#include "dev-eth.h"
#include "dev-m25p80.h"
#include "dev-nfc.h"
+#include "dev-usb.h"
#include "dev-wmac.h"
#include "machtypes.h"
#include "routerboot.h"
#define RB2011_GPIO_NAND_NCE 14
+#define RB2011_GPIO_SFP_LOS 21
#define RB_ROUTERBOOT_OFFSET 0x0000
-#define RB_ROUTERBOOT_SIZE 0xb000
-#define RB_HARD_CFG_OFFSET 0xb000
+#define RB_ROUTERBOOT_MIN_SIZE 0xb000
#define RB_HARD_CFG_SIZE 0x1000
#define RB_BIOS_OFFSET 0xd000
-#define RB_BIOS_SIZE 0x2000
+#define RB_BIOS_SIZE 0x1000
#define RB_SOFT_CFG_OFFSET 0xf000
#define RB_SOFT_CFG_SIZE 0x1000
{
.name = "routerboot",
.offset = RB_ROUTERBOOT_OFFSET,
- .size = RB_ROUTERBOOT_SIZE,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "hard_config",
- .offset = RB_HARD_CFG_OFFSET,
.size = RB_HARD_CFG_SIZE,
.mask_flags = MTD_WRITEABLE,
}, {
.mask_flags = MTD_WRITEABLE,
}, {
.name = "soft_config",
- .offset = RB_SOFT_CFG_OFFSET,
.size = RB_SOFT_CFG_SIZE,
}
};
+
+static void __init rb2011_init_partitions(void)
+{
+ u8 *addr = (u8 *) KSEG1ADDR(0x1f000000);
+ u32 next = RB_ROUTERBOOT_MIN_SIZE;
+
+ if (routerboot_find_magic(addr, 0x10000, &next, true))
+ printk(KERN_ERR "Warning: could not find a valid RouterBOOT hard config\n");
+ rb2011_spi_partitions[0].size = next;
+ rb2011_spi_partitions[1].offset = next;
+
+ next = RB_BIOS_OFFSET + RB_BIOS_SIZE;
+ if (routerboot_find_magic(addr, 0x10000, &next, false))
+ printk(KERN_ERR "Warning: could not find a valid RouterBOOT soft config\n");
+
+ rb2011_spi_partitions[3].offset = next;
+}
+
+
static struct mtd_partition rb2011_nand_partitions[] = {
{
.name = "booter",
.mode = AR8327_PAD_MAC_RGMII,
.txclk_delay_en = true,
.rxclk_delay_en = true,
- .txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
- .rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
+ .txclk_delay_sel = AR8327_CLK_DELAY_SEL3,
+ .rxclk_delay_sel = AR8327_CLK_DELAY_SEL0,
+};
+
+static struct ar8327_pad_cfg rb2011_ar8327_pad6_cfg;
+static struct ar8327_sgmii_cfg rb2011_ar8327_sgmii_cfg;
+
+static struct ar8327_led_cfg rb2011_ar8327_led_cfg = {
+ .led_ctrl0 = 0x0000c731,
+ .led_ctrl1 = 0x00000000,
+ .led_ctrl2 = 0x00000000,
+ .led_ctrl3 = 0x0030c300,
+ .open_drain = false,
};
static struct ar8327_platform_data rb2011_ar8327_data = {
.pad0_cfg = &rb2011_ar8327_pad0_cfg,
- .cpuport_cfg = {
+ .port0_cfg = {
.force_link = 1,
.speed = AR8327_PORT_SPEED_1000,
.duplex = 1,
.txpause = 1,
.rxpause = 1,
- }
+ },
+ .led_cfg = &rb2011_ar8327_led_cfg,
};
static struct mdio_board_info rb2011_mdio0_info[] = {
},
};
-static void __init rb2011_gmac_setup(void)
-{
- void __iomem *base;
- u32 t;
-
- base = ioremap(AR934X_GMAC_BASE, AR934X_GMAC_SIZE);
-
- t = __raw_readl(base + AR934X_GMAC_REG_ETH_CFG);
- t &= ~(AR934X_ETH_CFG_RGMII_GMAC0 | AR934X_ETH_CFG_MII_GMAC0 |
- AR934X_ETH_CFG_GMII_GMAC0 | AR934X_ETH_CFG_SW_ONLY_MODE);
- t |= AR934X_ETH_CFG_RGMII_GMAC0 | AR934X_ETH_CFG_SW_ONLY_MODE;
-
- __raw_writel(t, base + AR934X_GMAC_REG_ETH_CFG);
-
- iounmap(base);
-}
-
static void __init rb2011_wlan_init(void)
{
- u8 *hard_cfg = (u8 *) KSEG1ADDR(0x1f000000 + RB_HARD_CFG_OFFSET);
+ u8 *hard_cfg = (u8 *) KSEG1ADDR(0x1f000000);
u16 tag_len;
u8 *tag;
char *art_buf;
u8 wlan_mac[ETH_ALEN];
int err;
+ hard_cfg += rb2011_spi_partitions[1].offset;
err = routerboot_find_tag(hard_cfg, RB_HARD_CFG_SIZE, RB_ID_WLAN_DATA,
&tag, &tag_len);
if (err) {
static void __init rb2011_nand_init(void)
{
+ gpio_request_one(RB2011_GPIO_NAND_NCE, GPIOF_OUT_INIT_HIGH, "NAND nCE");
+
ath79_nfc_set_scan_fixup(rb2011_nand_scan_fixup);
ath79_nfc_set_parts(rb2011_nand_partitions,
ARRAY_SIZE(rb2011_nand_partitions));
ath79_nfc_set_select_chip(rb2011_nand_select_chip);
+ ath79_nfc_set_swap_dma(true);
ath79_register_nfc();
}
-static void __init rb2011_gpio_init(void)
+static int rb2011_get_port_link(unsigned port)
{
- gpio_request_one(RB2011_GPIO_NAND_NCE, GPIOF_OUT_INIT_HIGH, "NAND nCE");
+ if (port != 6)
+ return -EINVAL;
+
+ /* The Loss of signal line is active low */
+ return !gpio_get_value(RB2011_GPIO_SFP_LOS);
+}
+
+static void __init rb2011_sfp_init(void)
+{
+ gpio_request_one(RB2011_GPIO_SFP_LOS, GPIOF_IN, "SFP LOS");
+
+ rb2011_ar8327_pad6_cfg.mode = AR8327_PAD_MAC_SGMII;
+
+ rb2011_ar8327_data.pad6_cfg = &rb2011_ar8327_pad6_cfg;
+
+ rb2011_ar8327_sgmii_cfg.sgmii_ctrl = 0xc70167d0;
+ rb2011_ar8327_sgmii_cfg.serdes_aen = true;
+
+ rb2011_ar8327_data.sgmii_cfg = &rb2011_ar8327_sgmii_cfg;
+
+ rb2011_ar8327_data.port6_cfg.force_link = 1;
+ rb2011_ar8327_data.port6_cfg.speed = AR8327_PORT_SPEED_1000;
+ rb2011_ar8327_data.port6_cfg.duplex = 1;
+
+ rb2011_ar8327_data.get_port_link = rb2011_get_port_link;
}
static void __init rb2011_setup(void)
{
- rb2011_gpio_init();
+ rb2011_init_partitions();
ath79_register_m25p80(&rb2011_spi_flash_data);
rb2011_nand_init();
- rb2011_gmac_setup();
+ ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0 |
+ AR934X_ETH_CFG_SW_ONLY_MODE);
ath79_register_mdio(1, 0x0);
ath79_register_mdio(0, 0x0);
MIPS_MACHINE(ATH79_MACH_RB_2011L, "2011L", "MikroTik RouterBOARD 2011L",
rb2011_setup);
+static void __init rb2011us_setup(void)
+{
+ rb2011_setup();
+ rb2011_sfp_init();
+
+ ath79_register_usb();
+}
+
+MIPS_MACHINE(ATH79_MACH_RB_2011US, "2011US", "MikroTik RouterBOARD 2011UAS",
+ rb2011us_setup);
+
static void __init rb2011g_setup(void)
{
rb2011_setup();
+ rb2011_sfp_init();
rb2011_wlan_init();
+
+ ath79_register_usb();
}
MIPS_MACHINE(ATH79_MACH_RB_2011G, "2011G", "MikroTik RouterBOARD 2011UAS-2HnD",
projects / openwrt.git / blobdiff