x86: add support for 3.10

Add kernel configuration and patches for Linux 3.10.

Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.

Russell says in the original patch:

"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built.  The patches
required no changes."

The current patch contains additional configuration tweaks,
and the kernel patches were refreshed.

Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37867 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 176 insertions, 0 deletions

diff --git a/target/linux/x86/patches-3.10/010-rdc_cpu_ident.patch b/target/linux/x86/patches-3.10/010-rdc_cpu_ident.patch
new file mode 100644
index 0000000000..6f3eab3242
--- /dev/null
+++ b/target/linux/x86/patches-3.10/010-rdc_cpu_ident.patch
@@ -0,0 +1,176 @@
+--- /dev/null
++++ b/Documentation/x86/rdc.txt
+@@ -0,0 +1,69 @@
++
++Introduction
++============
++
++RDC (http://www.rdc.com.tw) have been manufacturing x86-compatible SoC
++(system-on-chips) for a number of years.  They are not the fastest of
++CPUs (clock speeds ranging from 133-150MHz) but 486SX compatibility
++coupled with very low power consumption[1] and low cost make them ideal
++for embedded applications.
++
++
++Where to find
++=============
++
++RDC chips show up in numerous embedded devices, but be careful since
++many of them will not run Linux 2.6 without significant expertise.
++
++There are several variants of what the linux kernel refers to generically
++as RDC321X:  R8610, R321x, S3282 and AMRISC20000.
++
++R321x: Found in various routers, see the OpenWrt project for details,
++   http://wiki.openwrt.org/oldwiki/rdcport
++
++R8610: Found on the RDC evaluation board
++   http://www.ivankuten.com/system-on-chip-soc/rdc-r8610/
++
++AMRISC20000: Found in the MGB-100 wireless hard disk
++   http://tintuc.no-ip.com/linux/tipps/mgb100/
++
++S3282: Found in various NAS devices, including the Bifferboard
++   http://www.bifferos.com
++
++
++Kernel Configuration
++====================
++
++Add support for this CPU with CONFIG_X86_RDC321X.  Ensure that maths
++emulation is included (CONFIG_MATH_EMULATION selected) and avoid MCE
++(CONFIG_X86_MCE not selected).
++
++
++CPU detection
++=============
++
++None of these chips support the cpuid instruction, so as with some
++other x86 compatible SoCs, we must check the north bridge and look
++for specific 'signature' PCI device config.
++
++The current detection code has been tested only on the Bifferboard
++(S3282 CPU), please send bug reports or success stories with
++other devices to bifferos@yahoo.co.uk.
++
++
++Credits
++=======
++
++Many thanks to RDC for providing the customer codes to allow
++detection of all known variants, without which this detection code
++would have been very hard to ascertain.
++
++
++References
++==========
++
++[1] S3282 in certain NAS solutions consumes less than 1W
++
++
++mark@bifferos.com 2009
++
+--- a/arch/x86/Kconfig
++++ b/arch/x86/Kconfig
+@@ -481,6 +481,7 @@ config X86_RDC321X
+ 	bool "RDC R-321x SoC"
+ 	depends on X86_32
+ 	depends on X86_EXTENDED_PLATFORM
++	select PCI
+ 	select M486
+ 	select X86_REBOOTFIXUPS
+ 	select EMBEDDED
+--- a/arch/x86/include/asm/processor.h
++++ b/arch/x86/include/asm/processor.h
+@@ -137,7 +137,8 @@ struct cpuinfo_x86 {
+ #define X86_VENDOR_CENTAUR	5
+ #define X86_VENDOR_TRANSMETA	7
+ #define X86_VENDOR_NSC		8
+-#define X86_VENDOR_NUM		9
++#define X86_VENDOR_RDC		9
++#define X86_VENDOR_NUM		10
+ 
+ #define X86_VENDOR_UNKNOWN	0xff
+ 
+--- a/arch/x86/kernel/cpu/Makefile
++++ b/arch/x86/kernel/cpu/Makefile
+@@ -26,6 +26,7 @@ obj-$(CONFIG_CPU_SUP_CYRIX_32)		+= cyrix
+ obj-$(CONFIG_CPU_SUP_CENTAUR)		+= centaur.o
+ obj-$(CONFIG_CPU_SUP_TRANSMETA_32)	+= transmeta.o
+ obj-$(CONFIG_CPU_SUP_UMC_32)		+= umc.o
++obj-$(CONFIG_X86_RDC321X)		+= rdc.o
+ 
+ obj-$(CONFIG_PERF_EVENTS)		+= perf_event.o
+ 
+--- /dev/null
++++ b/arch/x86/kernel/cpu/rdc.c
+@@ -0,0 +1,69 @@
++/*
++ * See Documentation/x86/rdc.txt
++ *
++ * mark@bifferos.com
++ */
++
++#include <linux/pci.h>
++#include <asm/pci-direct.h>
++#include "cpu.h"
++
++
++static void __cpuinit rdc_identify(struct cpuinfo_x86 *c)
++{
++	u16 vendor, device;
++	u32 customer_id;
++
++	if (!early_pci_allowed())
++		return;
++
++	/* RDC CPU is SoC (system-on-chip), Northbridge is always present */
++	vendor = read_pci_config_16(0, 0, 0, PCI_VENDOR_ID);
++	device = read_pci_config_16(0, 0, 0, PCI_DEVICE_ID);
++
++	if (vendor != PCI_VENDOR_ID_RDC || device != PCI_DEVICE_ID_RDC_R6020)
++		return;  /* not RDC */
++	/*
++	 * NB: We could go on and check other devices, e.g. r6040 NIC, but
++	 * that's probably overkill
++	 */
++
++	customer_id = read_pci_config(0, 0, 0, 0x90);
++
++	switch (customer_id) {
++		/* id names are from RDC */
++	case 0x00321000:
++		strcpy(c->x86_model_id, "R3210/R3211");
++		break;
++	case 0x00321001:
++		strcpy(c->x86_model_id, "AMITRISC20000/20010");
++		break;
++	case 0x00321002:
++		strcpy(c->x86_model_id, "R3210X/Edimax");
++		break;
++	case 0x00321003:
++		strcpy(c->x86_model_id, "R3210/Kcodes");
++		break;
++	case 0x00321004:  /* tested */
++		strcpy(c->x86_model_id, "S3282/CodeTek");
++		break;
++	case 0x00321007:
++		strcpy(c->x86_model_id, "R8610");
++		break;
++	default:
++		pr_info("RDC CPU: Unrecognised Customer ID (0x%x) please report to linux-kernel@vger.kernel.org\n", customer_id);
++		break;
++	}
++
++	strcpy(c->x86_vendor_id, "RDC");
++	c->x86_vendor = X86_VENDOR_RDC;
++}
++
++static const struct cpu_dev __cpuinitconst rdc_cpu_dev = {
++	.c_vendor	= "RDC",
++	.c_ident	= { "RDC" },
++	.c_identify	= rdc_identify,
++	.c_x86_vendor	= X86_VENDOR_RDC,
++};
++
++cpu_dev_register(rdc_cpu_dev);