can_bus_off(elm->dev);
}
+/* Compare a buffer to a fixed string */
+static int _memstrcmp(const u8 *mem, const char *str)
+{
+ return memcmp(mem, str, strlen(str));
+}
+
/* Assumes elm->lock taken. */
static void elm327_parse_error(struct elmcan *elm, int len)
{
frame.can_id = CAN_ERR_FLAG;
frame.can_dlc = CAN_ERR_DLC;
+ /* Filter possible error messages based on length of RX'd line */
switch (len) {
case 17:
- if (!memcmp(elm->rxbuf, "UNABLE TO CONNECT", 17)) {
+ if (!_memstrcmp(elm->rxbuf, "UNABLE TO CONNECT")) {
netdev_err(elm->dev,
"ELM327 reported UNABLE TO CONNECT. Please check your setup.\n");
}
break;
case 11:
- if (!memcmp(elm->rxbuf, "BUFFER FULL", 11)) {
+ if (!_memstrcmp(elm->rxbuf, "BUFFER FULL")) {
/* This case will only happen if the last data
* line was complete.
* Otherwise, elm327_parse_frame() will heuristically
}
break;
case 9:
- if (!memcmp(elm->rxbuf, "BUS ERROR", 9))
+ if (!_memstrcmp(elm->rxbuf, "BUS ERROR"))
frame.can_id |= CAN_ERR_BUSERROR;
- if (!memcmp(elm->rxbuf, "CAN ERROR", 9))
+ if (!_memstrcmp(elm->rxbuf, "CAN ERROR"))
frame.can_id |= CAN_ERR_PROT;
- if (!memcmp(elm->rxbuf, "<RX ERROR", 9))
+ if (!_memstrcmp(elm->rxbuf, "<RX ERROR"))
frame.can_id |= CAN_ERR_PROT;
break;
case 8:
- if (!memcmp(elm->rxbuf, "BUS BUSY", 8)) {
+ if (!_memstrcmp(elm->rxbuf, "BUS BUSY")) {
frame.can_id |= CAN_ERR_PROT;
frame.data[2] = CAN_ERR_PROT_OVERLOAD;
}
- if (!memcmp(elm->rxbuf, "FB ERROR", 8)) {
+ if (!_memstrcmp(elm->rxbuf, "FB ERROR")) {
frame.can_id |= CAN_ERR_PROT;
frame.data[2] = CAN_ERR_PROT_TX;
}
break;
- case 5:
- if (!memcmp(elm->rxbuf, "ERR", 3)) {
+ case 5: /* ERR is followed by two digits, hence line length 5 */
+ if (!_memstrcmp(elm->rxbuf, "ERR")) {
netdev_err(elm->dev, "ELM327 reported an ERR%c%c. Please power it off and on again.\n",
elm->rxbuf[3], elm->rxbuf[4]);
frame.can_id |= CAN_ERR_CRTL;
}
break;
default:
- /* Don't emit an error frame if we're unsure */
- return;
+ /* Something else has happened.
+ * Maybe garbage on the UART line.
+ * Emit a generic error frame.
+ */
+ break;
}
elm327_feed_frame_to_netdev(elm, &frame);
/* The line is likely garbled anyway, so bail.
* The main code will restart listening.
*/
- elm327_kick_into_cmd_mode(elm);
return -ENODATA;
}
/* Check for RTR frame */
if (elm->rxfill >= hexlen + 3 &&
- !memcmp(&elm->rxbuf[hexlen], "RTR", 3)) {
+ !_memstrcmp(&elm->rxbuf[hexlen], "RTR")) {
frame.can_id |= CAN_RTR_FLAG;
}
if (elm->drop_next_line) {
elm->drop_next_line = 0;
return;
- } else if (elm->rxbuf[0] == 'A' && elm->rxbuf[1] == 'T') {
+ } else if (!_memstrcmp(elm->rxbuf, "AT")) {
return;
}
/* Dummy needed to use bitrate_const */
static int elmcan_do_set_bittiming(struct net_device *netdev)
{
- (void)netdev;
-
return 0;
}
{
int status;
- pr_info("ELM327 based best effort CAN interface driver\n");
- pr_info("This device is severely limited as a CAN interface, see documentation.\n");
-
#if LINUX_VERSION_CODE < KERNEL_VERSION(5,14,0)
status = tty_register_ldisc(N_ELMCAN, &elmcan_ldisc);
#else