diff options
| -rw-r--r-- | target/linux/kirkwood/config-3.3 | 179 | ||||
| -rw-r--r-- | target/linux/kirkwood/patches-3.3/001-openwrt_partition_map.patch | 11 | ||||
| -rw-r--r-- | target/linux/kirkwood/patches-3.3/002-mvsdio_delay.patch | 32 | ||||
| -rw-r--r-- | target/linux/kirkwood/patches-3.3/200-iconnect.patch | 218 |
4 files changed, 440 insertions, 0 deletions
diff --git a/target/linux/kirkwood/config-3.3 b/target/linux/kirkwood/config-3.3 new file mode 100644 index 0000000000..3d29548d62 --- /dev/null +++ b/target/linux/kirkwood/config-3.3 @@ -0,0 +1,179 @@ +CONFIG_ALIGNMENT_TRAP=y +CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y +CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y +CONFIG_ARCH_KIRKWOOD=y +CONFIG_ARCH_NR_GPIO=0 +# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_ARCH_USES_GETTIMEOFFSET is not set +CONFIG_ARM=y +# CONFIG_ARM_CPU_SUSPEND is not set +CONFIG_ARM_L1_CACHE_SHIFT=5 +CONFIG_ARM_NR_BANKS=8 +CONFIG_ARM_PATCH_PHYS_VIRT=y +# CONFIG_ARM_THUMB is not set +# CONFIG_ARPD is not set +CONFIG_BCMA_POSSIBLE=y +CONFIG_BLK_DEV_SD=y +CONFIG_CACHE_FEROCEON_L2=y +# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set +# CONFIG_CACHE_L2X0 is not set +CONFIG_CLKSRC_MMIO=y +CONFIG_CMDLINE="rootdelay=1 root=/dev/mmcblk0p1 noinitrd console=ttyS0,115200" +CONFIG_CMDLINE_FROM_BOOTLOADER=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5T=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_FEROCEON=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y +CONFIG_CPU_FEROCEON=y +# CONFIG_CPU_FEROCEON_OLD_ID is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +CONFIG_CPU_IDLE=y +CONFIG_CPU_IDLE_GOV_LADDER=y +CONFIG_CPU_PABRT_LEGACY=y +CONFIG_CPU_PM=y +CONFIG_CPU_TLB_FEROCEON=y +CONFIG_CPU_USE_DOMAINS=y +CONFIG_CRC16=y +# CONFIG_DEBUG_USER is not set +CONFIG_DECOMPRESS_LZMA=y +# CONFIG_DLCI is not set +CONFIG_DNOTIFY=y +CONFIG_EXT4_FS=y +CONFIG_FRAME_POINTER=y +CONFIG_FS_MBCACHE=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_GENERIC_CPU_DEVICES is not set +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GPIOLIB=y +# CONFIG_HAMRADIO is not set +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAVE_AOUT=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_PFN_VALID=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DMA_API_DEBUG=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_HAVE_GENERIC_HARDIRQS=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_IRQ_WORK=y +CONFIG_HAVE_KERNEL_GZIP=y +CONFIG_HAVE_KERNEL_LZMA=y +CONFIG_HAVE_KERNEL_LZO=y +CONFIG_HAVE_KERNEL_XZ=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_HAVE_MEMBLOCK=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_PROC_CPU=y +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y +CONFIG_HAVE_SCHED_CLOCK=y +CONFIG_HAVE_SPARSE_IRQ=y +CONFIG_HW_RANDOM=y +CONFIG_INET_LRO=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +CONFIG_JBD2=y +CONFIG_KTIME_SCALAR=y +CONFIG_LEDS_GPIO=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_MACH_D2NET_V2 is not set +# CONFIG_MACH_DB88F6281_BP is not set +CONFIG_MACH_DOCKSTAR=y +# CONFIG_MACH_ESATA_SHEEVAPLUG is not set +# CONFIG_MACH_GURUPLUG is not set +CONFIG_MACH_ICONNECT=y +# CONFIG_MACH_INETSPACE_V2 is not set +# CONFIG_MACH_MV88F6281GTW_GE is not set +# CONFIG_MACH_NET2BIG_V2 is not set +# CONFIG_MACH_NET5BIG_V2 is not set +# CONFIG_MACH_NETSPACE_MAX_V2 is not set +# CONFIG_MACH_NETSPACE_V2 is not set +CONFIG_MACH_OPENRD=y +CONFIG_MACH_OPENRD_BASE=y +CONFIG_MACH_OPENRD_CLIENT=y +# CONFIG_MACH_OPENRD_ULTIMATE is not set +# CONFIG_MACH_RD88F6192_NAS is not set +# CONFIG_MACH_RD88F6281 is not set +CONFIG_MACH_SHEEVAPLUG=y +# CONFIG_MACH_T5325 is not set +# CONFIG_MACH_TS219 is not set +# CONFIG_MACH_TS41X is not set +CONFIG_MDIO_BOARDINFO=y +# CONFIG_MLX4_CORE is not set +CONFIG_MMC=y +CONFIG_MMC_BLOCK=y +CONFIG_MMC_MVSDIO=y +# CONFIG_MMC_TIFM_SD is not set +# CONFIG_MTD_CFI is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ECC=y +CONFIG_MTD_NAND_ORION=y +# CONFIG_MTD_ROOTFS_ROOT_DEV is not set +# CONFIG_MTD_ROOTFS_SPLIT is not set +# CONFIG_MTD_SM_COMMON is not set +CONFIG_MV643XX_ETH=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_PER_CPU_KM=y +CONFIG_NET_DSA=y +# CONFIG_NET_DSA_MV88E6060 is not set +CONFIG_NET_DSA_MV88E6131=y +CONFIG_NET_DSA_MV88E6XXX=y +CONFIG_NET_DSA_MV88E6XXX_NEED_PPU=y +CONFIG_NET_DSA_TAG_DSA=y +# CONFIG_NET_DSA_TAG_TRAILER is not set +CONFIG_NLS=y +CONFIG_OUTER_CACHE=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PCI=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PHYLIB=y +CONFIG_PLAT_ORION=y +# CONFIG_PREEMPT_RCU is not set +# CONFIG_QUOTACTL is not set +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_MV=y +CONFIG_SCSI=y +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SDIO_UART is not set +CONFIG_SPLIT_PTLOCK_CPUS=999999 +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_UID16=y +CONFIG_USB=y +CONFIG_USB_ARCH_HAS_XHCI=y +CONFIG_USB_COMMON=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_STORAGE=y +CONFIG_USB_SUPPORT=y +# CONFIG_USB_UHCI_HCD is not set +CONFIG_VECTORS_BASE=0xffff0000 +# CONFIG_VFP is not set +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_WAN=y +CONFIG_XZ_DEC=y +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/kirkwood/patches-3.3/001-openwrt_partition_map.patch b/target/linux/kirkwood/patches-3.3/001-openwrt_partition_map.patch new file mode 100644 index 0000000000..0f94adc343 --- /dev/null +++ b/target/linux/kirkwood/patches-3.3/001-openwrt_partition_map.patch @@ -0,0 +1,11 @@ +--- a/arch/arm/mach-kirkwood/sheevaplug-setup.c ++++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c +@@ -33,7 +33,7 @@ static struct mtd_partition sheevaplug_n + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_4M + }, { +- .name = "root", ++ .name = "rootfs", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, diff --git a/target/linux/kirkwood/patches-3.3/002-mvsdio_delay.patch b/target/linux/kirkwood/patches-3.3/002-mvsdio_delay.patch new file mode 100644 index 0000000000..46e2a5646c --- /dev/null +++ b/target/linux/kirkwood/patches-3.3/002-mvsdio_delay.patch @@ -0,0 +1,32 @@ +--- a/drivers/mmc/core/sd.c ++++ b/drivers/mmc/core/sd.c +@@ -389,6 +389,15 @@ int mmc_sd_switch_hs(struct mmc_card *ca + return -ENOMEM; + } + ++ /* ++ * Some SDHC cards, notably those with a Sandisk SD controller ++ * (also found in Kingston products) need a bit of slack ++ * before successfully handling the SWITCH command. So far, ++ * cards identifying themselves as "SD04G" and "SD08G" are ++ * affected ++ */ ++ udelay(1000); ++ + err = mmc_sd_switch(card, 1, 0, 1, status); + if (err) + goto out; +--- a/drivers/mmc/core/core.c ++++ b/drivers/mmc/core/core.c +@@ -529,9 +529,9 @@ void mmc_set_data_timeout(struct mmc_dat + * The limit is really 250 ms, but that is + * insufficient for some crappy cards. + */ +- limit_us = 300000; ++ limit_us = 500000; + else +- limit_us = 100000; ++ limit_us = 200000; + + /* + * SDHC cards always use these fixed values. diff --git a/target/linux/kirkwood/patches-3.3/200-iconnect.patch b/target/linux/kirkwood/patches-3.3/200-iconnect.patch new file mode 100644 index 0000000000..5a46ee780f --- /dev/null +++ b/target/linux/kirkwood/patches-3.3/200-iconnect.patch @@ -0,0 +1,218 @@ +--- a/arch/arm/mach-kirkwood/Makefile ++++ b/arch/arm/mach-kirkwood/Makefile +@@ -8,6 +8,7 @@ obj-$(CONFIG_MACH_SHEEVAPLUG) += sheeva + obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o + obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o + obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o ++obj-$(CONFIG_MACH_ICONNECT) += iconnect-setup.o + obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o + obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o + obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o +--- a/arch/arm/mach-kirkwood/Kconfig ++++ b/arch/arm/mach-kirkwood/Kconfig +@@ -130,6 +130,12 @@ config MACH_T5325 + Say 'Y' here if you want your kernel to support the + HP t5325 Thin Client. + ++config MACH_ICONNECT ++ bool "Iomega iConnect Wireless" ++ help ++ Say 'Y' here if you want your kernel to support the ++ Iomega iConnect Wireless. ++ + endmenu + + endif +--- /dev/null ++++ b/arch/arm/mach-kirkwood/iconnect-setup.c +@@ -0,0 +1,190 @@ ++/* ++ * arch/arm/mach-kirkwood/iconnect-setup.c ++ * ++ * Iomega iConnect Wireless ++ * ++ * This file is licensed under the terms of the GNU General Public ++ * License version 2. This program is licensed "as is" without any ++ * warranty of any kind, whether express or implied. ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/platform_device.h> ++#include <linux/irq.h> ++#include <linux/mtd/partitions.h> ++#include <linux/mv643xx_eth.h> ++#include <linux/ethtool.h> ++#include <linux/gpio.h> ++#include <linux/gpio_keys.h> ++#include <linux/input.h> ++#include <linux/leds.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <mach/kirkwood.h> ++#include "common.h" ++#include "mpp.h" ++ ++static struct mtd_partition iconnect_nand_parts[] = { ++ { ++ .name = "u-boot", ++ .offset = 0, ++ .size = SZ_1M ++ }, { ++ .name = "uImage", ++ .offset = MTDPART_OFS_NXTBLK, ++ .size = SZ_1M + SZ_2M ++ }, { ++ .name = "rootfs", ++ .offset = MTDPART_OFS_NXTBLK, ++ .size = SZ_32M, ++ }, { ++ .name = "data", ++ .offset = MTDPART_OFS_NXTBLK, ++ .size = MTDPART_SIZ_FULL ++ }, ++}; ++ ++static struct mv643xx_eth_platform_data iconnect_ge00_data = { ++ .phy_addr = MV643XX_ETH_PHY_ADDR(11), ++}; ++ ++static struct gpio_led iconnect_led_pins[] = { ++ { ++ .name = "iconnect:blue:power", ++ .default_trigger = "default-on", ++ .gpio = 42, ++ }, ++ { ++ .name = "iconnect:red:power", ++ .gpio = 43, ++ }, ++ { ++ .name = "iconnect:blue:usb1", ++ .gpio = 44, ++ }, ++ { ++ .name = "iconnect:blue:usb2", ++ .gpio = 45, ++ }, ++ { ++ .name = "iconnect:blue:usb3", ++ .gpio = 46, ++ }, ++ { ++ .name = "iconnect:blue:usb4", ++ .gpio = 47, ++ }, ++ { ++ .name = "iconnect:blue:otb", ++ .gpio = 48, ++ }, ++}; ++ ++static struct gpio_led_platform_data iconnect_led_data = { ++ .leds = iconnect_led_pins, ++ .num_leds = ARRAY_SIZE(iconnect_led_pins), ++}; ++ ++static struct platform_device iconnect_leds = { ++ .name = "leds-gpio", ++ .id = -1, ++ .dev = { ++ .platform_data = &iconnect_led_data, ++ } ++}; ++ ++#define ICONNECT_GPIO_KEY_RESET 12 ++#define ICONNECT_GPIO_KEY_OTB 35 ++ ++#define ICONNECT_SW_RESET 0x00 ++#define ICONNECT_SW_OTB 0x01 ++ ++static struct gpio_keys_button iconnect_buttons[] = { ++ { ++ .type = EV_SW, ++ .code = ICONNECT_SW_RESET, ++ .gpio = ICONNECT_GPIO_KEY_RESET, ++ .desc = "Reset Button", ++ .active_low = 1, ++ .debounce_interval = 100, ++ }, ++ { ++ .type = EV_SW, ++ .code = ICONNECT_SW_OTB, ++ .gpio = ICONNECT_GPIO_KEY_OTB, ++ .desc = "OTB Button", ++ .active_low = 1, ++ .debounce_interval = 100, ++ }, ++}; ++ ++static struct gpio_keys_platform_data iconnect_button_data = { ++ .buttons = iconnect_buttons, ++ .nbuttons = ARRAY_SIZE(iconnect_buttons), ++}; ++ ++static struct platform_device iconnect_button_device = { ++ .name = "gpio-keys", ++ .id = -1, ++ .num_resources = 0, ++ .dev = { ++ .platform_data = &iconnect_button_data, ++ }, ++}; ++ ++static unsigned int iconnect_mpp_config[] __initdata = { ++ MPP12_GPIO, /*Input for reset button*/ ++ MPP35_GPIO, /*Input for OTB button*/ ++ MPP42_GPIO, ++ MPP43_GPIO, ++ MPP44_GPIO, ++ MPP45_GPIO, ++ MPP46_GPIO, ++ MPP47_GPIO, ++ MPP48_GPIO, ++ 0 ++}; ++ ++static void __init iconnect_init(void) ++{ ++ u32 dev, rev; ++ ++ /* ++ * Basic setup. Needs to be called early. ++ */ ++ kirkwood_init(); ++ kirkwood_mpp_conf(iconnect_mpp_config); ++ ++ kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25); ++ kirkwood_ehci_init(); ++ ++ kirkwood_ge00_init(&iconnect_ge00_data); ++ kirkwood_pcie_id(&dev, &rev); ++ ++ kirkwood_uart0_init(); ++ kirkwood_i2c_init(); ++ ++ platform_device_register(&iconnect_leds); ++ platform_device_register(&iconnect_button_device); ++} ++ ++static int __init iconnect_pci_init(void) ++{ ++ if (machine_is_iconnect()) ++ kirkwood_pcie_init(KW_PCIE0); ++ ++ return 0; ++} ++subsys_initcall(iconnect_pci_init); ++ ++ ++MACHINE_START(ICONNECT, "Iomega iConnect Wireless") ++ .atag_offset = 0x100, ++ .init_machine = iconnect_init, ++ .map_io = kirkwood_map_io, ++ .init_early = kirkwood_init_early, ++ .init_irq = kirkwood_init_irq, ++ .timer = &kirkwood_timer, ++ .restart = kirkwood_restart, ++MACHINE_END |