + .fill 0x400 + #endif + diff --git a/target/linux/adm5120/patches-2.6.25/200-amba_pl010_hacks.patch b/target/linux/adm5120/patches-2.6.25/200-amba_pl010_hacks.patch new file mode 100644 index 0000000000..534d043b2e --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/200-amba_pl010_hacks.patch @@ -0,0 +1,297 @@ +Index: linux-2.6.25/drivers/serial/amba-pl010.c +=================================================================== +--- linux-2.6.25.orig/drivers/serial/amba-pl010.c ++++ linux-2.6.25/drivers/serial/amba-pl010.c +@@ -52,11 +52,10 @@ + + #include <asm/io.h> + +-#define UART_NR 8 +- + #define SERIAL_AMBA_MAJOR 204 + #define SERIAL_AMBA_MINOR 16 +-#define SERIAL_AMBA_NR UART_NR ++#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS ++#define SERIAL_AMBA_NAME CONFIG_SERIAL_AMBA_PL010_PORTNAME + + #define AMBA_ISR_PASS_LIMIT 256 + +@@ -82,7 +81,7 @@ static void pl010_stop_tx(struct uart_po + struct uart_amba_port *uap = (struct uart_amba_port *)port; + unsigned int cr; + +- cr = readb(uap->port.membase + UART010_CR); ++ cr = readl(uap->port.membase + UART010_CR); + cr &= ~UART010_CR_TIE; + writel(cr, uap->port.membase + UART010_CR); + } +@@ -92,7 +91,7 @@ static void pl010_start_tx(struct uart_p + struct uart_amba_port *uap = (struct uart_amba_port *)port; + unsigned int cr; + +- cr = readb(uap->port.membase + UART010_CR); ++ cr = readl(uap->port.membase + UART010_CR); + cr |= UART010_CR_TIE; + writel(cr, uap->port.membase + UART010_CR); + } +@@ -102,7 +101,7 @@ static void pl010_stop_rx(struct uart_po + struct uart_amba_port *uap = (struct uart_amba_port *)port; + unsigned int cr; + +- cr = readb(uap->port.membase + UART010_CR); ++ cr = readl(uap->port.membase + UART010_CR); + cr &= ~(UART010_CR_RIE | UART010_CR_RTIE); + writel(cr, uap->port.membase + UART010_CR); + } +@@ -112,7 +111,7 @@ static void pl010_enable_ms(struct uart_ + struct uart_amba_port *uap = (struct uart_amba_port *)port; + unsigned int cr; + +- cr = readb(uap->port.membase + UART010_CR); ++ cr = readl(uap->port.membase + UART010_CR); + cr |= UART010_CR_MSIE; + writel(cr, uap->port.membase + UART010_CR); + } +@@ -122,9 +121,9 @@ static void pl010_rx_chars(struct uart_a + struct tty_struct *tty = uap->port.info->tty; + unsigned int status, ch, flag, rsr, max_count = 256; + +- status = readb(uap->port.membase + UART01x_FR); ++ status = readl(uap->port.membase + UART01x_FR); + while (UART_RX_DATA(status) && max_count--) { +- ch = readb(uap->port.membase + UART01x_DR); ++ ch = readl(uap->port.membase + UART01x_DR); + flag = TTY_NORMAL; + + uap->port.icount.rx++; +@@ -133,7 +132,7 @@ static void pl010_rx_chars(struct uart_a + * Note that the error handling code is + * out of the main execution path + */ +- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX; ++ rsr = readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX; + if (unlikely(rsr & UART01x_RSR_ANY)) { + writel(0, uap->port.membase + UART01x_ECR); + +@@ -165,7 +164,7 @@ static void pl010_rx_chars(struct uart_a + uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag); + + ignore_char: +- status = readb(uap->port.membase + UART01x_FR); ++ status = readl(uap->port.membase + UART01x_FR); + } + spin_unlock(&uap->port.lock); + tty_flip_buffer_push(tty); +@@ -210,7 +209,7 @@ static void pl010_modem_status(struct ua + + writel(0, uap->port.membase + UART010_ICR); + +- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; ++ status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; + + delta = status ^ uap->old_status; + uap->old_status = status; +@@ -238,7 +237,7 @@ static irqreturn_t pl010_int(int irq, vo + + spin_lock(&uap->port.lock); + +- status = readb(uap->port.membase + UART010_IIR); ++ status = readl(uap->port.membase + UART010_IIR); + if (status) { + do { + if (status & (UART010_IIR_RTIS | UART010_IIR_RIS)) +@@ -251,7 +250,7 @@ static irqreturn_t pl010_int(int irq, vo + if (pass_counter-- == 0) + break; + +- status = readb(uap->port.membase + UART010_IIR); ++ status = readl(uap->port.membase + UART010_IIR); + } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS | + UART010_IIR_TIS)); + handled = 1; +@@ -265,7 +264,7 @@ static irqreturn_t pl010_int(int irq, vo + static unsigned int pl010_tx_empty(struct uart_port *port) + { + struct uart_amba_port *uap = (struct uart_amba_port *)port; +- unsigned int status = readb(uap->port.membase + UART01x_FR); ++ unsigned int status = readl(uap->port.membase + UART01x_FR); + return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT; + } + +@@ -275,7 +274,7 @@ static unsigned int pl010_get_mctrl(stru + unsigned int result = 0; + unsigned int status; + +- status = readb(uap->port.membase + UART01x_FR); ++ status = readl(uap->port.membase + UART01x_FR); + if (status & UART01x_FR_DCD) + result |= TIOCM_CAR; + if (status & UART01x_FR_DSR) +@@ -301,7 +300,7 @@ static void pl010_break_ctl(struct uart_ + unsigned int lcr_h; + + spin_lock_irqsave(&uap->port.lock, flags); +- lcr_h = readb(uap->port.membase + UART010_LCRH); ++ lcr_h = readl(uap->port.membase + UART010_LCRH); + if (break_state == -1) + lcr_h |= UART01x_LCRH_BRK; + else +@@ -334,7 +333,7 @@ static int pl010_startup(struct uart_por + /* + * initialise the old status of the modem signals + */ +- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; ++ uap->old_status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; + + /* + * Finally, enable interrupts +@@ -365,7 +364,7 @@ static void pl010_shutdown(struct uart_p + writel(0, uap->port.membase + UART010_CR); + + /* disable break condition and fifos */ +- writel(readb(uap->port.membase + UART010_LCRH) & ++ writel(readl(uap->port.membase + UART010_LCRH) & + ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN), + uap->port.membase + UART010_LCRH); + +@@ -387,7 +386,7 @@ pl010_set_termios(struct uart_port *port + /* + * Ask the core to calculate the divisor for us. + */ +- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); ++ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); + quot = uart_get_divisor(port, baud); + + switch (termios->c_cflag & CSIZE) { +@@ -450,7 +449,7 @@ pl010_set_termios(struct uart_port *port + uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX; + + /* first, disable everything */ +- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE; ++ old_cr = readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE; + + if (UART_ENABLE_MS(port, termios->c_cflag)) + old_cr |= UART010_CR_MSIE; +@@ -540,7 +539,7 @@ static struct uart_ops amba_pl010_pops = + .verify_port = pl010_verify_port, + }; + +-static struct uart_amba_port *amba_ports[UART_NR]; ++static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR]; + + #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE + +@@ -550,7 +549,7 @@ static void pl010_console_putchar(struct + unsigned int status; + + do { +- status = readb(uap->port.membase + UART01x_FR); ++ status = readl(uap->port.membase + UART01x_FR); + barrier(); + } while (!UART_TX_READY(status)); + writel(ch, uap->port.membase + UART01x_DR); +@@ -567,7 +566,7 @@ pl010_console_write(struct console *co, + /* + * First save the CR then disable the interrupts + */ +- old_cr = readb(uap->port.membase + UART010_CR); ++ old_cr = readl(uap->port.membase + UART010_CR); + writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR); + + uart_console_write(&uap->port, s, count, pl010_console_putchar); +@@ -577,7 +576,7 @@ pl010_console_write(struct console *co, + * and restore the TCR + */ + do { +- status = readb(uap->port.membase + UART01x_FR); ++ status = readl(uap->port.membase + UART01x_FR); + barrier(); + } while (status & UART01x_FR_BUSY); + writel(old_cr, uap->port.membase + UART010_CR); +@@ -589,9 +588,9 @@ static void __init + pl010_console_get_options(struct uart_amba_port *uap, int *baud, + int *parity, int *bits) + { +- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) { ++ if (readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) { + unsigned int lcr_h, quot; +- lcr_h = readb(uap->port.membase + UART010_LCRH); ++ lcr_h = readl(uap->port.membase + UART010_LCRH); + + *parity = 'n'; + if (lcr_h & UART01x_LCRH_PEN) { +@@ -606,8 +605,8 @@ pl010_console_get_options(struct uart_am + else + *bits = 8; + +- quot = readb(uap->port.membase + UART010_LCRL) | +- readb(uap->port.membase + UART010_LCRM) << 8; ++ quot = readl(uap->port.membase + UART010_LCRL) | ++ readl(uap->port.membase + UART010_LCRM) << 8; + *baud = uap->port.uartclk / (16 * (quot + 1)); + } + } +@@ -625,7 +624,7 @@ static int __init pl010_console_setup(st + * if so, search for the first available port that does have + * console support. + */ +- if (co->index >= UART_NR) ++ if (co->index >= SERIAL_AMBA_NR) + co->index = 0; + uap = amba_ports[co->index]; + if (!uap) +@@ -643,7 +642,7 @@ static int __init pl010_console_setup(st + + static struct uart_driver amba_reg; + static struct console amba_console = { +- .name = "ttyAM", ++ .name = SERIAL_AMBA_NAME, + .write = pl010_console_write, + .device = uart_console_device, + .setup = pl010_console_setup, +@@ -659,11 +658,11 @@ static struct console amba_console = { + + static struct uart_driver amba_reg = { + .owner = THIS_MODULE, +- .driver_name = "ttyAM", +- .dev_name = "ttyAM", ++ .driver_name = SERIAL_AMBA_NAME, ++ .dev_name = SERIAL_AMBA_NAME, + .major = SERIAL_AMBA_MAJOR, + .minor = SERIAL_AMBA_MINOR, +- .nr = UART_NR, ++ .nr = SERIAL_AMBA_NR, + .cons = AMBA_CONSOLE, + }; + +Index: linux-2.6.25/drivers/serial/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/serial/Kconfig ++++ linux-2.6.25/drivers/serial/Kconfig +@@ -287,10 +287,25 @@ config SERIAL_AMBA_PL010 + help + This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have + an Integrator/AP or Integrator/PP2 platform, or if you have a +- Cirrus Logic EP93xx CPU, say Y or M here. ++ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here. + + If unsure, say N. + ++config SERIAL_AMBA_PL010_NUMPORTS ++ int "Maximum number of AMBA PL010 serial ports" ++ depends on SERIAL_AMBA_PL010 ++ default "8" ++ ---help--- ++ Set this to the number of serial ports you want the AMBA PL010 driver ++ to support. ++ ++config SERIAL_AMBA_PL010_PORTNAME ++ string "Name of the AMBA PL010 serial ports" ++ depends on SERIAL_AMBA_PL010 ++ default "ttyAM" ++ ---help--- ++ ::: To be written ::: ++ + config SERIAL_AMBA_PL010_CONSOLE + bool "Support for console on AMBA serial port" + depends on SERIAL_AMBA_PL010=y diff --git a/target/linux/adm5120/patches-2.6.25/201-amba_bus_hacks.patch b/target/linux/adm5120/patches-2.6.25/201-amba_bus_hacks.patch new file mode 100644 index 0000000000..8a48215d86 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/201-amba_bus_hacks.patch @@ -0,0 +1,15 @@ +Index: linux-2.6.25/drivers/amba/bus.c +=================================================================== +--- linux-2.6.25.orig/drivers/amba/bus.c ++++ linux-2.6.25/drivers/amba/bus.c +@@ -17,6 +17,10 @@ + #include <asm/io.h> + #include <asm/sizes.h> + ++#ifndef NO_IRQ ++#define NO_IRQ (-1) ++#endif ++ + #define to_amba_device(d) container_of(d, struct amba_device, dev) + #define to_amba_driver(d) container_of(d, struct amba_driver, drv) + diff --git a/target/linux/adm5120/patches-2.6.25/202-pci_disable_common_quirks.patch b/target/linux/adm5120/patches-2.6.25/202-pci_disable_common_quirks.patch new file mode 100644 index 0000000000..7a8753fcdf --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/202-pci_disable_common_quirks.patch @@ -0,0 +1,50 @@ +Index: linux-2.6.25/drivers/pci/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/pci/Kconfig ++++ linux-2.6.25/drivers/pci/Kconfig +@@ -42,6 +42,12 @@ config PCI_DEBUG + + When in doubt, say N. + ++config PCI_DISABLE_COMMON_QUIRKS ++ bool "PCI disable common quirks" ++ depends on PCI ++ help ++ If you don't know what to do here, say N. ++ + config HT_IRQ + bool "Interrupts on hypertransport devices" + default y +Index: linux-2.6.25/drivers/pci/quirks.c +=================================================================== +--- linux-2.6.25.orig/drivers/pci/quirks.c ++++ linux-2.6.25/drivers/pci/quirks.c +@@ -24,6 +24,7 @@ + #include <linux/kallsyms.h> + #include "pci.h" + ++#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS + /* The Mellanox Tavor device gives false positive parity errors + * Mark this device with a broken_parity_status, to allow + * PCI scanning code to "skip" this now blacklisted device. +@@ -1495,6 +1496,7 @@ static void __devinit fixup_rev1_53c810( + } + } + DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); ++#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */ + + static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end) + { +@@ -1562,6 +1564,7 @@ void pci_fixup_device(enum pci_fixup_pas + } + EXPORT_SYMBOL(pci_fixup_device); + ++#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS + /* Enable 1k I/O space granularity on the Intel P64H2 */ + static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev) + { +@@ -1875,3 +1878,4 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AT + quirk_msi_intx_disable_bug); + + #endif /* CONFIG_PCI_MSI */ ++#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */ diff --git a/target/linux/adm5120/patches-2.6.25/203-gpio_leds_brightness.patch b/target/linux/adm5120/patches-2.6.25/203-gpio_leds_brightness.patch new file mode 100644 index 0000000000..d00794631f --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/203-gpio_leds_brightness.patch @@ -0,0 +1,29 @@ +Index: linux-2.6.25/drivers/leds/leds-gpio.c +=================================================================== +--- linux-2.6.25.orig/drivers/leds/leds-gpio.c ++++ linux-2.6.25/drivers/leds/leds-gpio.c +@@ -41,13 +41,17 @@ static void gpio_led_set(struct led_clas + container_of(led_cdev, struct gpio_led_data, cdev); + int level; + +- if (value == LED_OFF) +- level = 0; +- else +- level = 1; +- +- if (led_dat->active_low) +- level = !level; ++ switch (value) { ++ case LED_OFF: ++ level = led_dat->active_low ? 1 : 0; ++ break; ++ case LED_FULL: ++ level = led_dat->active_low ? 0 : 1; ++ break; ++ default: ++ level = value; ++ break; ++ } + + /* Setting GPIOs with I2C/etc requires a task context, and we don't + * seem to have a reliable way to know if we're already in one; so diff --git a/target/linux/adm5120/patches-2.6.25/310-adm5120_wdt.patch b/target/linux/adm5120/patches-2.6.25/310-adm5120_wdt.patch new file mode 100644 index 0000000000..695a455d83 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/310-adm5120_wdt.patch @@ -0,0 +1,35 @@ +Index: linux-2.6.25/drivers/watchdog/Kconfig +=================================================================== +--- linux-2.6.25.orig/drivers/watchdog/Kconfig ++++ linux-2.6.25/drivers/watchdog/Kconfig +@@ -619,6 +619,18 @@ config SBC_EPX_C3_WATCHDOG + + # MIPS Architecture + ++config ADM5120_WDT ++ tristate "Infineon ADM5120 SoC hardware watchdog" ++ depends on WATCHDOG && MIPS_ADM5120 ++ help ++ This is a driver for hardware watchdog integrated in Infineon ++ ADM5120 SoC. This watchdog simply watches your kernel to make sure ++ it doesn't freeze, and if it does, it reboots your computer after a ++ certain amount of time. ++ ++ To compile this driver as a module, choose M here: the module will be ++ called adm5120_wdt. ++ + config INDYDOG + tristate "Indy/I2 Hardware Watchdog" + depends on SGI_HAS_INDYDOG +Index: linux-2.6.25/drivers/watchdog/Makefile +=================================================================== +--- linux-2.6.25.orig/drivers/watchdog/Makefile ++++ linux-2.6.25/drivers/watchdog/Makefile +@@ -90,6 +90,7 @@ obj-$(CONFIG_SBC_EPX_C3_WATCHDOG) += sbc + # M68KNOMMU Architecture + + # MIPS Architecture ++obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o + obj-$(CONFIG_INDYDOG) += indydog.o + obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o + obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o diff --git a/target/linux/adm5120/patches-2.6.25/900-usb_bump_version_number.patch b/target/linux/adm5120/patches-2.6.25/900-usb_bump_version_number.patch new file mode 100644 index 0000000000..6d7fa6b69d --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/900-usb_bump_version_number.patch @@ -0,0 +1,13 @@ +Index: linux-2.6.25/drivers/usb/host/adm5120-hcd.c +=================================================================== +--- linux-2.6.25.orig/drivers/usb/host/adm5120-hcd.c ++++ linux-2.6.25/drivers/usb/host/adm5120-hcd.c +@@ -45,7 +45,7 @@ + #include "../core/hcd.h" + #include "../core/hub.h" + +-#define DRIVER_VERSION "0.24.0" ++#define DRIVER_VERSION "0.25.0" + #define DRIVER_AUTHOR "Gabor Juhos <juhosg at openwrt.org>" + #define DRIVER_DESC "ADMtek USB 1.1 Host Controller Driver" + diff --git a/target/linux/adm5120/patches-2.6.25/901-usb_convert_from_class_device.patch b/target/linux/adm5120/patches-2.6.25/901-usb_convert_from_class_device.patch new file mode 100644 index 0000000000..62953b47c1 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/901-usb_convert_from_class_device.patch @@ -0,0 +1,109 @@ +Index: linux-2.6.25/drivers/usb/host/adm5120-dbg.c +=================================================================== +--- linux-2.6.25.orig/drivers/usb/host/adm5120-dbg.c ++++ linux-2.6.25/drivers/usb/host/adm5120-dbg.c +@@ -456,7 +456,7 @@ show_list(struct admhcd *ahcd, char *buf + } + + static ssize_t +-show_async(struct class_device *class_dev, char *buf) ++show_async(struct device *dev, struct device_attribute *attr, char *buf) + { + struct usb_bus *bus; + struct usb_hcd *hcd; +@@ -464,7 +464,7 @@ show_async(struct class_device *class_de + size_t temp; + unsigned long flags; + +- bus = class_get_devdata(class_dev); ++ bus = dev_get_drvdata(dev); + hcd = bus_to_hcd(bus); + ahcd = hcd_to_admhcd(hcd); + +@@ -475,13 +475,13 @@ show_async(struct class_device *class_de + + return temp; + } +-static CLASS_DEVICE_ATTR(async, S_IRUGO, show_async, NULL); ++static DEVICE_ATTR(async, S_IRUGO, show_async, NULL); + + + #define DBG_SCHED_LIMIT 64 + + static ssize_t +-show_periodic(struct class_device *class_dev, char *buf) ++show_periodic(struct device *dev, struct device_attribute *attr, char *buf) + { + struct usb_bus *bus; + struct usb_hcd *hcd; +@@ -496,7 +496,7 @@ show_periodic(struct class_device *class + return 0; + seen_count = 0; + +- bus = class_get_devdata(class_dev); ++ bus = dev_get_drvdata(dev); + hcd = bus_to_hcd(bus); + ahcd = hcd_to_admhcd(hcd); + next = buf; +@@ -574,13 +574,13 @@ show_periodic(struct class_device *class + + return PAGE_SIZE - size; + } +-static CLASS_DEVICE_ATTR(periodic, S_IRUGO, show_periodic, NULL); ++static DEVICE_ATTR(periodic, S_IRUGO, show_periodic, NULL); + + + #undef DBG_SCHED_LIMIT + + static ssize_t +-show_registers(struct class_device *class_dev, char *buf) ++show_registers(struct device *dev, struct device_attribute *attr, char *buf) + { + struct usb_bus *bus; + struct usb_hcd *hcd; +@@ -591,7 +591,7 @@ show_registers(struct class_device *clas + char *next; + u32 rdata; + +- bus = class_get_devdata(class_dev); ++ bus = dev_get_drvdata(dev); + hcd = bus_to_hcd(bus); + ahcd = hcd_to_admhcd(hcd); + regs = ahcd->regs; +@@ -656,27 +656,27 @@ done: + spin_unlock_irqrestore(&ahcd->lock, flags); + return PAGE_SIZE - size; + } +-static CLASS_DEVICE_ATTR(registers, S_IRUGO, show_registers, NULL); ++static DEVICE_ATTR(registers, S_IRUGO, show_registers, NULL); + + + static inline void create_debug_files (struct admhcd *ahcd) + { +- struct class_device *cldev = admhcd_to_hcd(ahcd)->self.class_dev; ++ struct device *dev = admhcd_to_hcd(ahcd)->self.dev; + int retval; + +- retval = class_device_create_file(cldev, &class_device_attr_async); +- retval = class_device_create_file(cldev, &class_device_attr_periodic); +- retval = class_device_create_file(cldev, &class_device_attr_registers); ++ retval = device_create_file(dev, &dev_attr_async); ++ retval = device_create_file(dev, &dev_attr_periodic); ++ retval = device_create_file(dev, &dev_attr_registers); + admhc_dbg(ahcd, "created debug files\n"); + } + + static inline void remove_debug_files (struct admhcd *ahcd) + { +- struct class_device *cldev = admhcd_to_hcd(ahcd)->self.class_dev; ++ struct device *dev = admhcd_to_hcd(ahcd)->self.dev; + +- class_device_remove_file(cldev, &class_device_attr_async); +- class_device_remove_file(cldev, &class_device_attr_periodic); +- class_device_remove_file(cldev, &class_device_attr_registers); ++ device_remove_file(dev, &dev_attr_async); ++ device_remove_file(dev, &dev_attr_periodic); ++ device_remove_file(dev, &dev_attr_registers); + } + + #endif diff --git a/target/linux/adm5120/patches-2.6.25/902-usb_use_debugfs_instead_of_sysfs.patch b/target/linux/adm5120/patches-2.6.25/902-usb_use_debugfs_instead_of_sysfs.patch new file mode 100644 index 0000000000..ee14a247ae --- /dev/null +++ b/target/linux/adm5120/patches-2.6.25/902-usb_use_debugfs_instead_of_sysfs.patch @@ -0,0 +1,363 @@ +Index: linux-2.6.25/drivers/usb/host/adm5120.h +=================================================================== +--- linux-2.6.25.orig/drivers/usb/host/adm5120.h ++++ linux-2.6.25/drivers/usb/host/adm5120.h +@@ -431,6 +431,13 @@ struct admhcd { + #define OHCI_QUIRK_BE_MMIO 0x10 /* BE registers */ + #define OHCI_QUIRK_ZFMICRO 0x20 /* Compaq ZFMicro chipset*/ + // there are also chip quirks/bugs in init logic ++ ++#ifdef DEBUG ++ struct dentry *debug_dir; ++ struct dentry *debug_async; ++ struct dentry *debug_periodic; ++ struct dentry *debug_registers; ++#endif + }; + + /* convert between an hcd pointer and the corresponding ahcd_hcd */ +Index: linux-2.6.25/drivers/usb/host/adm5120-hcd.c +=================================================================== +--- linux-2.6.25.orig/drivers/usb/host/adm5120-hcd.c ++++ linux-2.6.25/drivers/usb/host/adm5120-hcd.c +@@ -35,6 +35,7 @@ + #include <linux/dma-mapping.h> + #include <linux/dmapool.h> + #include <linux/reboot.h> ++#include <linux/debugfs.h> + + #include <asm/io.h> + #include <asm/irq.h> +@@ -799,6 +800,14 @@ static int __init admhc_hcd_mod_init(voi + pr_info("%s: block sizes: ed %Zd td %Zd\n", hcd_name, + sizeof (struct ed), sizeof (struct td)); + ++#ifdef DEBUG ++ admhc_debug_root = debugfs_create_dir("admhc", NULL); ++ if (!admhc_debug_root) { ++ ret = -ENOENT; ++ goto error_debug; ++ } ++#endif ++ + #ifdef PLATFORM_DRIVER + ret = platform_driver_register(&PLATFORM_DRIVER); + if (ret < 0) +@@ -811,6 +820,12 @@ static int __init admhc_hcd_mod_init(voi + platform_driver_unregister(&PLATFORM_DRIVER); + error_platform: + #endif ++ ++#ifdef DEBUG ++ debugfs_remove(admhc_debug_root); ++ admhc_debug_root = NULL; ++error_debug: ++#endif + return ret; + } + module_init(admhc_hcd_mod_init); +@@ -818,6 +833,9 @@ module_init(admhc_hcd_mod_init); + static void __exit admhc_hcd_mod_exit(void) + { + platform_driver_unregister(&PLATFORM_DRIVER); ++#ifdef DEBUG ++ debugfs_remove(admhc_debug_root); ++#endif + } + module_exit(admhc_hcd_mod_exit); + +Index: linux-2.6.25/drivers/usb/host/adm5120-dbg.c +=================================================================== +--- linux-2.6.25.orig/drivers/usb/host/adm5120-dbg.c ++++ linux-2.6.25/drivers/usb/host/adm5120-dbg.c +@@ -390,6 +390,42 @@ static inline void remove_debug_files(st + + #else + ++static int debug_async_open(struct inode *, struct file *); ++static int debug_periodic_open(struct inode *, struct file *); ++static int debug_registers_open(struct inode *, struct file *); ++static int debug_async_open(struct inode *, struct file *); ++static ssize_t debug_output(struct file*, char __user*, size_t, loff_t*); ++static int debug_close(struct inode *, struct file *); ++ ++static const struct file_operations debug_async_fops = { ++ .owner = THIS_MODULE, ++ .open = debug_async_open, ++ .read = debug_output, ++ .release = debug_close, ++}; ++static const struct file_operations debug_periodic_fops = { ++ .owner = THIS_MODULE, ++ .open = debug_periodic_open, ++ .read = debug_output, ++ .release = debug_close, ++}; ++static const struct file_operations debug_registers_fops = { ++ .owner = THIS_MODULE, ++ .open = debug_registers_open, ++ .read = debug_output, ++ .release = debug_close, ++}; ++ ++static struct dentry *admhc_debug_root; ++ ++struct debug_buffer { ++ ssize_t (*fill_func)(struct debug_buffer *); /* fill method */ ++ struct device *dev; ++ struct mutex mutex; /* protect filling of buffer */ ++ size_t count; /* number of characters filled into buffer */ ++ char *page; ++}; ++ + static ssize_t + show_list(struct admhcd *ahcd, char *buf, size_t count, struct ed *ed) + { +@@ -455,8 +491,7 @@ show_list(struct admhcd *ahcd, char *buf + return count - size; + } + +-static ssize_t +-show_async(struct device *dev, struct device_attribute *attr, char *buf) ++static ssize_t fill_async_buffer(struct debug_buffer *buf) + { + struct usb_bus *bus; + struct usb_hcd *hcd; +@@ -464,24 +499,22 @@ show_async(struct device *dev, struct de + size_t temp; + unsigned long flags; + +- bus = dev_get_drvdata(dev); ++ bus = dev_get_drvdata(buf->dev); + hcd = bus_to_hcd(bus); + ahcd = hcd_to_admhcd(hcd); + + /* display control and bulk lists together, for simplicity */ + spin_lock_irqsave(&ahcd->lock, flags); +- temp = show_list(ahcd, buf, PAGE_SIZE, ahcd->ed_head); ++ temp = show_list(ahcd, buf->page, buf->count, ahcd->ed_head); + spin_unlock_irqrestore(&ahcd->lock, flags); + + return temp; + } +-static DEVICE_ATTR(async, S_IRUGO, show_async, NULL); + + + #define DBG_SCHED_LIMIT 64 + +-static ssize_t +-show_periodic(struct device *dev, struct device_attribute *attr, char *buf) ++static ssize_t fill_periodic_buffer(struct debug_buffer *buf) + { + struct usb_bus *bus; + struct usb_hcd *hcd; +@@ -496,10 +529,10 @@ show_periodic(struct device *dev, struct + return 0; + seen_count = 0; + +- bus = dev_get_drvdata(dev); ++ bus = dev_get_drvdata(buf->dev); + hcd = bus_to_hcd(bus); + ahcd = hcd_to_admhcd(hcd); +- next = buf; ++ next = buf->page; + size = PAGE_SIZE; + + temp = scnprintf(next, size, "size = %d\n", NUM_INTS); +@@ -574,13 +607,11 @@ show_periodic(struct device *dev, struct + + return PAGE_SIZE - size; + } +-static DEVICE_ATTR(periodic, S_IRUGO, show_periodic, NULL); + + + #undef DBG_SCHED_LIMIT + +-static ssize_t +-show_registers(struct device *dev, struct device_attribute *attr, char *buf) ++static ssize_t fill_registers_buffer(struct debug_buffer *buf) + { + struct usb_bus *bus; + struct usb_hcd *hcd; +@@ -591,11 +622,11 @@ show_registers(struct device *dev, struc + char *next; + u32 rdata; + +- bus = dev_get_drvdata(dev); ++ bus = dev_get_drvdata(buf->dev); + hcd = bus_to_hcd(bus); + ahcd = hcd_to_admhcd(hcd); + regs = ahcd->regs; +- next = buf; ++ next = buf->page; + size = PAGE_SIZE; + + spin_lock_irqsave(&ahcd->lock, flags); +@@ -656,27 +687,154 @@ done: + spin_unlock_irqrestore(&ahcd->lock, flags); + return PAGE_SIZE - size; + } +-static DEVICE_ATTR(registers, S_IRUGO, show_registers, NULL); + + +-static inline void create_debug_files (struct admhcd *ahcd) ++static struct debug_buffer *alloc_buffer(struct device *dev, ++ ssize_t (*fill_func)(struct debug_buffer *)) + { +- struct device *dev = admhcd_to_hcd(ahcd)->self.dev; +- int retval; ++ struct debug_buffer *buf; + +- retval = device_create_file(dev, &dev_attr_async); +- retval = device_create_file(dev, &dev_attr_periodic); +- retval = device_create_file(dev, &dev_attr_registers); +- admhc_dbg(ahcd, "created debug files\n"); ++ buf = kzalloc(sizeof(struct debug_buffer), GFP_KERNEL); ++ ++ if (buf) { ++ buf->dev = dev; ++ buf->fill_func = fill_func; ++ mutex_init(&buf->mutex); ++ } ++ ++ return buf; ++} ++ ++static int fill_buffer(struct debug_buffer *buf) ++{ ++ int ret = 0; ++ ++ if (!buf->page) ++ buf->page = (char *)get_zeroed_page(GFP_KERNEL); ++ ++ if (!buf->page) { ++ ret = -ENOMEM; ++ goto out; ++ } ++ ++ ret = buf->fill_func(buf); ++ ++ if (ret >= 0) { ++ buf->count = ret; ++ ret = 0; ++ } ++ ++out: ++ return ret; ++} ++ ++static ssize_t debug_output(struct file *file, char __user *user_buf, ++ size_t len, loff_t *offset) ++{ ++ struct debug_buffer *buf = file->private_data; ++ int ret = 0; ++ ++ mutex_lock(&buf->mutex); ++ if (buf->count == 0) { ++ ret = fill_buffer(buf); ++ if (ret != 0) { ++ mutex_unlock(&buf->mutex); ++ goto out; ++ } ++ } ++ mutex_unlock(&buf->mutex); ++ ++ ret = simple_read_from_buffer(user_buf, len, offset, ++ buf->page, buf->count); ++ ++out: ++ return ret; ++} ++ ++static int debug_close(struct inode *inode, struct file *file) ++{ ++ struct debug_buffer *buf = file->private_data; ++ ++ if (buf) { ++ if (buf->page) ++ free_page((unsigned long)buf->page); ++ kfree(buf); ++ } ++ ++ return 0; + } + +-static inline void remove_debug_files (struct admhcd *ahcd) ++static int debug_async_open(struct inode *inode, struct file *file) + { +- struct device *dev = admhcd_to_hcd(ahcd)->self.dev; ++ file->private_data = alloc_buffer(inode->i_private, fill_async_buffer); ++ ++ return file->private_data ? 0 : -ENOMEM; ++} ++ ++static int debug_periodic_open(struct inode *inode, struct file *file) ++{ ++ file->private_data = alloc_buffer(inode->i_private, ++ fill_periodic_buffer); ++ ++ return file->private_data ? 0 : -ENOMEM; ++} + +- device_remove_file(dev, &dev_attr_async); +- device_remove_file(dev, &dev_attr_periodic); +- device_remove_file(dev, &dev_attr_registers); ++static int debug_registers_open(struct inode *inode, struct file *file) ++{ ++ file->private_data = alloc_buffer(inode->i_private, ++ fill_registers_buffer); ++ ++ return file->private_data ? 0 : -ENOMEM; ++} ++ ++static inline void create_debug_files(struct admhcd *ahcd) ++{ ++ struct usb_bus *bus = &admhcd_to_hcd(ahcd)->self; ++ struct device *dev = bus->dev; ++ ++ ahcd->debug_dir = debugfs_create_dir(bus->bus_name, admhc_debug_root); ++ if (!ahcd->debug_dir) ++ goto dir_error; ++ ++ ahcd->debug_async = debugfs_create_file("async", S_IRUGO, ++ ahcd->debug_dir, dev, ++ &debug_async_fops); ++ if (!ahcd->debug_async) ++ goto async_error; ++ ++ ahcd->debug_periodic = debugfs_create_file("periodic", S_IRUGO, ++ ahcd->debug_dir, dev, ++ &debug_periodic_fops); ++ if (!ahcd->debug_periodic) ++ goto periodic_error; ++ ++ ahcd->debug_registers = debugfs_create_file("registers", S_IRUGO, ++ ahcd->debug_dir, dev, ++ &debug_registers_fops); ++ if (!ahcd->debug_registers) ++ goto registers_error; ++ ++ admhc_dbg(ahcd, "created debug files\n"); ++ return; ++ ++registers_error: ++ debugfs_remove(ahcd->debug_periodic); ++periodic_error: ++ debugfs_remove(ahcd->debug_async); ++async_error: ++ debugfs_remove(ahcd->debug_dir); ++dir_error: ++ ahcd->debug_periodic = NULL; ++ ahcd->debug_async = NULL; ++ ahcd->debug_dir = NULL; ++} ++ ++static inline void remove_debug_files(struct admhcd *ahcd) ++{ ++ debugfs_remove(ahcd->debug_registers); ++ debugfs_remove(ahcd->debug_periodic); ++ debugfs_remove(ahcd->debug_async); ++ debugfs_remove(ahcd->debug_dir); + } + + #endif diff --git a/target/linux/adm5120/router_be/config-2.6.25 b/target/linux/adm5120/router_be/config-2.6.25 new file mode 100644 index 0000000000..690f55b872 --- /dev/null +++ b/target/linux/adm5120/router_be/config-2.6.25 @@ -0,0 +1,278 @@ +CONFIG_32BIT=y +# CONFIG_64BIT is not set +CONFIG_ADM5120_CPU_OVERRIDES=y +CONFIG_ADM5120_WDT=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_POPULATES_NODE_MAP=y +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_ARCH_SUPPORTS_OPROFILE=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM_AMBA=y +CONFIG_BASE_SMALL=0 +CONFIG_BAYCOM_SER_FDX=m +CONFIG_BAYCOM_SER_HDX=m +# CONFIG_BCM47XX is not set +CONFIG_BINFMT_MISC=m +CONFIG_BITREVERSE=y +CONFIG_CEVT_R4K=y +CONFIG_CIFS_DEBUG2=y +CONFIG_CIFS_EXPERIMENTAL=y +CONFIG_CIFS_STATS2=y +CONFIG_CIFS_WEAK_PW_HASH=y +CONFIG_CIFS_XATTR=y +CONFIG_CLASSIC_RCU=y +CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/etc/preinit" +CONFIG_CPU_BIG_ENDIAN=y +CONFIG_CPU_HAS_LLSC=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_SYNC=y +# CONFIG_CPU_LITTLE_ENDIAN is not set +# CONFIG_CPU_LOONGSON2 is not set +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R1=y +# CONFIG_CPU_MIPS32_R2 is not set +# CONFIG_CPU_MIPS64_R1 is not set +# CONFIG_CPU_MIPS64_R2 is not set +CONFIG_CPU_MIPSR1=y +# CONFIG_CPU_NEVADA is not set +# CONFIG_CPU_R10000 is not set +# CONFIG_CPU_R3000 is not set +# CONFIG_CPU_R4300 is not set +# CONFIG_CPU_R4X00 is not set +# CONFIG_CPU_R5000 is not set +# CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R6000 is not set +# CONFIG_CPU_R8000 is not set +# CONFIG_CPU_RM7000 is not set +# CONFIG_CPU_RM9000 is not set +# CONFIG_CPU_SB1 is not set +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +# CONFIG_CPU_TX39XX is not set +# CONFIG_CPU_TX49XX is not set +# CONFIG_CPU_VR41XX is not set +CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AUTHENC=m +CONFIG_CRYPTO_GF128MUL=m +CONFIG_CSRC_R4K=y +CONFIG_DEVPORT=y +# CONFIG_DM9000 is not set +CONFIG_DMA_NEED_PCI_MAP_STATE=y +CONFIG_DMA_NONCOHERENT=y +# CONFIG_E1000E is not set +# CONFIG_E1000E_ENABLED is not set +CONFIG_EARLY_PRINTK=y +CONFIG_ELF_CORE=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +CONFIG_EXT3_FS_XATTR=y +CONFIG_FS_MBCACHE=m +CONFIG_FS_POSIX_ACL=y +CONFIG_GENERIC_ACL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_GPIO=y +# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAVE_IDE=y +# CONFIG_HAVE_KPROBES is not set +# CONFIG_HAVE_KRETPROBES is not set +CONFIG_HAVE_OPROFILE=y +CONFIG_HID=m +CONFIG_HID_SUPPORT=y +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HZ=250 +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_I2C is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IDE is not set +# CONFIG_IGB is not set +CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m +CONFIG_INITRAMFS_SOURCE="" +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_INPUT=m +# CONFIG_INPUT_EVDEV is not set +# CONFIG_IP1000 is not set +CONFIG_IPV6_MIP6=m +CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTE_INFO=y +CONFIG_IPV6_TUNNEL=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m +CONFIG_IRQ_CPU=y +# CONFIG_JOLIET is not set +CONFIG_LEDS_ADM5120=m +# CONFIG_LEDS_ADM5120_DIAG is not set +# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set +# CONFIG_LEDS_ALIX is not set +CONFIG_LEDS_GPIO=m +CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_LEMOTE_FULONG is not set +CONFIG_LZO_COMPRESS=m +CONFIG_LZO_DECOMPRESS=m +# CONFIG_MACH_ALCHEMY is not set +# CONFIG_MACH_DECSTATION is not set +# CONFIG_MACH_JAZZ is not set +# CONFIG_MACH_VR41XX is not set +# CONFIG_MEMSTICK is not set +CONFIG_MII=m +# CONFIG_MINIX_FS is not set +CONFIG_MIPS=y +CONFIG_MIPS_ADM5120=y +CONFIG_MIPS_ADM5120_ENET=y +# CONFIG_MIPS_ATLAS is not set +# CONFIG_MIPS_COBALT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +# CONFIG_MIPS_MALTA is not set +CONFIG_MIPS_MT_DISABLED=y +# CONFIG_MIPS_MT_SMP is not set +# CONFIG_MIPS_MT_SMTC is not set +# CONFIG_MIPS_SEAD is not set +# CONFIG_MIPS_SIM is not set +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MTD=y +# CONFIG_MTD_ABSENT is not set +CONFIG_MTD_ADM5120=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_BLOCK2MTD=y +CONFIG_MTD_CFI=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +CONFIG_MTD_CHAR=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_CONCAT is not set +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_MYLOADER_PARTS is not set +# CONFIG_MTD_ONENAND is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_PCI is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_PLATRAM is not set +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_SLRAM is not set +CONFIG_MTD_TRXSPLIT=y +CONFIG_NETDEV_1000=y +# CONFIG_NET_PCI is not set +# CONFIG_NET_PKTGEN is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NO_IOPORT is not set +# CONFIG_PAGE_SIZE_16KB is not set +CONFIG_PAGE_SIZE_4KB=y +# CONFIG_PAGE_SIZE_64KB is not set +# CONFIG_PAGE_SIZE_8KB is not set +# CONFIG_PARTITION_ADVANCED is not set +# CONFIG_PCIPCWATCHDOG is not set +CONFIG_PCI_ADM5120=y +CONFIG_PCI_DISABLE_COMMON_QUIRKS=y +CONFIG_PCI_DOMAINS=y +# CONFIG_PMC_MSP is not set +# CONFIG_PMC_YOSEMITE is not set +# CONFIG_PNX8550_JBS is not set +# CONFIG_PNX8550_STB810 is not set +# CONFIG_RTC is not set +CONFIG_RTC_LIB=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_SCSI_WAIT_SCAN=m +# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_AMBA_PL010=y +CONFIG_SERIAL_AMBA_PL010_CONSOLE=y +CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2 +CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS" +# CONFIG_SERIAL_AMBA_PL011 is not set +CONFIG_SERIO=y +# CONFIG_SERIO_AMBAKMI is not set +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_SERPORT=y +# CONFIG_SGI_IP22 is not set +# CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP28 is not set +# CONFIG_SGI_IP32 is not set +# CONFIG_SIBYTE_BIGSUR is not set +# CONFIG_SIBYTE_CARMEL is not set +# CONFIG_SIBYTE_CRHINE is not set +# CONFIG_SIBYTE_CRHONE is not set +# CONFIG_SIBYTE_LITTLESUR is not set +# CONFIG_SIBYTE_RHONE is not set +# CONFIG_SIBYTE_SENTOSA is not set +# CONFIG_SIBYTE_SWARM is not set +CONFIG_SLABINFO=y +# CONFIG_SND_USB_AUDIO is not set +CONFIG_SOFT_WATCHDOG=m +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_SSB_POSSIBLE=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y +# CONFIG_THERMAL is not set +CONFIG_TICK_ONESHOT=y +CONFIG_TMPFS_POSIX_ACL=y +# CONFIG_TOSHIBA_JMR3927 is not set +# CONFIG_TOSHIBA_RBTX4927 is not set +# CONFIG_TOSHIBA_RBTX4938 is not set +CONFIG_TRAD_SIGNALS=y +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_USB_ACM is not set +CONFIG_USB_ADM5120_HCD=m +# CONFIG_USB_ATM is not set +# CONFIG_USB_CATC is not set +# CONFIG_USB_DEVICEFS is not set +# CONFIG_USB_EHCI_HCD is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_SERIAL is not set +# CONFIG_USB_STORAGE is not set +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_USBNET is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_V4L2_COMMON=m +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/adm5120/router_le/config-2.6.25 b/target/linux/adm5120/router_le/config-2.6.25 new file mode 100644 index 0000000000..677a984005 --- /dev/null +++ b/target/linux/adm5120/router_le/config-2.6.25 @@ -0,0 +1,293 @@ +CONFIG_32BIT=y +# CONFIG_64BIT is not set +CONFIG_ADM5120_CPU_OVERRIDES=y +CONFIG_ADM5120_WDT=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_POPULATES_NODE_MAP=y +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_ARCH_SUPPORTS_OPROFILE=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM_AMBA=y +CONFIG_BASE_SMALL=0 +CONFIG_BAYCOM_SER_FDX=m +CONFIG_BAYCOM_SER_HDX=m +# CONFIG_BCM47XX is not set +CONFIG_BINFMT_MISC=m +CONFIG_BITREVERSE=y +CONFIG_CEVT_R4K=y +CONFIG_CIFS_DEBUG2=y +CONFIG_CIFS_EXPERIMENTAL=y +CONFIG_CIFS_STATS2=y +CONFIG_CIFS_WEAK_PW_HASH=y +CONFIG_CIFS_XATTR=y +CONFIG_CLASSIC_RCU=y +CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2 init=/etc/preinit" +# CONFIG_CPU_BIG_ENDIAN is not set +CONFIG_CPU_HAS_LLSC=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_LITTLE_ENDIAN=y +# CONFIG_CPU_LOONGSON2 is not set +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R1=y +# CONFIG_CPU_MIPS32_R2 is not set +# CONFIG_CPU_MIPS64_R1 is not set +# CONFIG_CPU_MIPS64_R2 is not set +CONFIG_CPU_MIPSR1=y +# CONFIG_CPU_NEVADA is not set +# CONFIG_CPU_R10000 is not set +# CONFIG_CPU_R3000 is not set +# CONFIG_CPU_R4300 is not set +# CONFIG_CPU_R4X00 is not set +# CONFIG_CPU_R5000 is not set +# CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R6000 is not set +# CONFIG_CPU_R8000 is not set +# CONFIG_CPU_RM7000 is not set +# CONFIG_CPU_RM9000 is not set +# CONFIG_CPU_SB1 is not set +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +# CONFIG_CPU_TX39XX is not set +# CONFIG_CPU_TX49XX is not set +# CONFIG_CPU_VR41XX is not set +CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AUTHENC=m +CONFIG_CRYPTO_GF128MUL=m +CONFIG_CSRC_R4K=y +CONFIG_DEVPORT=y +# CONFIG_DM9000 is not set +CONFIG_DMA_NEED_PCI_MAP_STATE=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_EARLY_PRINTK=y +CONFIG_ELF_CORE=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +CONFIG_EXT3_FS_XATTR=y +CONFIG_FS_MBCACHE=m +CONFIG_FS_POSIX_ACL=y +CONFIG_GENERIC_ACL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_GPIO=y +# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAVE_IDE=y +# CONFIG_HAVE_KPROBES is not set +# CONFIG_HAVE_KRETPROBES is not set +CONFIG_HAVE_OPROFILE=y +CONFIG_HID=m +CONFIG_HID_SUPPORT=y +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HZ=250 +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_I2C is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IDE is not set +CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m +CONFIG_INITRAMFS_SOURCE="" +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_INPUT=m +# CONFIG_INPUT_EVDEV is not set +CONFIG_IPV6_MIP6=m +CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTE_INFO=y +CONFIG_IPV6_TUNNEL=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m +CONFIG_IRQ_CPU=y +# CONFIG_JOLIET is not set +CONFIG_LEDS_ADM5120=m +# CONFIG_LEDS_ADM5120_DIAG is not set +# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set +# CONFIG_LEDS_ALIX is not set +CONFIG_LEDS_GPIO=m +CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_LEMOTE_FULONG is not set +CONFIG_LZO_COMPRESS=m +CONFIG_LZO_DECOMPRESS=m +# CONFIG_MACH_ALCHEMY is not set +# CONFIG_MACH_DECSTATION is not set +# CONFIG_MACH_JAZZ is not set +# CONFIG_MACH_VR41XX is not set +# CONFIG_MEMSTICK is not set +CONFIG_MII=m +# CONFIG_MINIX_FS is not set +CONFIG_MIPS=y +CONFIG_MIPS_ADM5120=y +CONFIG_MIPS_ADM5120_ENET=y +# CONFIG_MIPS_ATLAS is not set +# CONFIG_MIPS_COBALT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +# CONFIG_MIPS_MALTA is not set +CONFIG_MIPS_MT_DISABLED=y +# CONFIG_MIPS_MT_SMP is not set +# CONFIG_MIPS_MT_SMTC is not set +# CONFIG_MIPS_SEAD is not set +# CONFIG_MIPS_SIM is not set +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MTD=y +# CONFIG_MTD_ABSENT is not set +CONFIG_MTD_ADM5120=y +# CONFIG_MTD_ALAUDA is not set +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_MTD_BLOCK2MTD is not set +CONFIG_MTD_CFI=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +CONFIG_MTD_CHAR=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_CONCAT is not set +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MTDRAM is not set +CONFIG_MTD_MYLOADER_PARTS=y +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_CAFE is not set +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_NANDSIM is not set +CONFIG_MTD_NAND_PLATFORM=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_ONENAND is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_PCI is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_PLATRAM is not set +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_SLRAM is not set +CONFIG_MTD_TRXSPLIT=y +# CONFIG_NETFILTER_XT_TARGET_TARPIT is not set +# CONFIG_NET_PCI is not set +# CONFIG_NET_PKTGEN is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NO_IOPORT is not set +# CONFIG_PAGE_SIZE_16KB is not set +CONFIG_PAGE_SIZE_4KB=y +# CONFIG_PAGE_SIZE_64KB is not set +# CONFIG_PAGE_SIZE_8KB is not set +# CONFIG_PARTITION_ADVANCED is not set +# CONFIG_PCIPCWATCHDOG is not set +CONFIG_PCI_ADM5120=y +CONFIG_PCI_DISABLE_COMMON_QUIRKS=y +CONFIG_PCI_DOMAINS=y +# CONFIG_PMC_MSP is not set +# CONFIG_PMC_YOSEMITE is not set +# CONFIG_PNX8550_JBS is not set +# CONFIG_PNX8550_STB810 is not set +# CONFIG_RTC is not set +CONFIG_RTC_LIB=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_SCSI_WAIT_SCAN=m +# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_AMBA_PL010=y +CONFIG_SERIAL_AMBA_PL010_CONSOLE=y +CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2 +CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS" +# CONFIG_SERIAL_AMBA_PL011 is not set +CONFIG_SERIO=y +# CONFIG_SERIO_AMBAKMI is not set +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_SERPORT=y +# CONFIG_SGI_IP22 is not set +# CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP28 is not set +# CONFIG_SGI_IP32 is not set +# CONFIG_SIBYTE_BIGSUR is not set +# CONFIG_SIBYTE_CARMEL is not set +# CONFIG_SIBYTE_CRHINE is not set +# CONFIG_SIBYTE_CRHONE is not set +# CONFIG_SIBYTE_LITTLESUR is not set +# CONFIG_SIBYTE_RHONE is not set +# CONFIG_SIBYTE_SENTOSA is not set +# CONFIG_SIBYTE_SWARM is not set +CONFIG_SLABINFO=y +# CONFIG_SND_HIFIER is not set +# CONFIG_SND_OXYGEN is not set +# CONFIG_SND_VIRTUOSO is not set +CONFIG_SOFT_WATCHDOG=m +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_SSB_POSSIBLE=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y +# CONFIG_THERMAL is not set +CONFIG_TICK_ONESHOT=y +CONFIG_TMPFS_POSIX_ACL=y +# CONFIG_TOSHIBA_JMR3927 is not set +# CONFIG_TOSHIBA_RBTX4927 is not set +# CONFIG_TOSHIBA_RBTX4938 is not set +CONFIG_TRAD_SIGNALS=y +# CONFIG_USBPCWATCHDOG is not set +CONFIG_USB_ADM5120_HCD=m +# CONFIG_USB_ALI_M5632 is not set +# CONFIG_USB_AN2720 is not set +# CONFIG_USB_CATC is not set +CONFIG_USB_DEBUG=y +CONFIG_USB_EHCI_HCD=m +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_NET_DM9601 is not set +# CONFIG_USB_NET_GL620A is not set +# CONFIG_USB_NET_MCS7830 is not set +# CONFIG_USB_NET_PLUSB is not set +# CONFIG_USB_NET_RNDIS_HOST is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_HCD=m +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_SERIAL is not set +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_V4L1=y +CONFIG_VIDEO_V4L2_COMMON=m +CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_ZONE_DMA_FLAG=0 |