--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -321,6 +321,63 @@ static struct board_info __initdata boar
+@@ -831,6 +831,63 @@ static struct board_info __initdata boar
+ },
},
};
-
-+ static struct board_info __initdata board_V2500V_BB = {
-+ .name = "V2500V_BB",
++
++static struct board_info __initdata board_V2500V_BB = {
++ .name = "V2500V_BB",
+ .expected_cpu_id = 0x6348,
+
+ .has_uart0 = 1,
+ .enet1 = {
+ .force_speed_100 = 1,
+ .force_duplex_full = 1,
-+ },
++ },
+
-+ .leds = {
++ .leds = {
+ {
-+ .name = "power:green",
++ .name = "V2500V_BB:green:power",
+ .gpio = 0,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
-+ .name = "power:red",
++ .name = "V2500V_BB:red:power",
+ .gpio = 1,
+ .active_low = 1,
+ },
+ {
-+ .name = "adsl",
++ .name = "V2500V_BB:green:adsl",
+ .gpio = 2,
+ .active_low = 1,
+ },
-+ { .name = "ppp",
++ { .name = "V2500V_BB:green:ppp",
+ .gpio = 3,
+ .active_low = 1,
+ },
+ {
-+ .name = "wireless",
++ .name = "V2500V_BB:green:wireless",
+ .gpio = 6,
+ .active_low = 1,
+ },
+ },
+ },
+};
-+
#endif
/*
-@@ -1787,6 +1844,7 @@ static const struct board_info __initdat
+@@ -1782,6 +1839,7 @@ static const struct board_info __initdat
&board_96348_D4PW,
&board_spw500v,
&board_96348sv,
#endif
#ifdef CONFIG_BCM63XX_CPU_6358
-@@ -1940,6 +1998,22 @@ void __init board_prom_init(void)
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- val &= MPI_CSBASE_BASE_MASK;
+@@ -1908,6 +1966,23 @@ void __init board_prom_init(void)
+ val &= MPI_CSBASE_BASE_MASK;
+ }
boot_addr = (u8 *)KSEG1ADDR(val);
+ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
+
+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
+ /* Do an early check of CFE and then select bank 0 */
+
-+ if (boot_addr == (u8 *)0xbf800000) {
++ if (boot_addr == (u8 *)0xbf800000) {
++ unsigned char board_name[16];
+ u8 *tmp_boot_addr;
+ tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
-+ memcpy(&nvram, tmp_boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
-+ if (!strcmp(nvram.name, "V2500V_BB")) {
++ memcpy(board_name, tmp_boot_addr + BCM963XX_NVRAM_OFFSET + offsetof(struct bcm963xx_nvram, name), sizeof(board_name));
++ if (!strcmp(board_name, "V2500V_BB")) {
+ printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
+ boot_addr = (u8 *)0xbfc00000; // Bank 0
+ }
/* dump cfe version */
cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
-@@ -2161,6 +2235,13 @@ int __init board_register_devices(void)
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- val &= MPI_CSBASE_BASE_MASK;
+--- a/arch/mips/bcm63xx/dev-flash.c
++++ b/arch/mips/bcm63xx/dev-flash.c
+@@ -18,6 +18,7 @@
+ #include <linux/spi/spi.h>
+ #include <linux/spi/flash.h>
-+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+ /* Loading from CFE always uses Bank 0 */
-+ if (!strcmp(board.name, "V2500V_BB")) {
-+ printk(KERN_INFO PFX "V2500V: Start in Bank 0\n");
-+ val = val + 0x400000; // Select Bank 0 start address
-+ }
++#include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+ #include <bcm63xx_dev_flash.h>
+ #include <bcm63xx_dev_hsspi.h>
+@@ -145,6 +146,13 @@ int __init bcm63xx_flash_register(int nu
+ val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+ val &= MPI_CSBASE_BASE_MASK;
+
++ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
++ /* Loading from CFE always uses Bank 0 */
++ if (!strcmp(board_get_name(), "V2500V_BB")) {
++ pr_info("V2500V: Start in Bank 0\n");
++ val = val + 0x400000; // Select Bank 0 start address
++ }
+
- mtd_resources[0].start = val;
- mtd_resources[0].end = 0x1FFFFFFF;
+ mtd_resources[0].start = val;
+ mtd_resources[0].end = 0x1FFFFFFF;