jogo [Thu, 5 Sep 2013 20:30:34 +0000 (20:30 +0000)]
kernel: b53: support phy ids for BCM5365
BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.
Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37906 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the following error:
rtl_pci: Unknown symbol rtl_lps_leave (err 0)
rtl_pci: Unknown symbol rtl_lps_enter (err 0)
rtl8192ce: Unknown symbol rtl_pci_disconnect (err 0)
rtl8192ce: Unknown symbol rtl_pci_probe (err 0)
rtl8192de: Unknown symbol rtl_pci_disconnect (err 0)
rtl8192de: Unknown symbol rtl_pci_probe (err 0)
rtl8192se: Unknown symbol rtl_pci_disconnect (err 0)
rtl8192se: Unknown symbol rtl_pci_probe (err 0)
This enables usage of the ath10k driver on OpenWrt. Only 2.0 PCI hardware
is supported. The ath10k firmware is currently only available
through github so use that as its source for now.
This goes build tested, not run time tested.
[Hauke: I did some minor changes]
Cc: ath10k@lists.infradead.org Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Kathy Giori <kgiori@qca.qualcomm.com> Cc: Mathieu Olivari <mathieu@qca.qualcomm.com> Cc: Jerome Proffit <jproffit@qca.qualcomm.com> Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com> Cc: Matthew McClintock <mmcclint@qca.qualcomm.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37898 3c298f89-4303-0410-b956-a3cf2f4a3e73
kernel: b53: allow access the MIB counters on BCM5365
b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.
Users may have merge.ff set to false, which will force merge commits to
be generated. The intent here is to have a fast-forward merge when
possible, so let's make sure fast-forwards are enabled.
Looking at the target 'defconfig' in include/toplevel, it doesn't
directly reference $(HOME)/.openwrt/defconfig nor does it reference any
prerequisites using it as a target.
Therefore, building "defconfig" as a target uses the defaults in the
tree, but not the defaults that a user might have explicitly specified.
This patch fixes this regression from r36361.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
[florian: apply with the proper patch level, wrap at 80 columns] Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37883 3c298f89-4303-0410-b956-a3cf2f4a3e73
generic: remove linux version checks from myloader.c
The myloader partition parser code uses ifdef wrappers
to make the code usable on kernels below version 3.2.
All targets are using kernel 3.3 at least so the wraper
is not needed. Remove that.
ar71xx: configure OBS4 line on TL-WR841N-v8/MR3420v2
It also fixes USB Power on MR3420v2.
This time we took the information from the source of GPL:
http://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg18970.html
Confirmed and tested:
https://dev.openwrt.org/ticket/13201#comment:41
Thanks to oguretsagressive for testing.
The package makes it possible to create custom SPI
buses via GPIO lines.
This module is based on i2c-gpio-custom and allows to
configure an SPI bus via GPIO lines and expose it to
userspace without rebuilding the kernel. This is maily
intended to connect microcontrollers and other simple
SPI devices without making an ad-hoc kernel driver.
Signed-off-by: Marco Burato <zmaster.adsl@gmail.com>
[juhosg:
- change subject,
- extend and reformat commit message,
- cleanup checkpatch errors/warnings in module source] Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37872 3c298f89-4303-0410-b956-a3cf2f4a3e73
ar71xx: fix initramfs image generation for Cameo933x profiles
Initramfs images are not generated for profiles which
are using the squashfs-only template. Add the missing
'Image/Build/Template/squashfs-only/initramfs' to fix
that.
Also, 'Image/Build/Cameo933x/initramfs' uses wrong
parameters for 'MkuImageLzma/initramfs' due to a
misplaced commma. Remove that to fix the generated
initramfs images.
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
The current patch contains additional configuration tweaks.
Add kernel configuration and patches for Linux 3.10.
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
The current patch contains additional configuration tweaks,
and the kernel patches were refreshed.
juhosg [Tue, 27 Aug 2013 12:02:58 +0000 (12:02 +0000)]
image: ensure that /dev/console exist in rootfs images
Linux expects that the /dev/console node is present in
the rootfs image. Create the node in rootfs images, in
order to make std{in,out,err} usable even in early init
process.
Note: tar.gz and cpio.gz images are not handled yet.
juhosg [Tue, 27 Aug 2013 12:02:54 +0000 (12:02 +0000)]
kernel: ensure that /dev/console exists in initramfs
Linux expects that the /dev/console node is present
in the rootfs image. Create the node in initramfs,
in order to make std{in,out,err} usable even in early
init process.
juhosg [Tue, 27 Aug 2013 10:48:24 +0000 (10:48 +0000)]
ar71xx: don't register USB device on WNDAP360
Apparently registering usb device on newest trunk causes
this AP not to boot...
Since there is no USB socket in that device anyway this
can be simply removed (and device boots then no problem).
[juhosg:
- tweak subject line and description,
- remove #include "dev-usb.h",
- remove 'select ATH79_DEV_USB' from Kconfig]
nbd [Mon, 26 Aug 2013 17:31:27 +0000 (17:31 +0000)]
mklibs: Fix mklibs usage when *.so files reside in subdirs
Currently package/Makefile only passes /lib /usr/lib and /usr/lib/ebtables
to mklibs. However, other libs can also reside in different subdirectories
(in my case /usr/lib/ipsec). Hence, create the list of library directories
dynamically.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37841 3c298f89-4303-0410-b956-a3cf2f4a3e73
juhosg [Fri, 23 Aug 2013 17:07:25 +0000 (17:07 +0000)]
ramips: update the RT3883 PCI patch
Fix the following warning:
arch/mips/pci/pci-rt3883.c: In function 'rt3883_pci_probe':
arch/mips/pci/pci-rt3883.c:458:4: warning: use of 'h' length modifier with 'a' type character [-Wformat]
Signed-off-by: Michael Lee <igvtee@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37827 3c298f89-4303-0410-b956-a3cf2f4a3e73
juhosg [Fri, 23 Aug 2013 17:07:20 +0000 (17:07 +0000)]
kernel/3.10: backport of_pci_get_devfn function from 3.11
Fixes the following build error on ramips/rt3883:
arch/mips/pci/pci-rt3883.c:488:3: error: implicit declaration of function \
'of_pci_get_devfn' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Although the function is only used by the PCI driver
of the RT3883 SoC but at the moment but it might be
useful for other targets as well.
Signed-off-by: Michael Lee <igvtee@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37826 3c298f89-4303-0410-b956-a3cf2f4a3e73
nbd [Wed, 21 Aug 2013 20:59:25 +0000 (20:59 +0000)]
kernel: crashlog: Avoid out-of-bounds write
vsnprintf returns the number of chars that would have been written, not
the actual number of chars written. This can lead to crashlog_buf->len
being too big which in turn can lead to get_maxlen() returning negative
numbers. The length argument of kmsg_dump_get_buffer will be casted to
a size_t which makes a negative input a big positive number allowing
kmsg_dump_get_buffer to write out of bounds.
Fix this by using vscnprintf which returns the actually written number
of chars.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37820 3c298f89-4303-0410-b956-a3cf2f4a3e73