nbd [Wed, 10 Oct 2012 11:38:58 +0000 (11:38 +0000)]
cns3xxx: Fix laguna arm11mpcore watchdog
The ARM11MPCore Timer/Watchdog registers start at offset 0x600 which is where
all mpcore-wdt boards point the driver base too. I believe this is wrong
because 0x600 is aliased to the timer/watchdog of the 'current CPU' where
0x700 is CPU0's timer/watchdog, and 0x800 is CPU1's timer/watchdog. Thus
if your timer/watchdog application is switching between CPU's it can end up
writing to the wrong CPU's registers which results in random board resets
from watchdog timeouts etc.
This patch forces the timer/watchdog driver to use CPU0's registers always.
Its my opinion that other mpcore-wdt boards should be doing the same thing.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33683 3c298f89-4303-0410-b956-a3cf2f4a3e73
nbd [Wed, 10 Oct 2012 11:38:44 +0000 (11:38 +0000)]
mtd: allow partial block unlock
This allows sysupgrade for devices such as the Gateworks Avila/Cambria
product families based on the ixp4xx using the redboot bootloader with
combined FIS directory and RedBoot config partitions on larger FLASH
devices with larger eraseblocks.
This second iteration of this patch addresses previous issues:
- whitespace breakage fixed
- unlock in all scenarios
- simplification and fix logic bug
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33681 3c298f89-4303-0410-b956-a3cf2f4a3e73
nbd [Wed, 10 Oct 2012 11:38:36 +0000 (11:38 +0000)]
ixp4xx-microcode: Add ixp4xx NPE-A-HSS firmware
The ixp4xx HSS firmware is needed in order to use the HSS (synchronous serial
port). An example of where this is used is the Gateworks Avila boards to
interface to an audio codec.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33680 3c298f89-4303-0410-b956-a3cf2f4a3e73
jow [Tue, 9 Oct 2012 16:41:36 +0000 (16:41 +0000)]
[package] cyassl: add a patch to better check legacy SSLv2 client hello records
If junk data is received during SSL_accept(), cyassl will treat it as legacy SSLv2
record without performing further plausibility checks. Change the legacy code path
to return UNKNOWN_HANDSHAKE_TYPE if the value of the third byte isn't 0x01 the
hello message type.
hauke [Mon, 8 Oct 2012 20:18:27 +0000 (20:18 +0000)]
mac80211: brcmsmac: use firmware extracted from proprietary driver
The firmware from linux-firmware does not support the rev 17 core found
in a bcm4716. The firmware extracted from the proprietary driver
supports this core. Use this firmware instead by default.
nbd [Sun, 7 Oct 2012 23:23:47 +0000 (23:23 +0000)]
ixp4xx: update Gateworks Avila board support
Several new features for newer boards:
- add additional UARTs present on some boards
- add additional LEDs present on some boards
- add HSS audio device codec present on some boards
- add support for GSC present on some boards
- add per model setup support for newer boards
- set FLASH window per-model for boards with larger FLASH
Some fixes:
- add IRQ mapping for additional PCI devices (USB Host)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33647 3c298f89-4303-0410-b956-a3cf2f4a3e73
nbd [Sun, 7 Oct 2012 23:23:34 +0000 (23:23 +0000)]
ixp4xx: update Gateworks Cambria board support
Several new features for newer boards:
- add irq mapping for additional devices
- add platform data for i2c bus to SFP modules
- add additional UARTs present on some boards
- increased R/W delay for expansion bus UARTs
- add additional LEDs present on some boards
- add GPIO exports and configuration
- add ENET switch config present on some boards
- add support for GSC present on some boards
- added per model setup support for newer boards
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33644 3c298f89-4303-0410-b956-a3cf2f4a3e73
hauke [Thu, 4 Oct 2012 21:39:22 +0000 (21:39 +0000)]
[package] acx-mac80211: adapt interface changes in mac80211
The prototype of conf_tx and tx in struct ieee80211_ops changed some
time ago and was not compatible with the prototype assumes by
acs-mac80211.
At least I do not see any compile warnings about this any more.
hauke [Thu, 4 Oct 2012 15:45:54 +0000 (15:45 +0000)]
[brcm47xx]: bcma: do not initialize deactivated PCIe cores
Before it was tried to initialize the deactivated PCIe core in client
mode, but this causes the SoC to hang. Just do not initialize it at all
and ignore the core it is not working and nothing is connected to it
when the specific bit is set in the boardflags.
juhosg [Thu, 4 Oct 2012 06:34:14 +0000 (06:34 +0000)]
mac80211/rt2x00: fix lna assignment typo in Rt3352 which went upstream
Reviewing what went into wireless-testing I found a quite nasty mistake,
probably a result of copy&past'ing from the lines below in rt2800lib.c.
This adds another patch to fix that.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33616 3c298f89-4303-0410-b956-a3cf2f4a3e73
juhosg [Thu, 4 Oct 2012 06:34:12 +0000 (06:34 +0000)]
mac80211/rt2x00: sync Rt3352 support
The original patch was accepted into linux-next in a slightly modified form.
In order to provide integrity to follow-up patches, replace the patch in OpenWrt
with the (semantically identical) now upstream patch.
(commit 03839951515b0ea2b21d649b1fe7b63f9817d0c8 in wireless-testing)
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33615 3c298f89-4303-0410-b956-a3cf2f4a3e73
juhosg [Thu, 4 Oct 2012 06:34:09 +0000 (06:34 +0000)]
ramips: add image for ALL0256N-8M
The new version of the ALL0256N now got 8MB SPI NOR flash instead of 4MB.
In order to expose the whole amount of flash, add another image which contains
the corresponding GENERIC_8M mtdparts.
[brcm47xx]: bcma: use fallback sprom if sprom on card was not valid
Sometimes the PCIe card indicates that it has a sprom somewhere and we
are able to read the memory region, but it is empty and not valid. In
these cases we should try to use the fallback sprom as a last chance.
The chip common and the PCIe code are accessing the sprom struct which
is not filled when these cores are initialized. Fix this by adding an
early initialize and fill the sprom struct before accessing it in other
code.
[brcm47xx]: Fix reading sprom from nvram without a prefix
The bcma based SoCs with a ieee80211 core on the SoC and an other
connected via PCIe or USB store the sprom for the SoC with a sb/1/
prefix. The SoC with just one wifi core do not use prefixes. The
BCM4706 do not use a prefix for the SoC part at all, because the prefix
is the path to the ieee80211 core and there is non on the BCM4706.