/* * Low-level hardware driver -- IEEE 802.11 driver (80211.o) interface * Copyright 2002-2005, Devicescape Software, Inc. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #ifndef D80211_H #define D80211_H #include #include #include #include #include #include "d80211_shared.h" /* Note! Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be * called in hardware interrupt context. The low-level driver must not call any * other functions in hardware interrupt context. If there is a need for such * call, the low-level driver should first ACK the interrupt and perform the * IEEE 802.11 code call after this, e.g., from a scheduled tasklet (in * software interrupt context). */ /* * Frame format used when passing frame between low-level hardware drivers * and IEEE 802.11 driver the same as used in the wireless media, i.e., * buffers start with IEEE 802.11 header and include the same octets that * are sent over air. * * If hardware uses IEEE 802.3 headers (and perform 802.3 <-> 802.11 * conversion in firmware), upper layer 802.11 code needs to be changed to * support this. * * If the receive frame format is not the same as the real frame sent * on the wireless media (e.g., due to padding etc.), upper layer 802.11 code * could be updated to provide support for such format assuming this would * optimize the performance, e.g., by removing need to re-allocation and * copying of the data. */ /* Interface version (used for compatibility verification) */ #define IEEE80211_VERSION 2 /* Channel information structure. Low-level driver is expected to fill in chan, * freq, and val fields. Other fields will be filled in by 80211.o based on * hostapd information and low-level driver does not need to use them. The * limits for each channel will be provided in 'struct ieee80211_conf' when * configuring the low-level driver with hw->config callback. */ struct ieee80211_channel { short chan; /* channel number (IEEE 802.11) */ short freq; /* frequency in MHz */ int val; /* hw specific value for the channel */ int flag; /* flag for hostapd use (IEEE80211_CHAN_*) */ unsigned char power_level; unsigned char antenna_max; }; struct ieee80211_rate { int rate; /* rate in 100 kbps */ int val; /* hw specific value for the rate */ int flags; /* IEEE80211_RATE_ flags */ int val2; /* hw specific value for the rate when using short preamble * (only when IEEE80211_RATE_PREAMBLE2 flag is set, i.e., for * 2, 5.5, and 11 Mbps) */ signed char min_rssi_ack; unsigned char min_rssi_ack_delta; /* following fields are set by 80211.o and need not be filled by the * low-level driver */ int rate_inv; /* inverse of the rate (LCM(all rates) / rate) for * optimizing channel utilization estimates */ }; struct ieee80211_hw_modes { int mode; int num_channels; struct ieee80211_channel *channels; int num_rates; struct ieee80211_rate *rates; }; struct ieee80211_tx_queue_params { int aifs; /* 0 .. 255; -1 = use default */ int cw_min; /* 2^n-1: 1, 3, 7, .. , 1023; 0 = use default */ int cw_max; /* 2^n-1: 1, 3, 7, .. , 1023; 0 = use default */ int burst_time; /* maximum burst time in 0.1 ms (i.e., 10 = 1 ms); * 0 = disabled */ }; #define NUM_TX_DATA_QUEUES 6 struct ieee80211_tx_queue_stats_data { unsigned int len; /* num packets in queue */ unsigned int limit; /* queue len (soft) limit */ unsigned int count; /* total num frames sent */ }; struct ieee80211_tx_queue_stats { struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES]; }; #ifndef IEEE80211_TX_QUEUE_NUMS #define IEEE80211_TX_QUEUE_NUMS /* TODO: these need to be synchronized with hostapd_ioctl.h; make a shared * header file that can be included into low-level drivers, 80211.o, and * hostapd */ enum { IEEE80211_TX_QUEUE_DATA0 = 0, IEEE80211_TX_QUEUE_DATA1 = 1, IEEE80211_TX_QUEUE_DATA2 = 2, IEEE80211_TX_QUEUE_DATA3 = 3, IEEE80211_TX_QUEUE_DATA4 = 4, IEEE80211_TX_QUEUE_SVP = 5, IEEE80211_TX_QUEUE_AFTER_BEACON = 6, IEEE80211_TX_QUEUE_BEACON = 7 }; #endif /* IEEE80211_TX_QUEUE_NUMS */ struct ieee80211_low_level_stats { unsigned int dot11ACKFailureCount; unsigned int dot11RTSFailureCount; unsigned int dot11FCSErrorCount; unsigned int dot11RTSSuccessCount; }; /* Transmit control fields. This data structure is passed to low-level driver * with each TX frame. The low-level driver is responsible for configuring * the hardware to use given values (depending on what is supported). */ #define HW_KEY_IDX_INVALID -1 struct ieee80211_tx_control { enum { PKT_NORMAL = 0, PKT_PROBE_RESP } pkt_type; int tx_rate; /* Transmit rate, given as the hw specific value for the * rate (from struct ieee80211_rate) */ int rts_cts_rate; /* Transmit rate for RTS/CTS frame, given as the hw * specific value for the rate (from * struct ieee80211_rate) */ #define IEEE80211_TXCTL_REQ_TX_STATUS (1<<0)/* request TX status callback for * this frame */ #define IEEE80211_TXCTL_DO_NOT_ENCRYPT (1<<1) /* send this frame without * encryption; e.g., for EAPOL * frames */ #define IEEE80211_TXCTL_USE_RTS_CTS (1<<2) /* use RTS-CTS before sending * frame */ #define IEEE80211_TXCTL_USE_CTS_PROTECT (1<<3) /* use CTS protection for the * frame (e.g., for combined * 802.11g / 802.11b networks) */ #define IEEE80211_TXCTL_NO_ACK (1<<4) /* tell the low level not to * wait for an ack */ #define IEEE80211_TXCTL_RATE_CTRL_PROBE (1<<5) #define IEEE80211_TXCTL_CLEAR_DST_MASK (1<<6) #define IEEE80211_TXCTL_REQUEUE (1<<7) #define IEEE80211_TXCTL_FIRST_FRAGMENT (1<<8) /* this is a first fragment of * the frame */ #define IEEE80211_TXCTL_TKIP_NEW_PHASE1_KEY (1<<9) u32 flags; /* tx control flags defined * above */ u16 rts_cts_duration; /* duration field for RTS/CTS frame */ u8 retry_limit; /* 1 = only first attempt, 2 = one retry, .. */ u8 power_level; /* per-packet transmit power level, in dBm */ u8 antenna_sel; /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */ s8 key_idx; /* -1 = do not encrypt, >= 0 keyidx from * hw->set_key() */ u8 icv_len; /* length of the ICV/MIC field in octets */ u8 iv_len; /* length of the IV field in octets */ u8 tkip_key[16]; /* generated phase2/phase1 key for hw TKIP */ u8 queue; /* hardware queue to use for this frame; * 0 = highest, hw->queues-1 = lowest */ u8 sw_retry_attempt; /* number of times hw has tried to * transmit frame (not incl. hw retries) */ int rateidx; /* internal 80211.o rateidx */ int alt_retry_rate; /* retry rate for the last retries, given as the * hw specific value for the rate (from * struct ieee80211_rate). To be used to limit * packet dropping when probing higher rates, if hw * supports multiple retry rates. -1 = not used */ int type; /* internal */ int ifindex; /* internal */ }; #define RX_FLAG_MMIC_ERROR 0x1 #define RX_FLAG_DECRYPTED 0x2 /* Receive status. The low-level driver should provide this information * (the subset supported by hardware) to the 802.11 code with each received * frame. */ struct ieee80211_rx_status { u64 hosttime; u64 mactime; int freq; /* receive frequency in Mhz */ int channel; int phymode; int ssi; int signal; int noise; int antenna; int rate; int flag; }; /* Transmit status. The low-level driver should provide this information * (the subset supported by hardware) to the 802.11 code for each transmit * frame. */ struct ieee80211_tx_status { /* copied ieee80211_tx_control structure */ struct ieee80211_tx_control control; #define IEEE80211_TX_STATUS_TX_FILTERED (1<<0) #define IEEE80211_TX_STATUS_ACK (1<<1) /* whether the TX frame was ACKed */ u32 flags; /* tx staus flags defined above */ int ack_signal; /* measured signal strength of the ACK frame */ int excessive_retries; int retry_count; int queue_length; /* information about TX queue */ int queue_number; }; /** * struct ieee80211_conf - configuration of the device * * This struct indicates how the driver shall configure the hardware. * * @radio_enabled: when zero, driver is required to switch off the radio. */ struct ieee80211_conf { int channel; /* IEEE 802.11 channel number */ int freq; /* MHz */ int channel_val; /* hw specific value for the channel */ int phymode; /* MODE_IEEE80211A, .. */ unsigned int regulatory_domain; int radio_enabled; int beacon_int; #define IEEE80211_CONF_SHORT_SLOT_TIME (1<<0) /* use IEEE 802.11g Short Slot * Time */ #define IEEE80211_CONF_SSID_HIDDEN (1<<1) /* do not broadcast the ssid */ u32 flags; /* configuration flags defined above */ u8 power_level; /* transmit power limit for current * regulatory domain; in dBm */ u8 antenna_max; /* maximum antenna gain */ short tx_power_reduction; /* in 0.1 dBm */ int antenna_sel; /* default antenna conf: * 0 = default/diversity, * 1 = Ant0, * 2 = Ant1 */ int antenna_def; int antenna_mode; /* Following five fields are used for IEEE 802.11H */ unsigned int radar_detect; unsigned int spect_mgmt; unsigned int quiet_duration; /* duration of quiet period */ unsigned int quiet_offset; /* how far into the beacon is the quiet * period */ unsigned int quiet_period; u8 radar_firpwr_threshold; u8 radar_rssi_threshold; u8 pulse_height_threshold; u8 pulse_rssi_threshold; u8 pulse_inband_threshold; }; /** * enum ieee80211_if_types - types of 802.11 network interfaces * * @IEEE80211_IF_TYPE_AP: interface in AP mode. * @IEEE80211_IF_TYPE_MGMT: special interface for communication with hostap * daemon. Drivers should never see this type. * @IEEE80211_IF_TYPE_STA: interface in STA (client) mode. * @IEEE80211_IF_TYPE_IBSS: interface in IBSS (ad-hoc) mode. * @IEEE80211_IF_TYPE_MNTR: interface in monitor (rfmon) mode. * @IEEE80211_IF_TYPE_WDS: interface in WDS mode. * @IEEE80211_IF_TYPE_VLAN: not used. */ enum ieee80211_if_types { IEEE80211_IF_TYPE_AP = 0x00000000, IEEE80211_IF_TYPE_MGMT = 0x00000001, IEEE80211_IF_TYPE_STA = 0x00000002, IEEE80211_IF_TYPE_IBSS = 0x00000003, IEEE80211_IF_TYPE_MNTR = 0x00000004, IEEE80211_IF_TYPE_WDS = 0x5A580211, IEEE80211_IF_TYPE_VLAN = 0x00080211, }; /** * struct ieee80211_if_init_conf - initial configuration of an interface * * @if_id: internal interface ID. This number has no particular meaning to * drivers and the only allowed usage is to pass it to * ieee80211_beacon_get() and ieee80211_get_buffered_bc() functions. * This field is not valid for monitor interfaces * (interfaces of %IEEE80211_IF_TYPE_MNTR type). * @type: one of &enum ieee80211_if_types constants. Determines the type of * added/removed interface. * @mac_addr: pointer to MAC address of the interface. This pointer is valid * until the interface is removed (i.e. it cannot be used after * remove_interface() callback was called for this interface). * * This structure is used in add_interface() and remove_interface() * callbacks of &struct ieee80211_hw. */ struct ieee80211_if_init_conf { int if_id; int type; void *mac_addr; }; /** * struct ieee80211_if_conf - configuration of an interface * * @type: type of the interface. This is always the same as was specified in * &struct ieee80211_if_init_conf. The type of an interface never changes * during the life of the interface; this field is present only for * convenience. * @bssid: BSSID of the network we are associated to/creating. * @ssid: used (together with @ssid_len) by drivers for hardware that * generate beacons independently. The pointer is valid only during the * config_interface() call, so copy the value somewhere if you need * it. * @ssid_len: length of the @ssid field. * @generic_elem: used (together with @generic_elem_len) by drivers for * hardware that generate beacons independently. The pointer is valid * only during the config_interface() call, so copy the value somewhere * if you need it. * @generic_elem_len: length of the generic element. * @beacon: beacon template. Valid only if @host_gen_beacon_template in * &struct ieee80211_hw is set. The driver is responsible of freeing * the sk_buff. * * This structure is passed to the config_interface() callback of * &struct ieee80211_hw. */ struct ieee80211_if_conf { int type; u8 *bssid; u8 *ssid; size_t ssid_len; u8 *generic_elem; size_t generic_elem_len; struct sk_buff *beacon; }; typedef enum { ALG_NONE, ALG_WEP, ALG_TKIP, ALG_CCMP, ALG_NULL } ieee80211_key_alg; struct ieee80211_key_conf { int hw_key_idx; /* filled + used by low-level driver */ ieee80211_key_alg alg; int keylen; #define IEEE80211_KEY_FORCE_SW_ENCRYPT (1<<0) /* to be cleared by low-level driver */ #define IEEE80211_KEY_DEFAULT_TX_KEY (1<<1) /* This key is the new default TX key (used only for broadcast keys). */ #define IEEE80211_KEY_DEFAULT_WEP_ONLY (1<<2) /* static WEP is the only configured security policy; this allows some low-level drivers to determine when hwaccel can be used */ u32 flags; /* key configuration flags defined above */ s8 keyidx; /* WEP key index */ u8 key[0]; }; #define IEEE80211_SCAN_START 1 #define IEEE80211_SCAN_END 2 struct ieee80211_scan_conf { int scan_channel; /* IEEE 802.11 channel number to do passive scan * on */ int scan_freq; /* new freq in MHz to switch to for passive scan */ int scan_channel_val; /* hw specific value for the channel */ int scan_phymode; /* MODE_IEEE80211A, .. */ unsigned char scan_power_level; unsigned char scan_antenna_max; int running_channel; /* IEEE 802.11 channel number we operate on * normally */ int running_freq; /* freq in MHz we're operating on normally */ int running_channel_val; /* hw specific value for the channel */ int running_phymode; unsigned char running_power_level; unsigned char running_antenna_max; int scan_time; /* time a scan will take in us */ int tries; struct sk_buff *skb; /* skb to transmit before changing channels, maybe * NULL for none */ struct ieee80211_tx_control *tx_control; }; #define IEEE80211_SEQ_COUNTER_RX 0 #define IEEE80211_SEQ_COUNTER_TX 1 typedef enum { SET_KEY, DISABLE_KEY, REMOVE_ALL_KEYS, } set_key_cmd; /* This is driver-visible part of the per-hw state the stack keeps. * If you change something in here, call ieee80211_update_hw() to * notify the stack about the change. */ struct ieee80211_hw { /* these are assigned by d80211, don't write */ int index; struct ieee80211_conf conf; /* Pointer to the private area that was * allocated with this struct for you. */ void *priv; /* The rest is information about your hardware */ struct device *dev; /* permanent mac address */ u8 perm_addr[ETH_ALEN]; /* TODO: frame_type 802.11/802.3, sw_encryption requirements */ /* Some wireless LAN chipsets generate beacons in the hardware/firmware * and others rely on host generated beacons. This option is used to * configure the upper layer IEEE 802.11 module to generate beacons. * The low-level driver can use ieee80211_beacon_get() to fetch the * next beacon frame. */ #define IEEE80211_HW_HOST_GEN_BEACON (1<<0) /* The device needs to be supplied with a beacon template only. */ #define IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE (1<<1) /* Some devices handle decryption internally and do not * indicate whether the frame was encrypted (unencrypted frames * will be dropped by the hardware, unless specifically allowed * through) */ #define IEEE80211_HW_DEVICE_HIDES_WEP (1<<2) /* Whether RX frames passed to ieee80211_rx() include FCS in the end */ #define IEEE80211_HW_RX_INCLUDES_FCS (1<<3) /* Some wireless LAN chipsets buffer broadcast/multicast frames for * power saving stations in the hardware/firmware and others rely on * the host system for such buffering. This option is used to * configure the IEEE 802.11 upper layer to buffer broadcast/multicast * frames when there are power saving stations so that low-level driver * can fetch them with ieee80211_get_buffered_bc(). */ #define IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING (1<<4) #define IEEE80211_HW_WEP_INCLUDE_IV (1<<5) /* will data nullfunc frames get proper TX status callback */ #define IEEE80211_HW_DATA_NULLFUNC_ACK (1<<6) /* Force software encryption for TKIP packets if WMM is enabled. */ #define IEEE80211_HW_NO_TKIP_WMM_HWACCEL (1<<7) /* Some devices handle Michael MIC internally and do not include MIC in * the received packets passed up. device_strips_mic must be set * for such devices. The 'encryption' frame control bit is expected to * be still set in the IEEE 802.11 header with this option unlike with * the device_hides_wep configuration option. */ #define IEEE80211_HW_DEVICE_STRIPS_MIC (1<<8) /* Device is capable of performing full monitor mode even during * normal operation. */ #define IEEE80211_HW_MONITOR_DURING_OPER (1<<9) /* Set if the low-level driver supports skb fraglist (NETIF_F_FRAGLIST), * i.e. more than one skb per frame */ #define IEEE80211_HW_FRAGLIST (1<<10) /* calculate Michael MIC for an MSDU when doing hwcrypto */ #define IEEE80211_HW_TKIP_INCLUDE_MMIC (1<<12) /* Do TKIP phase1 key mixing in stack to support cards only do * phase2 key mixing when doing hwcrypto */ #define IEEE80211_HW_TKIP_REQ_PHASE1_KEY (1<<13) /* Do TKIP phase1 and phase2 key mixing in stack and send the generated * per-packet RC4 key with each TX frame when doing hwcrypto */ #define IEEE80211_HW_TKIP_REQ_PHASE2_KEY (1<<14) u32 flags; /* hardware flags defined above */ /* Set to the size of a needed device specific skb headroom for TX skbs. */ unsigned int extra_tx_headroom; /* This is the time in us to change channels */ int channel_change_time; /* This is maximum value for rssi reported by this device */ int maxssi; int num_modes; struct ieee80211_hw_modes *modes; /* Number of available hardware TX queues for data packets. * WMM requires at least four queues. */ int queues; }; /* Configuration block used by the low-level driver to tell the 802.11 code * about supported hardware features and to pass function pointers to callback * functions. */ struct ieee80211_ops { /* Handler that 802.11 module calls for each transmitted frame. * skb contains the buffer starting from the IEEE 802.11 header. * The low-level driver should send the frame out based on * configuration in the TX control data. */ int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_tx_control *control); /* Handler for performing hardware reset. */ int (*reset)(struct ieee80211_hw *hw); /* Handler that is called when any netdevice attached to the hardware * device is set UP for the first time. This can be used, e.g., to * enable interrupts and beacon sending. */ int (*open)(struct ieee80211_hw *hw); /* Handler that is called when the last netdevice attached to the * hardware device is set DOWN. This can be used, e.g., to disable * interrupts and beacon sending. */ int (*stop)(struct ieee80211_hw *hw); /* Handler for asking a driver if a new interface can be added (or, * more exactly, set UP). If the handler returns zero, the interface * is added. Driver should perform any initialization it needs prior * to returning zero. By returning non-zero addition of the interface * is inhibited. Unless monitor_during_oper is set, it is guaranteed * that monitor interfaces and normal interfaces are mutually * exclusive. The open() handler is called after add_interface() * if this is the first device added. At least one of the open() * open() and add_interface() callbacks has to be assigned. If * add_interface() is NULL, one STA interface is permitted only. */ int (*add_interface)(struct ieee80211_hw *hw, struct ieee80211_if_init_conf *conf); /* Notify a driver that an interface is going down. The stop() handler * is called prior to this if this is a last interface. */ void (*remove_interface)(struct ieee80211_hw *hw, struct ieee80211_if_init_conf *conf); /* Handler for configuration requests. IEEE 802.11 code calls this * function to change hardware configuration, e.g., channel. */ int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf); /* Handler for configuration requests related to interfaces (e.g. * BSSID). */ int (*config_interface)(struct ieee80211_hw *hw, int if_id, struct ieee80211_if_conf *conf); /* ieee80211 drivers do not have access to the &struct net_device * that is (are) connected with their device. Hence (and because * we need to combine the multicast lists and flags for multiple * virtual interfaces), they cannot assign set_multicast_list. * The parameters here replace dev->flags and dev->mc_count, * dev->mc_list is replaced by calling ieee80211_get_mc_list_item. */ void (*set_multicast_list)(struct ieee80211_hw *hw, unsigned short flags, int mc_count); /* Set TIM bit handler. If the hardware/firmware takes care of beacon * generation, IEEE 802.11 code uses this function to tell the * low-level to set (or clear if set==0) TIM bit for the given aid. If * host system is used to generate beacons, this handler is not used * and low-level driver should set it to NULL. */ int (*set_tim)(struct ieee80211_hw *hw, int aid, int set); /* Set encryption key. IEEE 802.11 module calls this function to set * encryption keys. addr is ff:ff:ff:ff:ff:ff for default keys and * station hwaddr for individual keys. aid of the station is given * to help low-level driver in selecting which key->hw_key_idx to use * for this key. TX control data will use the hw_key_idx selected by * the low-level driver. */ int (*set_key)(struct ieee80211_hw *hw, set_key_cmd cmd, u8 *addr, struct ieee80211_key_conf *key, int aid); /* Set TX key index for default/broadcast keys. This is needed in cases * where wlan card is doing full WEP/TKIP encapsulation (wep_include_iv * is not set), in other cases, this function pointer can be set to * NULL since the IEEE 802. 11 module takes care of selecting the key * index for each TX frame. */ int (*set_key_idx)(struct ieee80211_hw *hw, int idx); /* Enable/disable IEEE 802.1X. This item requests wlan card to pass * unencrypted EAPOL-Key frames even when encryption is configured. * If the wlan card does not require such a configuration, this * function pointer can be set to NULL. */ int (*set_ieee8021x)(struct ieee80211_hw *hw, int use_ieee8021x); /* Set port authorization state (IEEE 802.1X PAE) to be authorized * (authorized=1) or unauthorized (authorized=0). This function can be * used if the wlan hardware or low-level driver implements PAE. * 80211.o module will anyway filter frames based on authorization * state, so this function pointer can be NULL if low-level driver does * not require event notification about port state changes. */ int (*set_port_auth)(struct ieee80211_hw *hw, u8 *addr, int authorized); /* Ask the hardware to do a passive scan on a new channel. The hardware * will do what ever is required to nicely leave the current channel * including transmit any CTS packets, etc. */ int (*passive_scan)(struct ieee80211_hw *hw, int state, struct ieee80211_scan_conf *conf); /* Ask the hardware to service the scan request, no need to start * the scan state machine in stack. */ int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len); /* return low-level statistics */ int (*get_stats)(struct ieee80211_hw *hw, struct ieee80211_low_level_stats *stats); /* Enable/disable test modes; mode = IEEE80211_TEST_* */ int (*test_mode)(struct ieee80211_hw *hw, int mode); /* Configuration of test parameters */ int (*test_param)(struct ieee80211_hw *hw, int param, int value); /* For devices that generate their own beacons and probe response * or association responses this updates the state of privacy_invoked * returns 0 for success or an error number */ int (*set_privacy_invoked)(struct ieee80211_hw *hw, int privacy_invoked); /* For devices that have internal sequence counters, allow 802.11 * code to access the current value of a counter */ int (*get_sequence_counter)(struct ieee80211_hw *hw, u8* addr, u8 keyidx, u8 txrx, u32* iv32, u16* iv16); /* Configuration of RTS threshold (if device needs it) */ int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value); /* Configuration of fragmentation threshold. * Assign this if the device does fragmentation by itself, * if this method is assigned then the stack will not do * fragmentation. */ int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value); /* Configuration of retry limits (if device needs it) */ int (*set_retry_limit)(struct ieee80211_hw *hw, u32 short_retry, u32 long_retr); /* Number of STAs in STA table notification (NULL = disabled) */ void (*sta_table_notification)(struct ieee80211_hw *hw, int num_sta); /* Configure TX queue parameters (EDCF (aifs, cw_min, cw_max), * bursting) for a hardware TX queue. * queue = IEEE80211_TX_QUEUE_*. */ int (*conf_tx)(struct ieee80211_hw *hw, int queue, const struct ieee80211_tx_queue_params *params); /* Get statistics of the current TX queue status. This is used to get * number of currently queued packets (queue length), maximum queue * size (limit), and total number of packets sent using each TX queue * (count). This information is used for WMM to find out which TX * queues have room for more packets and by hostapd to provide * statistics about the current queueing state to external programs. */ int (*get_tx_stats)(struct ieee80211_hw *hw, struct ieee80211_tx_queue_stats *stats); /* Get the current TSF timer value from firmware/hardware. Currently, * this is only used for IBSS mode debugging and, as such, is not a * required function. */ u64 (*get_tsf)(struct ieee80211_hw *hw); /* Reset the TSF timer and allow firmware/hardware to synchronize with * other STAs in the IBSS. This is only used in IBSS mode. This * function is optional if the firmware/hardware takes full care of * TSF synchronization. */ void (*reset_tsf)(struct ieee80211_hw *hw); /* Setup beacon data for IBSS beacons. Unlike access point (Master), * IBSS uses a fixed beacon frame which is configured using this * function. This handler is required only for IBSS mode. */ int (*beacon_update)(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_tx_control *control); /* Determine whether the last IBSS beacon was sent by us. This is * needed only for IBSS mode and the result of this function is used to * determine whether to reply to Probe Requests. */ int (*tx_last_beacon)(struct ieee80211_hw *hw); }; /* Allocate a new hardware device. This must be called once for each * hardware device. The returned pointer must be used to refer to this * device when calling other functions. 802.11 code allocates a private data * area for the low-level driver. The size of this area is given as * priv_data_len. */ struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, struct ieee80211_ops *ops); /* Register hardware device to the IEEE 802.11 code and kernel. Low-level * drivers must call this function before using any other IEEE 802.11 * function. */ int ieee80211_register_hw(struct ieee80211_hw *hw); /* driver can use this and ieee80211_get_rx_led_name to get the * name of the registered LEDs after ieee80211_register_hw * was called. * This is useful to set the default trigger on the LED class * device that your driver should export for each LED the device * has, that way the default behaviour will be as expected but * the user can still change it/turn off the LED etc. */ #ifdef CONFIG_D80211_LEDS extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); #endif static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) { #ifdef CONFIG_D80211_LEDS return __ieee80211_get_tx_led_name(hw); #else return NULL; #endif } static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) { #ifdef CONFIG_D80211_LEDS return __ieee80211_get_rx_led_name(hw); #else return NULL; #endif } /* Call this function if you changed the hardware description after * ieee80211_register_hw */ int ieee80211_update_hw(struct ieee80211_hw *hw); /* Unregister a hardware device. This function instructs 802.11 code to free * allocated resources and unregister netdevices from the kernel. */ void ieee80211_unregister_hw(struct ieee80211_hw *hw); /* Free everything that was allocated including private data of a driver. */ void ieee80211_free_hw(struct ieee80211_hw *hw); /* Receive frame callback function. The low-level driver uses this function to * send received frames to the IEEE 802.11 code. Receive buffer (skb) must * start with IEEE 802.11 header. */ void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_rx_status *status); void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_rx_status *status); /* Transmit status callback function. The low-level driver must call this * function to report transmit status for all the TX frames that had * req_tx_status set in the transmit control fields. In addition, this should * be called at least for all unicast frames to provide information for TX rate * control algorithm. In order to maintain all statistics, this function is * recommended to be called after each frame, including multicast/broadcast, is * sent. */ void ieee80211_tx_status(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_tx_status *status); void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_tx_status *status); /** * ieee80211_beacon_get - beacon generation function * @hw: pointer obtained from ieee80211_alloc_hw(). * @if_id: interface ID from &struct ieee80211_if_init_conf. * @control: will be filled with information needed to send this beacon. * * If the beacon frames are generated by the host system (i.e., not in * hardware/firmware), the low-level driver uses this function to receive * the next beacon frame from the 802.11 code. The low-level is responsible * for calling this function before beacon data is needed (e.g., based on * hardware interrupt). Returned skb is used only once and low-level driver * is responsible of freeing it. */ struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, int if_id, struct ieee80211_tx_control *control); /** * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames * @hw: pointer as obtained from ieee80211_alloc_hw(). * @if_id: interface ID from &struct ieee80211_if_init_conf. * @control: will be filled with information needed to send returned frame. * * Function for accessing buffered broadcast and multicast frames. If * hardware/firmware does not implement buffering of broadcast/multicast * frames when power saving is used, 802.11 code buffers them in the host * memory. The low-level driver uses this function to fetch next buffered * frame. In most cases, this is used when generating beacon frame. This * function returns a pointer to the next buffered skb or NULL if no more * buffered frames are available. * * Note: buffered frames are returned only after DTIM beacon frame was * generated with ieee80211_beacon_get() and the low-level driver must thus * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns * NULL if the previous generated beacon was not DTIM, so the low-level driver * does not need to check for DTIM beacons separately and should be able to * use common code for all beacons. */ struct sk_buff * ieee80211_get_buffered_bc(struct ieee80211_hw *hw, int if_id, struct ieee80211_tx_control *control); /* Low level drivers that have their own MLME and MAC indicate * the aid for an associating station with this call */ int ieee80211_set_aid_for_sta(struct ieee80211_hw *hw, u8 *peer_address, u16 aid); /* Given an sk_buff with a raw 802.11 header at the data pointer this function * returns the 802.11 header length in bytes (not including encryption * headers). If the data in the sk_buff is too short to contain a valid 802.11 * header the function returns 0. */ int ieee80211_get_hdrlen_from_skb(struct sk_buff *skb); /* Like ieee80211_get_hdrlen_from_skb() but takes a FC in CPU order. */ int ieee80211_get_hdrlen(u16 fc); /* Function for net interface operation. IEEE 802.11 may use multiple kernel * netdevices for each hardware device. The low-level driver does not "see" * these interfaces, so it should use this function to perform netif * operations on all interface. */ /* This function is deprecated. */ typedef enum { NETIF_ATTACH, NETIF_DETACH, NETIF_START, NETIF_STOP, NETIF_WAKE, NETIF_IS_STOPPED, NETIF_UPDATE_TX_START } Netif_Oper; int ieee80211_netif_oper(struct ieee80211_hw *hw, Netif_Oper op); /** * ieee80211_wake_queue - wake specific queue * @hw: pointer as obtained from ieee80211_alloc_hw(). * @queue: queue number (counted from zero). * * Drivers should use this function instead of netif_wake_queue. */ void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue); /** * ieee80211_stop_queue - stop specific queue * @hw: pointer as obtained from ieee80211_alloc_hw(). * @queue: queue number (counted from zero). * * Drivers should use this function instead of netif_stop_queue. */ void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue); /** * ieee80211_start_queues - start all queues * @hw: pointer to as obtained from ieee80211_alloc_hw(). * * Drivers should use this function instead of netif_start_queue. */ void ieee80211_start_queues(struct ieee80211_hw *hw); /** * ieee80211_stop_queues - stop all queues * @hw: pointer as obtained from ieee80211_alloc_hw(). * * Drivers should use this function instead of netif_stop_queue. */ void ieee80211_stop_queues(struct ieee80211_hw *hw); /** * ieee80211_get_mc_list_item - iteration over items in multicast list * @hw: pointer as obtained from ieee80211_alloc_hw(). * @prev: value returned by previous call to ieee80211_get_mc_list_item() or * NULL to start a new iteration. * @ptr: pointer to buffer of void * type for internal usage of * ieee80211_get_mc_list_item(). * * Iterates over items in multicast list of given device. To get the first * item, pass NULL in @prev and in *@ptr. In subsequent calls, pass the * value returned by previous call in @prev. Don't alter *@ptr during * iteration. When there are no more items, NULL is returned. */ struct dev_mc_list * ieee80211_get_mc_list_item(struct ieee80211_hw *hw, struct dev_mc_list *prev, void **ptr); /* called by driver to notify scan status completed */ void ieee80211_scan_completed(struct ieee80211_hw *hw); /* Function to indicate Radar Detection. The low level driver must call this * function to indicate the presence of radar in the current channel. * Additionally the radar type also could be sent */ int ieee80211_radar_status(struct ieee80211_hw *hw, int channel, int radar, int radar_type); /* Test modes */ enum { IEEE80211_TEST_DISABLE = 0 /* terminate testing */, IEEE80211_TEST_UNMASK_CHANNELS = 1 /* allow all channels to be used */, IEEE80211_TEST_CONTINUOUS_TX = 2, }; /* Test parameters */ enum { /* TX power in hardware specific raw value */ IEEE80211_TEST_PARAM_TX_POWER_RAW = 0, /* TX rate in hardware specific raw value */ IEEE80211_TEST_PARAM_TX_RATE_RAW = 1, /* Continuous TX pattern (32-bit) */ IEEE80211_TEST_PARAM_TX_PATTERN = 2, /* TX power in 0.1 dBm, 100 = 10 dBm */ IEEE80211_TEST_PARAM_TX_POWER = 3, /* TX rate in 100 kbps, 540 = 54 Mbps */ IEEE80211_TEST_PARAM_TX_RATE = 4, IEEE80211_TEST_PARAM_TX_ANT_SEL_RAW = 5, }; /* IEEE 802.11 defines */ #define FCS_LEN 4 #define IEEE80211_DATA_LEN 2304 /* Maximum size for the MA-UNITDATA primitive, 802.11 standard section 6.2.1.1.2. The figure in section 7.1.2 suggests a body size of up to 2312 bytes is allowed, which is a bit confusing, I suspect this represents the 2304 bytes of real data, plus a possible 8 bytes of WEP IV and ICV. (this interpretation suggested by Ramiro Barreiro) */ #define IEEE80211_FCTL_VERS 0x0003 #define IEEE80211_FCTL_FTYPE 0x000c #define IEEE80211_FCTL_STYPE 0x00f0 #define IEEE80211_FCTL_TODS 0x0100 #define IEEE80211_FCTL_FROMDS 0x0200 #define IEEE80211_FCTL_MOREFRAGS 0x0400 #define IEEE80211_FCTL_RETRY 0x0800 #define IEEE80211_FCTL_PM 0x1000 #define IEEE80211_FCTL_MOREDATA 0x2000 #define IEEE80211_FCTL_PROTECTED 0x4000 #define IEEE80211_FCTL_ORDER 0x8000 #define IEEE80211_SCTL_FRAG 0x000F #define IEEE80211_SCTL_SEQ 0xFFF0 #define IEEE80211_FTYPE_MGMT 0x0000 #define IEEE80211_FTYPE_CTL 0x0004 #define IEEE80211_FTYPE_DATA 0x0008 /* management */ #define IEEE80211_STYPE_ASSOC_REQ 0x0000 #define IEEE80211_STYPE_ASSOC_RESP 0x0010 #define IEEE80211_STYPE_REASSOC_REQ 0x0020 #define IEEE80211_STYPE_REASSOC_RESP 0x0030 #define IEEE80211_STYPE_PROBE_REQ 0x0040 #define IEEE80211_STYPE_PROBE_RESP 0x0050 #define IEEE80211_STYPE_BEACON 0x0080 #define IEEE80211_STYPE_ATIM 0x0090 #define IEEE80211_STYPE_DISASSOC 0x00A0 #define IEEE80211_STYPE_AUTH 0x00B0 #define IEEE80211_STYPE_DEAUTH 0x00C0 #define IEEE80211_STYPE_ACTION 0x00D0 /* control */ #define IEEE80211_STYPE_PSPOLL 0x00A0 #define IEEE80211_STYPE_RTS 0x00B0 #define IEEE80211_STYPE_CTS 0x00C0 #define IEEE80211_STYPE_ACK 0x00D0 #define IEEE80211_STYPE_CFEND 0x00E0 #define IEEE80211_STYPE_CFENDACK 0x00F0 /* data */ #define IEEE80211_STYPE_DATA 0x0000 #define IEEE80211_STYPE_DATA_CFACK 0x0010 #define IEEE80211_STYPE_DATA_CFPOLL 0x0020 #define IEEE80211_STYPE_DATA_CFACKPOLL 0x0030 #define IEEE80211_STYPE_NULLFUNC 0x0040 #define IEEE80211_STYPE_CFACK 0x0050 #define IEEE80211_STYPE_CFPOLL 0x0060 #define IEEE80211_STYPE_CFACKPOLL 0x0070 #define IEEE80211_STYPE_QOS_DATA 0x0080 #define IEEE80211_STYPE_QOS_DATA_CFACK 0x0090 #define IEEE80211_STYPE_QOS_DATA_CFPOLL 0x00A0 #define IEEE80211_STYPE_QOS_DATA_CFACKPOLL 0x00B0 #define IEEE80211_STYPE_QOS_NULLFUNC 0x00C0 #define IEEE80211_STYPE_QOS_CFACK 0x00D0 #define IEEE80211_STYPE_QOS_CFPOLL 0x00E0 #define IEEE80211_STYPE_QOS_CFACKPOLL 0x00F0 /* miscellaneous IEEE 802.11 constants */ #define IEEE80211_MAX_FRAG_THRESHOLD 2346 #define IEEE80211_MAX_RTS_THRESHOLD 2347 #define IEEE80211_MAX_AID 2007 #define IEEE80211_MAX_TIM_LEN 251 struct ieee80211_hdr { __le16 frame_control; __le16 duration_id; u8 addr1[6]; u8 addr2[6]; u8 addr3[6]; __le16 seq_ctrl; u8 addr4[6]; } __attribute__ ((packed)); /* return a pointer to the source address (SA) */ static inline u8 *ieee80211_get_SA(struct ieee80211_hdr *hdr) { u8 *raw = (u8 *) hdr; u8 tofrom = (*(raw+1)) & 3; /* get the TODS and FROMDS bits */ switch (tofrom) { case 2: return hdr->addr3; case 3: return hdr->addr4; } return hdr->addr2; } /* return a pointer to the destination address (DA) */ static inline u8 *ieee80211_get_DA(struct ieee80211_hdr *hdr) { u8 *raw = (u8 *) hdr; u8 to_ds = (*(raw+1)) & 1; /* get the TODS bit */ if (to_ds) return hdr->addr3; return hdr->addr1; } static inline int ieee80211_get_morefrag(struct ieee80211_hdr *hdr) { return (le16_to_cpu(hdr->frame_control) & IEEE80211_FCTL_MOREFRAGS) != 0; } #define MAC_FMT "%02x:%02x:%02x:%02x:%02x:%02x" #define MAC_ARG(x) ((u8*)(x))[0], ((u8*)(x))[1], ((u8*)(x))[2], \ ((u8*)(x))[3], ((u8*)(x))[4], ((u8*)(x))[5] #endif /* D80211_H */