From 1c466b799b7eab538286e948516e3f16720a3dd1 Mon Sep 17 00:00:00 2001 From: blogic Date: Tue, 1 Feb 2011 14:26:47 +0000 Subject: [uboot-lantiq] * rework the arcadyan sku support * adds a few new boards and switches git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25273 3c298f89-4303-0410-b956-a3cf2f4a3e73 --- package/uboot-lantiq/files/board/arcadyan/Makefile | 46 ++ .../files/board/arcadyan/arv4518/Makefile | 47 -- .../files/board/arcadyan/arv4518/arv4518.c | 334 --------- .../files/board/arcadyan/arv4518/config.mk | 60 -- .../files/board/arcadyan/arv4518/ddr_settings.h | 50 -- .../files/board/arcadyan/arv4518/lowlevel_init.S | 622 ---------------- .../files/board/arcadyan/arv4518/pmuenable.S | 48 -- .../files/board/arcadyan/arv4518/u-boot.lds | 70 -- .../files/board/arcadyan/arv752DWP22/Makefile | 47 -- .../files/board/arcadyan/arv752DWP22/arv752.c | 325 -------- .../files/board/arcadyan/arv752DWP22/athrs26_phy.c | 814 --------------------- .../files/board/arcadyan/arv752DWP22/athrs26_phy.h | 134 ---- .../files/board/arcadyan/arv752DWP22/config.mk | 60 -- .../board/arcadyan/arv752DWP22/ddr_settings.h | 50 -- .../arcadyan/arv752DWP22/ddr_settings_psc_166.h | 51 -- .../board/arcadyan/arv752DWP22/lowlevel_init.S | 622 ---------------- .../files/board/arcadyan/arv752DWP22/pmuenable.S | 48 -- .../files/board/arcadyan/arv752DWP22/u-boot.lds | 70 -- .../files/board/arcadyan/athrs26_phy.c | 814 +++++++++++++++++++++ .../files/board/arcadyan/athrs26_phy.h | 134 ++++ package/uboot-lantiq/files/board/arcadyan/board.c | 406 ++++++++++ .../uboot-lantiq/files/board/arcadyan/config.mk | 60 ++ .../files/board/arcadyan/ddr_settings.h | 50 ++ .../files/board/arcadyan/ddr_settings_psc_166.h | 51 ++ .../files/board/arcadyan/ddr_settings_qimonda.h | 50 ++ .../files/board/arcadyan/lowlevel_init.S | 622 ++++++++++++++++ .../uboot-lantiq/files/board/arcadyan/pmuenable.S | 48 ++ .../uboot-lantiq/files/board/arcadyan/u-boot.lds | 70 ++ .../files/include/configs/arcadyan-common.h | 138 ++++ .../uboot-lantiq/files/include/configs/arv4518.h | 154 +--- .../uboot-lantiq/files/include/configs/arv452c.h | 14 + .../uboot-lantiq/files/include/configs/arv752DPW.h | 20 + .../files/include/configs/arv752DPW22.h | 20 + .../files/include/configs/arv752DWP22.h | 152 ---- .../files/include/configs/ifx-common.h | 2 +- 35 files changed, 2552 insertions(+), 3751 deletions(-) create mode 100644 package/uboot-lantiq/files/board/arcadyan/Makefile delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv4518/Makefile delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv4518/arv4518.c delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv4518/config.mk delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv4518/ddr_settings.h delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv4518/lowlevel_init.S delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv4518/pmuenable.S delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv4518/u-boot.lds delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/Makefile delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/arv752.c delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/athrs26_phy.c delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/athrs26_phy.h delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/config.mk delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/ddr_settings.h delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/ddr_settings_psc_166.h delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/lowlevel_init.S delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/pmuenable.S delete mode 100644 package/uboot-lantiq/files/board/arcadyan/arv752DWP22/u-boot.lds create mode 100644 package/uboot-lantiq/files/board/arcadyan/athrs26_phy.c create mode 100644 package/uboot-lantiq/files/board/arcadyan/athrs26_phy.h create mode 100644 package/uboot-lantiq/files/board/arcadyan/board.c create mode 100644 package/uboot-lantiq/files/board/arcadyan/config.mk create mode 100644 package/uboot-lantiq/files/board/arcadyan/ddr_settings.h create mode 100644 package/uboot-lantiq/files/board/arcadyan/ddr_settings_psc_166.h create mode 100644 package/uboot-lantiq/files/board/arcadyan/ddr_settings_qimonda.h create mode 100644 package/uboot-lantiq/files/board/arcadyan/lowlevel_init.S create mode 100644 package/uboot-lantiq/files/board/arcadyan/pmuenable.S create mode 100644 package/uboot-lantiq/files/board/arcadyan/u-boot.lds create mode 100644 package/uboot-lantiq/files/include/configs/arcadyan-common.h create mode 100644 package/uboot-lantiq/files/include/configs/arv452c.h create mode 100644 package/uboot-lantiq/files/include/configs/arv752DPW.h create mode 100644 package/uboot-lantiq/files/include/configs/arv752DPW22.h delete mode 100644 package/uboot-lantiq/files/include/configs/arv752DWP22.h (limited to 'package/uboot-lantiq/files') diff --git a/package/uboot-lantiq/files/board/arcadyan/Makefile b/package/uboot-lantiq/files/board/arcadyan/Makefile new file mode 100644 index 0000000000..fb9027c655 --- /dev/null +++ b/package/uboot-lantiq/files/board/arcadyan/Makefile @@ -0,0 +1,46 @@ +# +# (C) Copyright 2003-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += board.o athrs26_phy.o + +SOBJS = lowlevel_init.o pmuenable.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/package/uboot-lantiq/files/board/arcadyan/arv4518/Makefile b/package/uboot-lantiq/files/board/arcadyan/arv4518/Makefile deleted file mode 100644 index 61f383b8dd..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv4518/Makefile +++ /dev/null @@ -1,47 +0,0 @@ -# -# (C) Copyright 2003-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).a - -#COBJS := $(BOARD).o -COBJS-y += arv4518.o - -SOBJS = lowlevel_init.o pmuenable.o - -SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS-y)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(obj).depend $(OBJS) $(SOBJS) - $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/package/uboot-lantiq/files/board/arcadyan/arv4518/arv4518.c b/package/uboot-lantiq/files/board/arcadyan/arv4518/arv4518.c deleted file mode 100644 index c015dd7014..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv4518/arv4518.c +++ /dev/null @@ -1,334 +0,0 @@ -/* - * (C) Copyright 2003 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2010 - * Thomas Langer, Ralph Hempel - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#if defined(CONFIG_CMD_HTTPD) -#include -#endif -#if defined(CONFIG_PCI) -#include -#endif - -extern ulong ifx_get_ddr_hz(void); -extern ulong ifx_get_cpuclk(void); - -/* IDs and registers of known external switches */ -#define ID_RTL8306 0x5988 -#define CONFIG_EXTRA_SWITCH 1 -void _machine_restart(void) -{ - *DANUBE_RCU_RST_REQ |=1<<30; -} - -#ifdef CONFIG_SYS_RAMBOOT -phys_size_t initdram(int board_type) -{ - return get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM); -} -#elif defined(CONFIG_USE_DDR_RAM) -phys_size_t initdram(int board_type) -{ - return (CONFIG_SYS_MAX_RAM); -} -#else - -static ulong max_sdram_size(void) /* per Chip Select */ -{ - /* The only supported SDRAM data width is 16bit. - */ -#define CFG_DW 4 - - /* The only supported number of SDRAM banks is 4. - */ -#define CFG_NB 4 - - ulong cfgpb0 = *DANUBE_SDRAM_MC_CFGPB0; - int cols = cfgpb0 & 0xF; - int rows = (cfgpb0 & 0xF0) >> 4; - ulong size = (1 << (rows + cols)) * CFG_DW * CFG_NB; - - return size; -} - -/* - * Check memory range for valid RAM. A simple memory test determines - * the actually available RAM size between addresses `base' and - * `base + maxsize'. - */ - -static long int dram_size(long int *base, long int maxsize) -{ - volatile long int *addr; - ulong cnt, val; - ulong save[32]; /* to make test non-destructive */ - unsigned char i = 0; - - for (cnt = (maxsize / sizeof (long)) >> 1; cnt > 0; cnt >>= 1) { - addr = base + cnt; /* pointer arith! */ - - save[i++] = *addr; - *addr = ~cnt; - } - - /* write 0 to base address */ - addr = base; - save[i] = *addr; - *addr = 0; - - /* check at base address */ - if ((val = *addr) != 0) { - *addr = save[i]; - return (0); - } - - for (cnt = 1; cnt < maxsize / sizeof (long); cnt <<= 1) { - addr = base + cnt; /* pointer arith! */ - - val = *addr; - *addr = save[--i]; - - if (val != (~cnt)) { - return (cnt * sizeof (long)); - } - } - return (maxsize); -} - -phys_size_t initdram(int board_type) -{ - int rows, cols, best_val = *DANUBE_SDRAM_MC_CFGPB0; - ulong size, max_size = 0; - ulong our_address; - - /* load t9 into our_address */ - asm volatile ("move %0, $25" : "=r" (our_address) :); - - /* Can't probe for RAM size unless we are running from Flash. - * find out whether running from DRAM or Flash. - */ - if (CPHYSADDR(our_address) < CPHYSADDR(PHYS_FLASH_1)) - { - return max_sdram_size(); - } - - for (cols = 0x8; cols <= 0xC; cols++) - { - for (rows = 0xB; rows <= 0xD; rows++) - { - *DANUBE_SDRAM_MC_CFGPB0 = (0x14 << 8) | - (rows << 4) | cols; - size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, - max_sdram_size()); - - if (size > max_size) - { - best_val = *DANUBE_SDRAM_MC_CFGPB0; - max_size = size; - } - } - } - - *DANUBE_SDRAM_MC_CFGPB0 = best_val; - return max_size; -} -#endif - -int checkboard (void) -{ - unsigned long chipid = *DANUBE_MPS_CHIPID; - int part_num; - - puts ("Board: "); - - part_num = DANUBE_MPS_CHIPID_PARTNUM_GET(chipid); - switch (part_num) - { - case 0x129: - case 0x12D: - case 0x12b: - puts("Danube/Twinpass/Vinax-VE "); - break; - default: - printf ("unknown, chip part number 0x%03X ", part_num); - break; - } - printf ("V1.%ld, ", DANUBE_MPS_CHIPID_VERSION_GET(chipid)); - - printf("DDR Speed %ld MHz, ", ifx_get_ddr_hz()/1000000); - printf("CPU Speed %ld MHz\n", ifx_get_cpuclk()/1000000); - - return 0; -} - -#ifdef CONFIG_SKIP_LOWLEVEL_INIT -int board_early_init_f(void) -{ -#ifdef CONFIG_EBU_ADDSEL0 - (*DANUBE_EBU_ADDSEL0) = CONFIG_EBU_ADDSEL0; -#endif -#ifdef CONFIG_EBU_ADDSEL1 - (*DANUBE_EBU_ADDSEL1) = CONFIG_EBU_ADDSEL1; -#endif -#ifdef CONFIG_EBU_ADDSEL2 - (*DANUBE_EBU_ADDSEL2) = CONFIG_EBU_ADDSEL2; -#endif -#ifdef CONFIG_EBU_ADDSEL3 - (*DANUBE_EBU_ADDSEL3) = CONFIG_EBU_ADDSEL3; -#endif -#ifdef CONFIG_EBU_BUSCON0 - (*DANUBE_EBU_BUSCON0) = CONFIG_EBU_BUSCON0; -#endif -#ifdef CONFIG_EBU_BUSCON1 - (*DANUBE_EBU_BUSCON1) = CONFIG_EBU_BUSCON1; -#endif -#ifdef CONFIG_EBU_BUSCON2 - (*DANUBE_EBU_BUSCON2) = CONFIG_EBU_BUSCON2; -#endif -#ifdef CONFIG_EBU_BUSCON3 - (*DANUBE_EBU_BUSCON3) = CONFIG_EBU_BUSCON3; -#endif - - return 0; -} -#endif /* CONFIG_SKIP_LOWLEVEL_INIT */ - - -#ifdef CONFIG_EXTRA_SWITCH -static int external_switch_init(void) -{ - unsigned short chipid; - static char * const name = "lq_cpe_eth"; - - /* earlier no valid response is available, at least on Twinpass & Tantos @ 111MHz, M4530 platform */ - udelay(100000); - - puts("\nsearching for rtl8306 switch ... "); - if (miiphy_read(name, 4, 30, &chipid) == 0) { - puts("s1\n"); - if (chipid == ID_RTL8306) { - puts("found"); - /* set led mode */ - miiphy_write(name, 0, 19, 0xffff); - /* magic */ - miiphy_write(name, 4, 22, 0x877f); - puts("\n"); - return 0; - } - puts("failed\n"); - } - puts("\nno known switch found ... \n"); - - return 0; -} -#endif /* CONFIG_EXTRA_SWITCH */ - -int board_eth_init(bd_t *bis) -{ -#if defined(CONFIG_IFX_ETOP) - uchar enetaddr[6]; - if (!eth_getenv_enetaddr("ethaddr", enetaddr)) - eth_setenv_enetaddr("ethaddr", (uchar *)0xb03f0016); - - *DANUBE_PMU_PWDCR &= 0xFFFFEFDF; - *DANUBE_PMU_PWDCR &=~(1< - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -/* History: - peng liu May 25, 2006, for PLL setting after reset, 05252006 - */ -#include -#include -#include - -#if 0 - -#if defined(CONFIG_USE_DDR_RAM) - -#if defined(CONFIG_USE_DDR_RAM_CFG_111M) -#include "ddr_settings_r111.h" -#define DDR111 -#elif defined(CONFIG_USE_DDR_RAM_CFG_166M) -#include "ddr_settings_r166.h" -#define DDR166 -#elif defined(CONFIG_USE_DDR_RAM_CFG_e111M) -#include "ddr_settings_e111.h" -#define DDR111 -#elif defined(CONFIG_USE_DDR_RAM_CFG_e166M) -#include "ddr_settings_e166.h" -#define DDR166 -#elif defined(CONFIG_USE_DDR_RAM_CFG_promos400) -#include "ddr_settings_PROMOSDDR400.h" -#define DDR166 -#elif defined(CONFIG_USE_DDR_RAM_CFG_samsung166) -#include "ddr_settings_Samsung_166.h" -#define DDR166 -#elif defined(CONFIG_USE_DDR_RAM_CFG_psc166) -#include "ddr_settings_psc_166.h" -#define DDR166 -#else -#warning "missing definition for ddr_settings.h, use default!" -#include "ddr_settings.h" -#endif -#endif /* CONFIG_USE_DDR_RAM */ - -#else - -#include "ddr_settings.h" -#define DDR166 - -#endif - -#if defined(CONFIG_USE_DDR_RAM) && !defined(MC_DC0_VALUE) -#error "missing include of ddr_settings.h" -#endif - -#define EBU_MODUL_BASE 0xBE105300 -#define EBU_CLC(value) 0x0000(value) -#define EBU_CON(value) 0x0010(value) -#define EBU_ADDSEL0(value) 0x0020(value) -#define EBU_ADDSEL1(value) 0x0024(value) -#define EBU_ADDSEL2(value) 0x0028(value) -#define EBU_ADDSEL3(value) 0x002C(value) -#define EBU_BUSCON0(value) 0x0060(value) -#define EBU_BUSCON1(value) 0x0064(value) -#define EBU_BUSCON2(value) 0x0068(value) -#define EBU_BUSCON3(value) 0x006C(value) - -#define MC_MODUL_BASE 0xBF800000 -#define MC_ERRCAUSE(value) 0x0010(value) -#define MC_ERRADDR(value) 0x0020(value) -#define MC_CON(value) 0x0060(value) - -#define MC_SRAM_ENABLE 0x00000004 -#define MC_SDRAM_ENABLE 0x00000002 -#define MC_DDRRAM_ENABLE 0x00000001 - -#define MC_SDR_MODUL_BASE 0xBF800200 -#define MC_IOGP(value) 0x0000(value) -#define MC_CTRLENA(value) 0x0010(value) -#define MC_MRSCODE(value) 0x0020(value) -#define MC_CFGDW(value) 0x0030(value) -#define MC_CFGPB0(value) 0x0040(value) -#define MC_LATENCY(value) 0x0080(value) -#define MC_TREFRESH(value) 0x0090(value) -#define MC_SELFRFSH(value) 0x00A0(value) - -#define MC_DDR_MODUL_BASE 0xBF801000 -#define MC_DC00(value) 0x0000(value) -#define MC_DC01(value) 0x0010(value) -#define MC_DC02(value) 0x0020(value) -#define MC_DC03(value) 0x0030(value) -#define MC_DC04(value) 0x0040(value) -#define MC_DC05(value) 0x0050(value) -#define MC_DC06(value) 0x0060(value) -#define MC_DC07(value) 0x0070(value) -#define MC_DC08(value) 0x0080(value) -#define MC_DC09(value) 0x0090(value) -#define MC_DC10(value) 0x00A0(value) -#define MC_DC11(value) 0x00B0(value) -#define MC_DC12(value) 0x00C0(value) -#define MC_DC13(value) 0x00D0(value) -#define MC_DC14(value) 0x00E0(value) -#define MC_DC15(value) 0x00F0(value) -#define MC_DC16(value) 0x0100(value) -#define MC_DC17(value) 0x0110(value) -#define MC_DC18(value) 0x0120(value) -#define MC_DC19(value) 0x0130(value) -#define MC_DC20(value) 0x0140(value) -#define MC_DC21(value) 0x0150(value) -#define MC_DC22(value) 0x0160(value) -#define MC_DC23(value) 0x0170(value) -#define MC_DC24(value) 0x0180(value) -#define MC_DC25(value) 0x0190(value) -#define MC_DC26(value) 0x01A0(value) -#define MC_DC27(value) 0x01B0(value) -#define MC_DC28(value) 0x01C0(value) -#define MC_DC29(value) 0x01D0(value) -#define MC_DC30(value) 0x01E0(value) -#define MC_DC31(value) 0x01F0(value) -#define MC_DC32(value) 0x0200(value) -#define MC_DC33(value) 0x0210(value) -#define MC_DC34(value) 0x0220(value) -#define MC_DC35(value) 0x0230(value) -#define MC_DC36(value) 0x0240(value) -#define MC_DC37(value) 0x0250(value) -#define MC_DC38(value) 0x0260(value) -#define MC_DC39(value) 0x0270(value) -#define MC_DC40(value) 0x0280(value) -#define MC_DC41(value) 0x0290(value) -#define MC_DC42(value) 0x02A0(value) -#define MC_DC43(value) 0x02B0(value) -#define MC_DC44(value) 0x02C0(value) -#define MC_DC45(value) 0x02D0(value) -#define MC_DC46(value) 0x02E0(value) - -#define RCU_OFFSET 0xBF203000 -#define RCU_RST_REQ (RCU_OFFSET + 0x0010) -#define RCU_STS (RCU_OFFSET + 0x0014) - -#define CGU_OFFSET 0xBF103000 -#define PLL0_CFG (CGU_OFFSET + 0x0004) -#define PLL1_CFG (CGU_OFFSET + 0x0008) -#define PLL2_CFG (CGU_OFFSET + 0x000C) -#define CGU_SYS (CGU_OFFSET + 0x0010) -#define CGU_UPDATE (CGU_OFFSET + 0x0014) -#define IF_CLK (CGU_OFFSET + 0x0018) -#define CGU_SMD (CGU_OFFSET + 0x0020) -#define CGU_CT1SR (CGU_OFFSET + 0x0028) -#define CGU_CT2SR (CGU_OFFSET + 0x002C) -#define CGU_PCMCR (CGU_OFFSET + 0x0030) -#define PCI_CR_PCI (CGU_OFFSET + 0x0034) -#define CGU_OSC_CTRL (CGU_OFFSET + 0x001C) -#define CGU_MIPS_PWR_DWN (CGU_OFFSET + 0x0038) -#define CLK_MEASURE (CGU_OFFSET + 0x003C) - -//05252006 -#define pll0_35MHz_CONFIG 0x9D861059 -#define pll1_35MHz_CONFIG 0x1A260CD9 -#define pll2_35MHz_CONFIG 0x8000f1e5 -#define pll0_36MHz_CONFIG 0x1000125D -#define pll1_36MHz_CONFIG 0x1B1E0C99 -#define pll2_36MHz_CONFIG 0x8002f2a1 -//05252006 - -//06063001-joelin disable the PCI CFRAME mask -start -/*CFRAME is an I/O signal, in the chip, the output CFRAME is selected via GPIO altsel pins, so if you select MII1 RXD1, the CFRAME will not come out. -But the CFRAME input still take the signal from the pad and not disabled when altsel choose other function. So when MII1_RXD1 is low from other device, the EBU interface will be disabled. - -The chip function in such a way that disable the CFRAME mask mean EBU not longer check CFRAME to be the device using the bus. -The side effect is the entire PCI block will see CFRAME low all the time meaning PCI cannot use the bus at all so no more PCI function. -*/ -#define PCI_CR_PR_OFFSET 0xBE105400 -#define PCI_CR_PCI_MOD_REG (PCI_CR_PR_OFFSET + 0x0030) -#define PCI_CONFIG_SPACE 0xB7000000 -#define CS_CFM (PCI_CONFIG_SPACE + 0x6C) -//06063001-joelin disable the PCI CFRAME mask -end - .set noreorder - - -/* - * void ebu_init(void) - */ - .globl ebu_init - .ent ebu_init -ebu_init: - -#if defined(CONFIG_EBU_ADDSEL0) || defined(CONFIG_EBU_ADDSEL1) || \ - defined(CONFIG_EBU_ADDSEL2) || defined(CONFIG_EBU_ADDSEL3) || \ - defined(CONFIG_EBU_BUSCON0) || defined(CONFIG_EBU_BUSCON1) || \ - defined(CONFIG_EBU_BUSCON2) || defined(CONFIG_EBU_BUSCON3) - - li t1, EBU_MODUL_BASE -#if defined(CONFIG_EBU_ADDSEL0) - li t2, CONFIG_EBU_ADDSEL0 - sw t2, EBU_ADDSEL0(t1) -#endif -#if defined(CONFIG_EBU_ADDSEL1) - li t2, CONFIG_EBU_ADDSEL1 - sw t2, EBU_ADDSEL1(t1) -#endif -#if defined(CONFIG_EBU_ADDSEL2) - li t2, CONFIG_EBU_ADDSEL2 - sw t2, EBU_ADDSEL2(t1) -#endif -#if defined(CONFIG_EBU_ADDSEL3) - li t2, CONFIG_EBU_ADDSEL3 - sw t2, EBU_ADDSEL3(t1) -#endif - -#if defined(CONFIG_EBU_BUSCON0) - li t2, CONFIG_EBU_BUSCON0 - sw t2, EBU_BUSCON0(t1) -#endif -#if defined(CONFIG_EBU_BUSCON1) - li t2, CONFIG_EBU_BUSCON1 - sw t2, EBU_BUSCON1(t1) -#endif -#if defined(CONFIG_EBU_BUSCON2) - li t2, CONFIG_EBU_BUSCON2 - sw t2, EBU_BUSCON2(t1) -#endif -#if defined(CONFIG_EBU_BUSCON3) - li t2, CONFIG_EBU_BUSCON3 - sw t2, EBU_BUSCON3(t1) -#endif - -#endif - - j ra - nop - - .end ebu_init - - -/* - * void cgu_init(long) - * - * a0 has the clock value - */ - .globl cgu_init - .ent cgu_init -cgu_init: - li t2, CGU_SYS - lw t2,0(t2) - beq t2,a0,freq_up2date - nop - - li t2, RCU_STS - lw t2, 0(t2) - and t2,0x00020000 - beq t2,0x00020000,boot_36MHZ - nop -//05252006 - li t1, PLL0_CFG - li t2, pll0_35MHz_CONFIG - sw t2,0(t1) - li t1, PLL1_CFG - li t2, pll1_35MHz_CONFIG - sw t2,0(t1) - li t1, PLL2_CFG - li t2, pll2_35MHz_CONFIG - sw t2,0(t1) - li t1, CGU_SYS - sw a0,0(t1) - li t1, RCU_RST_REQ - li t2, 0x40000008 - sw t2,0(t1) - b wait_reset - nop -boot_36MHZ: - li t1, PLL0_CFG - li t2, pll0_36MHz_CONFIG - sw t2,0(t1) - li t1, PLL1_CFG - li t2, pll1_36MHz_CONFIG - sw t2,0(t1) - li t1, PLL2_CFG - li t2, pll2_36MHz_CONFIG - sw t2,0(t1) - li t1, CGU_SYS - sw a0,0(t1) - li t1, RCU_RST_REQ - li t2, 0x40000008 - sw t2,0(t1) -//05252006 - -wait_reset: - b wait_reset - nop -freq_up2date: - j ra - nop - - .end cgu_init - -#ifndef CONFIG_USE_DDR_RAM -/* - * void sdram_init(long) - * - * a0 has the clock value - */ - .globl sdram_init - .ent sdram_init -sdram_init: - - /* SDRAM Initialization - */ - li t1, MC_MODUL_BASE - - /* Clear Error log registers */ - sw zero, MC_ERRCAUSE(t1) - sw zero, MC_ERRADDR(t1) - - /* Enable SDRAM module in memory controller */ - li t3, MC_SDRAM_ENABLE - lw t2, MC_CON(t1) - or t3, t2, t3 - sw t3, MC_CON(t1) - - li t1, MC_SDR_MODUL_BASE - - /* disable the controller */ - li t2, 0 - sw t2, MC_CTRLENA(t1) - - li t2, 0x822 - sw t2, MC_IOGP(t1) - - li t2, 0x2 - sw t2, MC_CFGDW(t1) - - /* Set CAS Latency */ - li t2, 0x00000020 - sw t2, MC_MRSCODE(t1) - - /* Set CS0 to SDRAM parameters */ - li t2, 0x000014d8 - sw t2, MC_CFGPB0(t1) - - /* Set SDRAM latency parameters */ - li t2, 0x00036325; /* BC PC100 */ - sw t2, MC_LATENCY(t1) - - /* Set SDRAM refresh rate */ - li t2, 0x00000C30 - sw t2, MC_TREFRESH(t1) - - /* Clear Power-down registers */ - sw zero, MC_SELFRFSH(t1) - - /* Finally enable the controller */ - li t2, 1 - sw t2, MC_CTRLENA(t1) - - j ra - nop - - .end sdram_init - -#endif /* !CONFIG_USE_DDR_RAM */ - -#ifdef CONFIG_USE_DDR_RAM -/* - * void ddrram_init(long) - * - * a0 has the clock value - */ - .globl ddrram_init - .ent ddrram_init -ddrram_init: - - /* DDR-DRAM Initialization - */ - li t1, MC_MODUL_BASE - - /* Clear Error log registers */ - sw zero, MC_ERRCAUSE(t1) - sw zero, MC_ERRADDR(t1) - - /* Enable DDR module in memory controller */ - li t3, MC_DDRRAM_ENABLE - lw t2, MC_CON(t1) - or t3, t2, t3 - sw t3, MC_CON(t1) - - li t1, MC_DDR_MODUL_BASE - - /* Write configuration to DDR controller registers */ - li t2, MC_DC0_VALUE - sw t2, MC_DC00(t1) - - li t2, MC_DC1_VALUE - sw t2, MC_DC01(t1) - - li t2, MC_DC2_VALUE - sw t2, MC_DC02(t1) - - li t2, MC_DC3_VALUE - sw t2, MC_DC03(t1) - - li t2, MC_DC4_VALUE - sw t2, MC_DC04(t1) - - li t2, MC_DC5_VALUE - sw t2, MC_DC05(t1) - - li t2, MC_DC6_VALUE - sw t2, MC_DC06(t1) - - li t2, MC_DC7_VALUE - sw t2, MC_DC07(t1) - - li t2, MC_DC8_VALUE - sw t2, MC_DC08(t1) - - li t2, MC_DC9_VALUE - sw t2, MC_DC09(t1) - - li t2, MC_DC10_VALUE - sw t2, MC_DC10(t1) - - li t2, MC_DC11_VALUE - sw t2, MC_DC11(t1) - - li t2, MC_DC12_VALUE - sw t2, MC_DC12(t1) - - li t2, MC_DC13_VALUE - sw t2, MC_DC13(t1) - - li t2, MC_DC14_VALUE - sw t2, MC_DC14(t1) - - li t2, MC_DC15_VALUE - sw t2, MC_DC15(t1) - - li t2, MC_DC16_VALUE - sw t2, MC_DC16(t1) - - li t2, MC_DC17_VALUE - sw t2, MC_DC17(t1) - - li t2, MC_DC18_VALUE - sw t2, MC_DC18(t1) - - li t2, MC_DC19_VALUE - sw t2, MC_DC19(t1) - - li t2, MC_DC20_VALUE - sw t2, MC_DC20(t1) - - li t2, MC_DC21_VALUE - sw t2, MC_DC21(t1) - - li t2, MC_DC22_VALUE - sw t2, MC_DC22(t1) - - li t2, MC_DC23_VALUE - sw t2, MC_DC23(t1) - - li t2, MC_DC24_VALUE - sw t2, MC_DC24(t1) - - li t2, MC_DC25_VALUE - sw t2, MC_DC25(t1) - - li t2, MC_DC26_VALUE - sw t2, MC_DC26(t1) - - li t2, MC_DC27_VALUE - sw t2, MC_DC27(t1) - - li t2, MC_DC28_VALUE - sw t2, MC_DC28(t1) - - li t2, MC_DC29_VALUE - sw t2, MC_DC29(t1) - - li t2, MC_DC30_VALUE - sw t2, MC_DC30(t1) - - li t2, MC_DC31_VALUE - sw t2, MC_DC31(t1) - - li t2, MC_DC32_VALUE - sw t2, MC_DC32(t1) - - li t2, MC_DC33_VALUE - sw t2, MC_DC33(t1) - - li t2, MC_DC34_VALUE - sw t2, MC_DC34(t1) - - li t2, MC_DC35_VALUE - sw t2, MC_DC35(t1) - - li t2, MC_DC36_VALUE - sw t2, MC_DC36(t1) - - li t2, MC_DC37_VALUE - sw t2, MC_DC37(t1) - - li t2, MC_DC38_VALUE - sw t2, MC_DC38(t1) - - li t2, MC_DC39_VALUE - sw t2, MC_DC39(t1) - - li t2, MC_DC40_VALUE - sw t2, MC_DC40(t1) - - li t2, MC_DC41_VALUE - sw t2, MC_DC41(t1) - - li t2, MC_DC42_VALUE - sw t2, MC_DC42(t1) - - li t2, MC_DC43_VALUE - sw t2, MC_DC43(t1) - - li t2, MC_DC44_VALUE - sw t2, MC_DC44(t1) - - li t2, MC_DC45_VALUE - sw t2, MC_DC45(t1) - - li t2, MC_DC46_VALUE - sw t2, MC_DC46(t1) - - li t2, 0x00000100 - sw t2, MC_DC03(t1) - - j ra - nop - - .end ddrram_init -#endif /* CONFIG_USE_DDR_RAM */ - - .globl lowlevel_init - .ent lowlevel_init -lowlevel_init: - /* EBU, CGU and SDRAM/DDR-RAM Initialization. - */ - move t0, ra - /* We rely on the fact that non of the following ..._init() functions - * modify t0 - */ -#if defined(CONFIG_SYS_EBU_BOOT) -#if defined(DDR166) - /* 0xe8 means CPU0/CPU1 333M, DDR 167M, FPI 83M, PPE 240M */ - li a0,0xe8 -#elif defined(DDR133) - /* 0xe9 means CPU0/CPU1 333M, DDR 133M, FPI 83M, PPE 240M */ - li a0,0xe9 -#else /* defined(DDR111) */ - /* 0xea means CPU0/CPU1 333M, DDR 111M, FPI 83M, PPE 240M */ - li a0,0xea -#endif - bal cgu_init - nop -#endif /* CONFIG_SYS_EBU_BOOT */ - - bal ebu_init - nop - -//06063001-joelin disable the PCI CFRAME mask-start -#ifdef DISABLE_CFRAME - li t1, PCI_CR_PCI //mw bf103034 80000000 - li t2, 0x80000000 - sw t2,0(t1) - - li t1, PCI_CR_PCI_MOD_REG //mw be105430 103 - li t2, 0x103 - sw t2,0(t1) - - li t1, CS_CFM //mw b700006c 0 - li t2, 0x00 - sw t2, 0(t1) - - li t1, PCI_CR_PCI_MOD_REG //mw be105430 103 - li t2, 0x1000103 - sw t2, 0(t1) -#endif -//06063001-joelin disable the PCI CFRAME mask-end - -#ifdef CONFIG_SYS_EBU_BOOT -#ifndef CONFIG_SYS_RAMBOOT -#ifdef CONFIG_USE_DDR_RAM - bal ddrram_init - nop -#else - bal sdram_init - nop -#endif -#endif /* CONFIG_SYS_RAMBOOT */ -#endif /* CONFIG_SYS_EBU_BOOT */ - - move ra, t0 - j ra - nop - - .end lowlevel_init diff --git a/package/uboot-lantiq/files/board/arcadyan/arv4518/pmuenable.S b/package/uboot-lantiq/files/board/arcadyan/arv4518/pmuenable.S deleted file mode 100644 index e0d7971d89..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv4518/pmuenable.S +++ /dev/null @@ -1,48 +0,0 @@ -/* - * Power Management unit initialization code for AMAZON development board. - * - * Copyright (c) 2003 Ou Ke, Infineon. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include - -#define PMU_PWDCR 0xBF10201C -#define PMU_SR 0xBF102020 - - .globl pmuenable - -pmuenable: - li t0, PMU_PWDCR - li t1, 0x2 /* enable everything */ - sw t1, 0(t0) -#if 0 -1: - li t0, PMU_SR - lw t2, 0(t0) - bne t1, t2, 1b - nop -#endif - j ra - nop - - diff --git a/package/uboot-lantiq/files/board/arcadyan/arv4518/u-boot.lds b/package/uboot-lantiq/files/board/arcadyan/arv4518/u-boot.lds deleted file mode 100644 index 9a6cd1b8a3..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv4518/u-boot.lds +++ /dev/null @@ -1,70 +0,0 @@ -/* - * (C) Copyright 2003 - * Wolfgang Denk Engineering, - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* -OUTPUT_FORMAT("elf32-bigmips", "elf32-bigmips", "elf32-bigmips") -*/ -OUTPUT_FORMAT("elf32-tradbigmips", "elf32-tradbigmips", "elf32-tradbigmips") -OUTPUT_ARCH(mips) -ENTRY(_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN(4); - .text : - { - *(.text) - } - - . = ALIGN(4); - .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) } - - . = ALIGN(4); - .data : { *(.data) } - - . = .; - _gp = ALIGN(16) + 0x7ff0; - - .got : { - __got_start = .; - *(.got) - __got_end = .; - } - - .sdata : { *(.sdata) } - - .u_boot_cmd : { - __u_boot_cmd_start = .; - *(.u_boot_cmd) - __u_boot_cmd_end = .; - } - - uboot_end_data = .; - num_got_entries = (__got_end - __got_start) >> 2; - - . = ALIGN(4); - .sbss (NOLOAD) : { *(.sbss) } - .bss (NOLOAD) : { *(.bss) . = ALIGN(4); } - uboot_end = .; -} diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/Makefile b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/Makefile deleted file mode 100644 index 2d0115f8ed..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/Makefile +++ /dev/null @@ -1,47 +0,0 @@ -# -# (C) Copyright 2003-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).a - -#COBJS := $(BOARD).o -COBJS-y += arv752.o athrs26_phy.o - -SOBJS = lowlevel_init.o pmuenable.o - -SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS-y)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(obj).depend $(OBJS) $(SOBJS) - $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/arv752.c b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/arv752.c deleted file mode 100644 index 5b68de9589..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/arv752.c +++ /dev/null @@ -1,325 +0,0 @@ -/* - * (C) Copyright 2003 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2010 - * Thomas Langer, Ralph Hempel - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#if defined(CONFIG_CMD_HTTPD) -#include -#endif -#if defined(CONFIG_PCI) -#include -#endif -#include "athrs26_phy.h" - -extern ulong ifx_get_ddr_hz(void); -extern ulong ifx_get_cpuclk(void); - -/* IDs and registers of known external switches */ -void _machine_restart(void) -{ - *DANUBE_RCU_RST_REQ |=1<<30; -} - -#ifdef CONFIG_SYS_RAMBOOT -phys_size_t initdram(int board_type) -{ - return get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM); -} -#elif defined(CONFIG_USE_DDR_RAM) -phys_size_t initdram(int board_type) -{ - return (CONFIG_SYS_MAX_RAM); -} -#else - -static ulong max_sdram_size(void) /* per Chip Select */ -{ - /* The only supported SDRAM data width is 16bit. - */ -#define CFG_DW 4 - - /* The only supported number of SDRAM banks is 4. - */ -#define CFG_NB 4 - - ulong cfgpb0 = *DANUBE_SDRAM_MC_CFGPB0; - int cols = cfgpb0 & 0xF; - int rows = (cfgpb0 & 0xF0) >> 4; - ulong size = (1 << (rows + cols)) * CFG_DW * CFG_NB; - - return size; -} - -/* - * Check memory range for valid RAM. A simple memory test determines - * the actually available RAM size between addresses `base' and - * `base + maxsize'. - */ - -static long int dram_size(long int *base, long int maxsize) -{ - volatile long int *addr; - ulong cnt, val; - ulong save[32]; /* to make test non-destructive */ - unsigned char i = 0; - - for (cnt = (maxsize / sizeof (long)) >> 1; cnt > 0; cnt >>= 1) { - addr = base + cnt; /* pointer arith! */ - - save[i++] = *addr; - *addr = ~cnt; - } - - /* write 0 to base address */ - addr = base; - save[i] = *addr; - *addr = 0; - - /* check at base address */ - if ((val = *addr) != 0) { - *addr = save[i]; - return (0); - } - - for (cnt = 1; cnt < maxsize / sizeof (long); cnt <<= 1) { - addr = base + cnt; /* pointer arith! */ - - val = *addr; - *addr = save[--i]; - - if (val != (~cnt)) { - return (cnt * sizeof (long)); - } - } - return (maxsize); -} - -phys_size_t initdram(int board_type) -{ - int rows, cols, best_val = *DANUBE_SDRAM_MC_CFGPB0; - ulong size, max_size = 0; - ulong our_address; - - /* load t9 into our_address */ - asm volatile ("move %0, $25" : "=r" (our_address) :); - - /* Can't probe for RAM size unless we are running from Flash. - * find out whether running from DRAM or Flash. - */ - if (CPHYSADDR(our_address) < CPHYSADDR(PHYS_FLASH_1)) - { - return max_sdram_size(); - } - - for (cols = 0x8; cols <= 0xC; cols++) - { - for (rows = 0xB; rows <= 0xD; rows++) - { - *DANUBE_SDRAM_MC_CFGPB0 = (0x14 << 8) | - (rows << 4) | cols; - size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, - max_sdram_size()); - - if (size > max_size) - { - best_val = *DANUBE_SDRAM_MC_CFGPB0; - max_size = size; - } - } - } - - *DANUBE_SDRAM_MC_CFGPB0 = best_val; - return max_size; -} -#endif - -int checkboard (void) -{ - unsigned long chipid = *DANUBE_MPS_CHIPID; - int part_num; - - puts ("Board: ARV75DW22 - Easybox 803\n"); - puts ("SoC: "); - - part_num = DANUBE_MPS_CHIPID_PARTNUM_GET(chipid); - switch (part_num) - { - case 0x129: - case 0x12D: - case 0x12b: - puts("Danube/Twinpass/Vinax-VE "); - break; - default: - printf ("unknown, chip part number 0x%03X ", part_num); - break; - } - printf ("V1.%ld, ", DANUBE_MPS_CHIPID_VERSION_GET(chipid)); - - printf("DDR Speed %ld MHz, ", ifx_get_ddr_hz()/1000000); - printf("CPU Speed %ld MHz\n", ifx_get_cpuclk()/1000000); - - return 0; -} - -#ifdef CONFIG_SKIP_LOWLEVEL_INIT -int board_early_init_f(void) -{ -#ifdef CONFIG_EBU_ADDSEL0 - (*DANUBE_EBU_ADDSEL0) = CONFIG_EBU_ADDSEL0; -#endif -#ifdef CONFIG_EBU_ADDSEL1 - (*DANUBE_EBU_ADDSEL1) = CONFIG_EBU_ADDSEL1; -#endif -#ifdef CONFIG_EBU_ADDSEL2 - (*DANUBE_EBU_ADDSEL2) = CONFIG_EBU_ADDSEL2; -#endif -#ifdef CONFIG_EBU_ADDSEL3 - (*DANUBE_EBU_ADDSEL3) = CONFIG_EBU_ADDSEL3; -#endif -#ifdef CONFIG_EBU_BUSCON0 - (*DANUBE_EBU_BUSCON0) = CONFIG_EBU_BUSCON0; -#endif -#ifdef CONFIG_EBU_BUSCON1 - (*DANUBE_EBU_BUSCON1) = CONFIG_EBU_BUSCON1; -#endif -#ifdef CONFIG_EBU_BUSCON2 - (*DANUBE_EBU_BUSCON2) = CONFIG_EBU_BUSCON2; -#endif -#ifdef CONFIG_EBU_BUSCON3 - (*DANUBE_EBU_BUSCON3) = CONFIG_EBU_BUSCON3; -#endif - - return 0; -} -#endif /* CONFIG_SKIP_LOWLEVEL_INIT */ - - -#ifdef CONFIG_EXTRA_SWITCH -static int external_switch_init(void) -{ - // switch reset pin on arv752 - *DANUBE_GPIO_P1_ALTSEL0 &= ~8; - *DANUBE_GPIO_P1_ALTSEL1 &= ~8; - *DANUBE_GPIO_P1_OD |= 8; - *DANUBE_GPIO_P1_DIR |= 8; - *DANUBE_GPIO_P1_OUT |= 8; - - puts("initializing ar8216 switch... "); - if (athrs26_phy_setup(0)==0) { - printf("initialized\n"); - return 0; - } - puts("failed ... \n"); - return 0; -} -#endif /* CONFIG_EXTRA_SWITCH */ - -int board_eth_init(bd_t *bis) -{ -#if defined(CONFIG_IFX_ETOP) - uchar enetaddr[6]; - if (!eth_getenv_enetaddr("ethaddr", enetaddr)) - eth_setenv_enetaddr("ethaddr", (uchar *)0xb03f0016); - - *DANUBE_PMU_PWDCR &= 0xFFFFEFDF; - *DANUBE_PMU_PWDCR &=~(1< -#include -#include -#include -//#include "phy.h" -//#include "ar7100_soc.h" -#include "athrs26_phy.h" - -#define phy_reg_read(base, addr, reg, datap) \ - miiphy_read("lq_cpe_eth", addr, reg, datap); -#define phy_reg_write(base, addr, reg, data) \ - miiphy_write("lq_cpe_eth", addr, reg, data); - - -/* PHY selections and access functions */ - -typedef enum { - PHY_SRCPORT_INFO, - PHY_PORTINFO_SIZE, -} PHY_CAP_TYPE; - -typedef enum { - PHY_SRCPORT_NONE, - PHY_SRCPORT_VLANTAG, - PHY_SRCPORT_TRAILER, -} PHY_SRCPORT_TYPE; - -#ifdef DEBUG -#define DRV_DEBUG 1 -#endif -//#define DRV_DEBUG 1 - -#define DRV_DEBUG_PHYERROR 0x00000001 -#define DRV_DEBUG_PHYCHANGE 0x00000002 -#define DRV_DEBUG_PHYSETUP 0x00000004 - -#if DRV_DEBUG -int athrPhyDebug = DRV_DEBUG_PHYERROR|DRV_DEBUG_PHYCHANGE|DRV_DEBUG_PHYSETUP; - -#define DRV_LOG(FLG, X0, X1, X2, X3, X4, X5, X6) \ -{ \ - if (athrPhyDebug & (FLG)) { \ - logMsg(X0, X1, X2, X3, X4, X5, X6); \ - } \ -} - -#define DRV_MSG(x,a,b,c,d,e,f) \ - logMsg(x,a,b,c,d,e,f) - -#define DRV_PRINT(FLG, X) \ -{ \ - if (athrPhyDebug & (FLG)) { \ - printf X; \ - } \ -} - -#else /* !DRV_DEBUG */ -#define DRV_LOG(DBG_SW, X0, X1, X2, X3, X4, X5, X6) -#define DRV_MSG(x,a,b,c,d,e,f) -#define DRV_PRINT(DBG_SW,X) -#endif - -#define ATHR_LAN_PORT_VLAN 1 -#define ATHR_WAN_PORT_VLAN 2 - -#define ENET_UNIT_LAN 0 - -#define TRUE 1 -#define FALSE 0 - -#define ATHR_PHY0_ADDR 0x0 -#define ATHR_PHY1_ADDR 0x1 -#define ATHR_PHY2_ADDR 0x2 -#define ATHR_PHY3_ADDR 0x3 -#define ATHR_PHY4_ADDR 0x4 - -/* - * Track per-PHY port information. - */ -typedef struct { - BOOL isEnetPort; /* normal enet port */ - BOOL isPhyAlive; /* last known state of link */ - int ethUnit; /* MAC associated with this phy port */ - uint32_t phyBase; - uint32_t phyAddr; /* PHY registers associated with this phy port */ - uint32_t VLANTableSetting; /* Value to be written to VLAN table */ -} athrPhyInfo_t; - -/* - * Per-PHY information, indexed by PHY unit number. - */ -static athrPhyInfo_t athrPhyInfo[] = { - {TRUE, /* phy port 0 -- LAN port 0 */ - FALSE, - ENET_UNIT_LAN, - 0, - ATHR_PHY0_ADDR, - ATHR_LAN_PORT_VLAN - }, - - {TRUE, /* phy port 1 -- LAN port 1 */ - FALSE, - ENET_UNIT_LAN, - 0, - ATHR_PHY1_ADDR, - ATHR_LAN_PORT_VLAN - }, - - {TRUE, /* phy port 2 -- LAN port 2 */ - FALSE, - ENET_UNIT_LAN, - 0, - ATHR_PHY2_ADDR, - ATHR_LAN_PORT_VLAN - }, - - {TRUE, /* phy port 3 -- LAN port 3 */ - FALSE, - ENET_UNIT_LAN, - 0, - ATHR_PHY3_ADDR, - ATHR_LAN_PORT_VLAN - }, - - {TRUE, /* phy port 4 -- WAN port or LAN port 4 */ - FALSE, - 1, - 0, - ATHR_PHY4_ADDR, - ATHR_LAN_PORT_VLAN /* Send to all ports */ - }, - - {FALSE, /* phy port 5 -- CPU port (no RJ45 connector) */ - TRUE, - ENET_UNIT_LAN, - 0, - 0x00, - ATHR_LAN_PORT_VLAN /* Send to all ports */ - }, -}; - -#ifdef CFG_ATHRHDR_EN -typedef struct { - uint8_t data[ATHRHDR_MAX_DATA]; - uint8_t len; - uint32_t seq; -} cmd_resp_t; - -typedef struct { - uint16_t reg_addr; - uint16_t cmd_len; - uint8_t *reg_data; -}cmd_write_t; - -static cmd_write_t cmd_write,cmd_read; -static cmd_resp_t cmd_resp; -static struct eth_device *lan_mac; -//static atomic_t seqcnt = ATOMIC_INIT(0); -static int seqcnt = 0; -static int cmd = 1; -//volatile uchar AthrHdrPkt[60]; -#endif - -#define ATHR_GLOBALREGBASE 0 - -//#define ATHR_PHY_MAX (sizeof(athrPhyInfo) / sizeof(athrPhyInfo[0])) -#define ATHR_PHY_MAX 5 - -/* Range of valid PHY IDs is [MIN..MAX] */ -#define ATHR_ID_MIN 0 -#define ATHR_ID_MAX (ATHR_PHY_MAX-1) - -/* Convenience macros to access myPhyInfo */ -#define ATHR_IS_ENET_PORT(phyUnit) (athrPhyInfo[phyUnit].isEnetPort) -#define ATHR_IS_PHY_ALIVE(phyUnit) (athrPhyInfo[phyUnit].isPhyAlive) -#define ATHR_ETHUNIT(phyUnit) (athrPhyInfo[phyUnit].ethUnit) -#define ATHR_PHYBASE(phyUnit) (athrPhyInfo[phyUnit].phyBase) -#define ATHR_PHYADDR(phyUnit) (athrPhyInfo[phyUnit].phyAddr) -#define ATHR_VLAN_TABLE_SETTING(phyUnit) (athrPhyInfo[phyUnit].VLANTableSetting) - - -#define ATHR_IS_ETHUNIT(phyUnit, ethUnit) \ - (ATHR_IS_ENET_PORT(phyUnit) && \ - ATHR_ETHUNIT(phyUnit) == (ethUnit)) - -#define ATHR_IS_WAN_PORT(phyUnit) (!(ATHR_ETHUNIT(phyUnit)==ENET_UNIT_LAN)) - -/* Forward references */ -BOOL athrs26_phy_is_link_alive(int phyUnit); -static uint32_t athrs26_reg_read(uint16_t reg_addr); -static void athrs26_reg_write(uint16_t reg_addr, - uint32_t reg_val); - -/****************************************************************************** -* -* athrs26_phy_is_link_alive - test to see if the specified link is alive -* -* RETURNS: -* TRUE --> link is alive -* FALSE --> link is down -*/ - -void athrs26_reg_init() -{ - - athrs26_reg_write(0x200, 0x200); - athrs26_reg_write(0x300, 0x200); - athrs26_reg_write(0x400, 0x200); - athrs26_reg_write(0x500, 0x200); - athrs26_reg_write(0x600, 0x7d); - -#ifdef S26_VER_1_0 - phy_reg_write(0, 0, 29, 41); - phy_reg_write(0, 0, 30, 0); - phy_reg_write(0, 1, 29, 41); - phy_reg_write(0, 1, 30, 0); - phy_reg_write(0, 2, 29, 41); - phy_reg_write(0, 2, 30, 0); - phy_reg_write(0, 3, 29, 41); - phy_reg_write(0, 3, 30, 0); - phy_reg_write(0, 4, 29, 41); - phy_reg_write(0, 4, 30, 0); -#endif - - athrs26_reg_write(0x38, 0xc000050e); - -#ifdef CFG_ATHRHDR_EN - athrs26_reg_write(0x104, 0x4804); -#else - athrs26_reg_write(0x104, 0x4004); -#endif - - athrs26_reg_write(0x60, 0xffffffff); - athrs26_reg_write(0x64, 0xaaaaaaaa); - athrs26_reg_write(0x68, 0x55555555); - athrs26_reg_write(0x6c, 0x0); - - athrs26_reg_write(0x70, 0x41af); -} - -BOOL -athrs26_phy_is_link_alive(int phyUnit) -{ - uint16_t phyHwStatus; - uint32_t phyBase; - uint32_t phyAddr; - - phyBase = ATHR_PHYBASE(phyUnit); - phyAddr = ATHR_PHYADDR(phyUnit); - - phy_reg_read(phyBase, phyAddr, ATHR_PHY_SPEC_STATUS, &phyHwStatus); - - if (phyHwStatus & ATHR_STATUS_LINK_PASS) - return TRUE; - - return FALSE; -} - - -/****************************************************************************** -* -* athrs26_phy_setup - reset and setup the PHY associated with -* the specified MAC unit number. -* -* Resets the associated PHY port. -* -* RETURNS: -* TRUE --> associated PHY is alive -* FALSE --> no LINKs on this ethernet unit -*/ - -BOOL -athrs26_phy_setup(int ethUnit) -{ - int phyUnit; - uint16_t phyHwStatus; - uint16_t timeout; - int liveLinks = 0; - uint32_t phyBase = 0; - BOOL foundPhy = FALSE; - uint32_t phyAddr = 0; - uint32_t regVal; - - - /* See if there's any configuration data for this enet */ - /* start auto negogiation on each phy */ - for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { - if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { - continue; - } - - - foundPhy = TRUE; - phyBase = ATHR_PHYBASE(phyUnit); - phyAddr = ATHR_PHYADDR(phyUnit); - - phy_reg_write(phyBase, phyAddr, ATHR_AUTONEG_ADVERT, - ATHR_ADVERTISE_ALL); - - /* Reset PHYs*/ - phy_reg_write(phyBase, phyAddr, ATHR_PHY_CONTROL, - ATHR_CTRL_AUTONEGOTIATION_ENABLE - | ATHR_CTRL_SOFTWARE_RESET); - - } - - if (!foundPhy) { - return FALSE; /* No PHY's configured for this ethUnit */ - } - - /* - * After the phy is reset, it takes a little while before - * it can respond properly. - */ - sysMsDelay(1000); - - /* - * Wait up to .75 seconds for ALL associated PHYs to finish - * autonegotiation. The only way we get out of here sooner is - * if ALL PHYs are connected AND finish autonegotiation. - */ - for (phyUnit=0; (phyUnit < ATHR_PHY_MAX) /*&& (timeout > 0) */; phyUnit++) { - if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { - continue; - } - - timeout=20; - for (;;) { - phyHwStatus = 0; - phy_reg_read(phyBase, phyAddr, ATHR_PHY_CONTROL, &phyHwStatus); - - if (ATHR_RESET_DONE(phyHwStatus)) { - DRV_PRINT(DRV_DEBUG_PHYSETUP, - ("Port %d, Neg Success\n", phyUnit)); - break; - } - if (timeout == 0) { - DRV_PRINT(DRV_DEBUG_PHYSETUP, - ("Port %d, Negogiation timeout\n", phyUnit)); - break; - } - if (--timeout == 0) { - DRV_PRINT(DRV_DEBUG_PHYSETUP, - ("Port %d, Negogiation timeout\n", phyUnit)); - break; - } - - sysMsDelay(150); - } - } - - /* - * All PHYs have had adequate time to autonegotiate. - * Now initialize software status. - * - * It's possible that some ports may take a bit longer - * to autonegotiate; but we can't wait forever. They'll - * get noticed by mv_phyCheckStatusChange during regular - * polling activities. - */ - for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { - if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { - continue; - } - - if (athrs26_phy_is_link_alive(phyUnit)) { - liveLinks++; - ATHR_IS_PHY_ALIVE(phyUnit) = TRUE; - } else { - ATHR_IS_PHY_ALIVE(phyUnit) = FALSE; - } - - phy_reg_read(ATHR_PHYBASE(phyUnit), ATHR_PHYADDR(phyUnit), - ATHR_PHY_SPEC_STATUS, ®Val); - DRV_PRINT(DRV_DEBUG_PHYSETUP, - ("eth%d: Phy Specific Status=%4.4x\n", ethUnit, regVal)); - } -#if 0 - /* if using header for register configuration, we have to */ - /* configure s26 register after frame transmission is enabled */ - - athrs26_reg_write(0x200, 0x200); - athrs26_reg_write(0x300, 0x200); - athrs26_reg_write(0x400, 0x200); - athrs26_reg_write(0x500, 0x200); - athrs26_reg_write(0x600, 0x200); - athrs26_reg_write(0x38, 0x50e); -#endif -#ifndef CFG_ATHRHDR_EN -/* if using header for register configuration, we have to */ - /* configure s26 register after frame transmission is enabled */ - athrs26_reg_init(); -#endif - - return (liveLinks > 0); -} - -/****************************************************************************** -* -* athrs26_phy_is_fdx - Determines whether the phy ports associated with the -* specified device are FULL or HALF duplex. -* -* RETURNS: -* 1 --> FULL -* 0 --> HALF -*/ -int -athrs26_phy_is_fdx(int ethUnit) -{ - int phyUnit; - uint32_t phyBase; - uint32_t phyAddr; - uint16_t phyHwStatus; - int ii = 200; - - if (ethUnit == ENET_UNIT_LAN) - return TRUE; - - for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { - if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { - continue; - } - - if (athrs26_phy_is_link_alive(phyUnit)) { - - phyBase = ATHR_PHYBASE(phyUnit); - phyAddr = ATHR_PHYADDR(phyUnit); - - do { - phy_reg_read(phyBase, phyAddr, ATHR_PHY_SPEC_STATUS, &phyHwStatus); - sysMsDelay(10); - } while((!(phyHwStatus & ATHR_STATUS_RESOVLED)) && --ii); - - if (phyHwStatus & ATHER_STATUS_FULL_DEPLEX) - return TRUE; - } - } - - return FALSE; -} - - -/****************************************************************************** -* -* athrs26_phy_speed - Determines the speed of phy ports associated with the -* specified device. -* -* RETURNS: -* AG7100_PHY_SPEED_10T, AG7100_PHY_SPEED_100TX; -* AG7100_PHY_SPEED_1000T; -*/ - -BOOL -athrs26_phy_speed(int ethUnit) -{ - int phyUnit; - uint16_t phyHwStatus; - uint32_t phyBase; - uint32_t phyAddr; - int ii = 200; - - if (ethUnit == ENET_UNIT_LAN) - return _100BASET; - - for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { - if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { - continue; - } - - if (athrs26_phy_is_link_alive(phyUnit)) { - - phyBase = ATHR_PHYBASE(phyUnit); - phyAddr = ATHR_PHYADDR(phyUnit); - - do { - phy_reg_read(phyBase, phyAddr, - ATHR_PHY_SPEC_STATUS, &phyHwStatus); - sysMsDelay(10); - }while((!(phyHwStatus & ATHR_STATUS_RESOVLED)) && --ii); - - phyHwStatus = ((phyHwStatus & ATHER_STATUS_LINK_MASK) >> - ATHER_STATUS_LINK_SHIFT); - - switch(phyHwStatus) { - case 0: - return _10BASET; - case 1: - return _100BASET; - case 2: - return _1000BASET; - default: - DRV_PRINT(DRV_DEBUG_PHYERROR, ("Unkown speed read!\n")); - } - } - } - - return _10BASET; -} - -/***************************************************************************** -* -* athr_phy_is_up -- checks for significant changes in PHY state. -* -* A "significant change" is: -* dropped link (e.g. ethernet cable unplugged) OR -* autonegotiation completed + link (e.g. ethernet cable plugged in) -* -* When a PHY is plugged in, phyLinkGained is called. -* When a PHY is unplugged, phyLinkLost is called. -*/ - -int -athrs26_phy_is_up(int ethUnit) -{ - int phyUnit; - uint16_t phyHwStatus; - athrPhyInfo_t *lastStatus; - int linkCount = 0; - int lostLinks = 0; - int gainedLinks = 0; - uint32_t phyBase; - uint32_t phyAddr; -#ifdef CFG_ATHRHDR_REG - /* if using header to config s26, the link of MAC0 should always be up */ - if (ethUnit == ENET_UNIT_LAN) - return 1; -#endif - - for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { - if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { - continue; - } - - phyBase = ATHR_PHYBASE(phyUnit); - phyAddr = ATHR_PHYADDR(phyUnit); - - - lastStatus = &athrPhyInfo[phyUnit]; - phy_reg_read(phyBase, phyAddr, ATHR_PHY_SPEC_STATUS, &phyHwStatus); - - if (lastStatus->isPhyAlive) { /* last known link status was ALIVE */ - /* See if we've lost link */ - if (phyHwStatus & ATHR_STATUS_LINK_PASS) { - linkCount++; - } else { - lostLinks++; - DRV_PRINT(DRV_DEBUG_PHYCHANGE,("\nenet%d port%d down\n", - ethUnit, phyUnit)); - lastStatus->isPhyAlive = FALSE; - } - } else { /* last known link status was DEAD */ - /* Check for reset complete */ - phy_reg_read(phyBase, phyAddr, ATHR_PHY_STATUS, &phyHwStatus); - if (!ATHR_RESET_DONE(phyHwStatus)) - continue; - - /* Check for AutoNegotiation complete */ - if (ATHR_AUTONEG_DONE(phyHwStatus)) { - //printk("autoneg done\n"); - gainedLinks++; - linkCount++; - DRV_PRINT(DRV_DEBUG_PHYCHANGE,("\nenet%d port%d up\n", - ethUnit, phyUnit)); - lastStatus->isPhyAlive = TRUE; - } - } - } - - return (linkCount); - -#if 0 - if (linkCount == 0) { - if (lostLinks) { - /* We just lost the last link for this MAC */ - phyLinkLost(ethUnit); - } - } else { - if (gainedLinks == linkCount) { - /* We just gained our first link(s) for this MAC */ - phyLinkGained(ethUnit); - } - } -#endif -} - -#ifdef CFG_ATHRHDR_EN -void athr_hdr_timeout(void){ - eth_halt(); - NetState = NETLOOP_FAIL; -} - -void athr_hdr_handler(uchar *recv_pkt, unsigned dest, unsigned src, unsigned len){ - header_receive_pkt(recv_pkt); - NetState = NETLOOP_SUCCESS; -} -static int -athrs26_header_config_reg (struct eth_device *dev, uint8_t wr_flag, - uint16_t reg_addr, uint16_t cmd_len, - uint8_t *val) -{ - at_header_t at_header; - reg_cmd_t reg_cmd; - uchar *AthrHdrPkt; - - AthrHdrPkt = NetTxPacket; - - if(AthrHdrPkt == NULL) { - printf("Null packet\n"); - return; - } - memset(AthrHdrPkt,0,60); - - /*fill at_header*/ - at_header.reserved0 = 0x10; //default - at_header.priority = 0; - at_header.type = 0x5; - at_header.broadcast = 0; - at_header.from_cpu = 1; - at_header.reserved1 = 0x01; //default - at_header.port_num = 0; - - AthrHdrPkt[0] = at_header.port_num; - AthrHdrPkt[0] |= at_header.reserved1 << 4; - AthrHdrPkt[0] |= at_header.from_cpu << 6; - AthrHdrPkt[0] |= at_header.broadcast << 7; - - AthrHdrPkt[1] = at_header.type; - AthrHdrPkt[1] |= at_header.priority << 4; - AthrHdrPkt[1] |= at_header.reserved0 << 6; - - - /*fill reg cmd*/ - if(cmd_len > 4) - cmd_len = 4;//only support 32bits register r/w - - reg_cmd.reg_addr = reg_addr&0x3FFFC; - reg_cmd.cmd_len = cmd_len; - reg_cmd.cmd = wr_flag; - reg_cmd.reserved2 = 0x5; //default - reg_cmd.seq_num = seqcnt; - - AthrHdrPkt[2] = reg_cmd.reg_addr & 0xff; - AthrHdrPkt[3] = (reg_cmd.reg_addr & 0xff00) >> 8; - AthrHdrPkt[4] = (reg_cmd.reg_addr & 0x30000) >> 16; - AthrHdrPkt[4] |= reg_cmd.cmd_len << 4; - AthrHdrPkt[5] = reg_cmd.cmd << 4; - AthrHdrPkt[5] |= reg_cmd.reserved2 << 5; - AthrHdrPkt[6] = (reg_cmd.seq_num & 0x7f) << 1; - AthrHdrPkt[7] = (reg_cmd.seq_num & 0x7f80) >> 7; - AthrHdrPkt[8] = (reg_cmd.seq_num & 0x7f8000) >> 15; - AthrHdrPkt[9] = (reg_cmd.seq_num & 0x7f800000) >> 23; - - /*fill reg data*/ - if(!wr_flag)//write - memcpy((AthrHdrPkt + 10), val, cmd_len); - - /*start xmit*/ - if(dev == NULL) { - printf("ERROR device not found\n"); - return -1; - } - header_xmit(dev, AthrHdrPkt ,60); - return 0; -} -void athr_hdr_func(void) { - - NetSetTimeout (1 * CFG_HZ,athr_hdr_timeout ); - NetSetHandler (athr_hdr_handler); - - if(cmd) - athrs26_header_config_reg(lan_mac, cmd, cmd_read.reg_addr, cmd_read.cmd_len, cmd_read.reg_data); - else - athrs26_header_config_reg(lan_mac, cmd, cmd_write.reg_addr, cmd_write.cmd_len, cmd_write.reg_data); -} -static int -athrs26_header_write_reg(uint16_t reg_addr, uint16_t cmd_len, uint8_t *reg_data) -{ - int i = 2; - cmd_write.reg_addr = reg_addr; - cmd_write.cmd_len = cmd_len; - cmd_write.reg_data = reg_data; - cmd = 0; - seqcnt++; - - do { - if (NetLoop(ATHRHDR) >= 0) /* polls for read/write ack from PHY */ - break; - } while (i--); - - return i; -} - -static int -athrs26_header_read_reg(uint16_t reg_addr, uint16_t cmd_len, uint8_t *reg_data) -{ - int i = 2; - - cmd_read.reg_addr = reg_addr; - cmd_read.cmd_len = cmd_len; - cmd_read.reg_data = reg_data; - cmd = 1; - seqcnt++; - - do { - if (NetLoop(ATHRHDR) >= 0) /* polls for read/write ack from PHY */ - break; - } while (i--); - - if ((i==0) || (seqcnt != cmd_resp.seq) || (cmd_len != cmd_resp.len)) { - return -1; - } - memcpy (cmd_read.reg_data, cmd_resp.data, cmd_len); - return 0; -} -int header_receive_pkt(uchar *recv_pkt) -{ - cmd_resp.len = recv_pkt[4] >> 4; - if (cmd_resp.len > 10) - goto out; - - cmd_resp.seq = recv_pkt[6] >> 1; - cmd_resp.seq |= recv_pkt[7] << 7; - cmd_resp.seq |= recv_pkt[8] << 15; - cmd_resp.seq |= recv_pkt[9] << 23; - - if (cmd_resp.seq < seqcnt) - goto out; - memcpy (cmd_resp.data, (recv_pkt + 10), cmd_resp.len); -out: - return 0; -} - -void athrs26_reg_dev(struct eth_device *mac) -{ - lan_mac = mac; -} - -#endif - -static uint32_t -athrs26_reg_read(uint16_t reg_addr) -{ -#ifndef CFG_ATHRHDR_REG - uint16_t reg_word_addr = reg_addr / 2, phy_val; - uint32_t phy_addr; - uint8_t phy_reg; - - /* configure register high address */ - phy_addr = 0x18; - phy_reg = 0x0; - phy_val = (reg_word_addr >> 8) & 0x1ff; /* bit16-8 of reg address*/ - phy_reg_write (0, phy_addr, phy_reg, phy_val); - - /* read register with low address */ - phy_addr = 0x10 | ((reg_word_addr >> 5) & 0x7); /* bit7-5 of reg address */ - phy_reg = reg_word_addr & 0x1f; /* bit 4-0 of reg address*/ - phy_reg_read(0, phy_addr, phy_reg, &phy_val); - - return phy_val; -#else - uint8_t reg_data[4]; - - memset (reg_data, 0, 4); - athrs26_header_read_reg(reg_addr, 4, reg_data); - return (reg_data[0] | (reg_data[1] << 8) | (reg_data[2] << 16) | (reg_data[3] << 24)); -#endif -} - -static void -athrs26_reg_write(uint16_t reg_addr, uint32_t reg_val) -{ -#ifndef CFG_ATHRHDR_REG - uint16_t reg_word_addr = reg_addr / 2, phy_val; - uint32_t phy_addr; - uint8_t phy_reg; - - /* configure register high address */ - phy_addr = 0x18; - phy_reg = 0x0; - phy_val = (reg_word_addr >> 8) & 0x1ff; /* bit16-8 of reg address*/ - phy_reg_write (0, phy_addr, phy_reg, phy_val); - - /* read register with low address */ - phy_addr = 0x10 | ((reg_word_addr >> 5) & 0x7); /* bit7-5 of reg address */ - phy_reg = reg_word_addr & 0x1f; /* bit 4-0 of reg address */ - phy_reg_write (0, phy_addr, phy_reg, reg_val); -#else - uint8_t reg_data[4]; - - memset (reg_data, 0, 4); - reg_data[0] = (uint8_t)(0x00ff & reg_val); - reg_data[1] = (uint8_t)((0xff00 & reg_val) >> 8); - reg_data[2] = (uint8_t)((0xff0000 & reg_val) >> 16); - reg_data[3] = (uint8_t)((0xff000000 & reg_val) >> 24); - - athrs26_header_write_reg (reg_addr, 4, reg_data); -#endif - -} - diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/athrs26_phy.h b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/athrs26_phy.h deleted file mode 100644 index 0fdde376eb..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/athrs26_phy.h +++ /dev/null @@ -1,134 +0,0 @@ -#ifndef _ATHRS26_PHY_H -#define _ATHRS26_PHY_H - -/*****************/ -/* PHY Registers */ -/*****************/ -#define ATHR_PHY_CONTROL 0 -#define ATHR_PHY_STATUS 1 -#define ATHR_PHY_ID1 2 -#define ATHR_PHY_ID2 3 -#define ATHR_AUTONEG_ADVERT 4 -#define ATHR_LINK_PARTNER_ABILITY 5 -#define ATHR_AUTONEG_EXPANSION 6 -#define ATHR_NEXT_PAGE_TRANSMIT 7 -#define ATHR_LINK_PARTNER_NEXT_PAGE 8 -#define ATHR_1000BASET_CONTROL 9 -#define ATHR_1000BASET_STATUS 10 -#define ATHR_PHY_SPEC_CONTROL 16 -#define ATHR_PHY_SPEC_STATUS 17 -#define ATHR_DEBUG_PORT_ADDRESS 29 -#define ATHR_DEBUG_PORT_DATA 30 - -/* ATHR_PHY_CONTROL fields */ -#define ATHR_CTRL_SOFTWARE_RESET 0x8000 -#define ATHR_CTRL_SPEED_LSB 0x2000 -#define ATHR_CTRL_AUTONEGOTIATION_ENABLE 0x1000 -#define ATHR_CTRL_RESTART_AUTONEGOTIATION 0x0200 -#define ATHR_CTRL_SPEED_FULL_DUPLEX 0x0100 -#define ATHR_CTRL_SPEED_MSB 0x0040 - -#define ATHR_RESET_DONE(phy_control) \ - (((phy_control) & (ATHR_CTRL_SOFTWARE_RESET)) == 0) - -/* Phy status fields */ -#define ATHR_STATUS_AUTO_NEG_DONE 0x0020 - -#define ATHR_AUTONEG_DONE(ip_phy_status) \ - (((ip_phy_status) & \ - (ATHR_STATUS_AUTO_NEG_DONE)) == \ - (ATHR_STATUS_AUTO_NEG_DONE)) - -/* Link Partner ability */ -#define ATHR_LINK_100BASETX_FULL_DUPLEX 0x0100 -#define ATHR_LINK_100BASETX 0x0080 -#define ATHR_LINK_10BASETX_FULL_DUPLEX 0x0040 -#define ATHR_LINK_10BASETX 0x0020 - -/* Advertisement register. */ -#define ATHR_ADVERTISE_NEXT_PAGE 0x8000 -#define ATHR_ADVERTISE_ASYM_PAUSE 0x0800 -#define ATHR_ADVERTISE_PAUSE 0x0400 -#define ATHR_ADVERTISE_100FULL 0x0100 -#define ATHR_ADVERTISE_100HALF 0x0080 -#define ATHR_ADVERTISE_10FULL 0x0040 -#define ATHR_ADVERTISE_10HALF 0x0020 - -#define ATHR_ADVERTISE_ALL (ATHR_ADVERTISE_10HALF | ATHR_ADVERTISE_10FULL | \ - ATHR_ADVERTISE_100HALF | ATHR_ADVERTISE_100FULL) - -/* 1000BASET_CONTROL */ -#define ATHR_ADVERTISE_1000FULL 0x0200 - -/* Phy Specific status fields */ -#define ATHER_STATUS_LINK_MASK 0xC000 -#define ATHER_STATUS_LINK_SHIFT 14 -#define ATHER_STATUS_FULL_DEPLEX 0x2000 -#define ATHR_STATUS_LINK_PASS 0x0400 -#define ATHR_STATUS_RESOVLED 0x0800 - -/*phy debug port register */ -#define ATHER_DEBUG_SERDES_REG 5 - -/* Serdes debug fields */ -#define ATHER_SERDES_BEACON 0x0100 - -#ifndef BOOL -#define BOOL int -#define TRUE 1 -#define FALSE 0 -#endif - -#define sysMsDelay(_x) udelay((_x) * 1000) - -#undef S26_VER_1_0 - -#ifdef CFG_ATHRHDR_EN - -#include -#define header_xmit(dev,pkt,len) dev->send(dev,pkt,len) //dev_queue_xmit(skb) -#define header_recv_ack(dev) dev->recv(dev) //dev_queue_xmit(skb) - -typedef enum { - NORMAL_PACKET, - RESERVED0, - MIB_1ST, - RESERVED1, - RESERVED2, - READ_WRITE_REG, - READ_WRITE_REG_ACK, - RESERVED3 -} ATHR_HDR_TYPE; - -typedef struct { - uint16_t reserved0; - uint16_t priority; - uint16_t type ; - uint16_t broadcast; - uint16_t from_cpu; - uint16_t reserved1; - uint16_t port_num; -}at_header_t; - -typedef struct { - uint64_t reg_addr; - uint64_t reserved0; - uint64_t cmd_len; - uint64_t reserved1; - uint64_t cmd; - uint64_t reserved2; - uint64_t seq_num; -}reg_cmd_t; -void athrs26_reg_init(void); -int header_receive_pkt(uchar *pkt); -void athrs26_reg_dev(struct eth_device *mac); - -#endif - -int athrs26_phy_is_up(int unit); -int athrs26_phy_is_fdx(int unit); -int athrs26_phy_speed(int unit); -BOOL athrs26_phy_setup(int unit); - -#endif /* _ATHRS26_PHY_H */ - diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/config.mk b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/config.mk deleted file mode 100644 index c0e5d82445..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/config.mk +++ /dev/null @@ -1,60 +0,0 @@ -# -# (C) Copyright 2003 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -# -# Danube board with MIPS 24Kc CPU core -# -sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp - -ifdef CONFIG_LZMA_BOOTSTRAP - -ifdef BUILD_BOOTSTRAP - -$(info BUILD_BOOTSTRAP ) -#TEXT_BASE = 0xB0000000 -TEXT_BASE = 0x80010000 - -else # BUILD_BOOTSTRAP - -ifndef TEXT_BASE -$(info redefine TEXT_BASE = 0x80040000 ) -TEXT_BASE = 0x80040000 -endif - -endif # BUILD_BOOTSTRAP - -else - -ifdef BUILD_BOOTSTRAP -$(error BUILD_BOOTSTRAP but not enabled in config) -endif - -ifndef TEXT_BASE -## Standard: boot from ebu -$(info redefine TEXT_BASE = 0xB0000000 ) -TEXT_BASE = 0xB0000000 -## For testing: boot from RAM -# TEXT_BASE = 0x80100000 -endif - -endif # CONFIG_LZMA_BOOTSTRAP diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/ddr_settings.h b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/ddr_settings.h deleted file mode 100644 index 4df6f1170c..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/ddr_settings.h +++ /dev/null @@ -1,50 +0,0 @@ -/* Settings for Denali DDR SDRAM controller */ -/* Optimise for DDR PSC A3S12D40ETP for arv4518pw Danube Board DDR 166 Mhz - by Ngp 14th Sept. 2010 */ - -#define MC_DC0_VALUE 0x1B1B -#define MC_DC1_VALUE 0x0 -#define MC_DC2_VALUE 0x0 -#define MC_DC3_VALUE 0x0 -#define MC_DC4_VALUE 0x0 -#define MC_DC5_VALUE 0x200 -#define MC_DC6_VALUE 0x605 -#define MC_DC7_VALUE 0x303 -#define MC_DC8_VALUE 0x102 -#define MC_DC9_VALUE 0x70a -#define MC_DC10_VALUE 0x203 -#define MC_DC11_VALUE 0xc02 -#define MC_DC12_VALUE 0x1C8 -#define MC_DC13_VALUE 0x1 -#define MC_DC14_VALUE 0x0 -#define MC_DC15_VALUE 0x130 /* WDQS tuning for clk_wr*/ -#define MC_DC16_VALUE 0xC800 -#define MC_DC17_VALUE 0xd -#define MC_DC18_VALUE 0x301 -#define MC_DC19_VALUE 0x200 -#define MC_DC20_VALUE 0xA03 /* A04 for reference board, A03 for Eval board */ -#define MC_DC21_VALUE 0x1b00 -#define MC_DC22_VALUE 0x1b1b -#define MC_DC23_VALUE 0x0 -#define MC_DC24_VALUE 0x59 /* WDQS Tuning for DQS */ -#define MC_DC25_VALUE 0x0 -#define MC_DC26_VALUE 0x0 -#define MC_DC27_VALUE 0x0 -#define MC_DC28_VALUE 0x510 -#define MC_DC29_VALUE 0x4e20 -#define MC_DC30_VALUE 0x8235 -#define MC_DC31_VALUE 0x0 -#define MC_DC32_VALUE 0x0 -#define MC_DC33_VALUE 0x0 -#define MC_DC34_VALUE 0x0 -#define MC_DC35_VALUE 0x0 -#define MC_DC36_VALUE 0x0 -#define MC_DC37_VALUE 0x0 -#define MC_DC38_VALUE 0x0 -#define MC_DC39_VALUE 0x0 -#define MC_DC40_VALUE 0x0 -#define MC_DC41_VALUE 0x0 -#define MC_DC42_VALUE 0x0 -#define MC_DC43_VALUE 0x0 -#define MC_DC44_VALUE 0x0 -#define MC_DC45_VALUE 0x500 -#define MC_DC46_VALUE 0x0 diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/ddr_settings_psc_166.h b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/ddr_settings_psc_166.h deleted file mode 100644 index 445b7dac1f..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/ddr_settings_psc_166.h +++ /dev/null @@ -1,51 +0,0 @@ -/* Settings for Denali DDR SDRAM controller */ -/* Optimise for PSC DDR A2S56D40CTP for Danube Ref Board DDR 166 Mhz - by Ng Aik Ann 27th Nov 2006 */ - -#define MC_DC0_VALUE 0x1B1B -#define MC_DC1_VALUE 0x0 -#define MC_DC2_VALUE 0x0 -#define MC_DC3_VALUE 0x0 -#define MC_DC4_VALUE 0x0 -#define MC_DC5_VALUE 0x200 -#define MC_DC6_VALUE 0x605 -#define MC_DC7_VALUE 0x303 -#define MC_DC8_VALUE 0x102 -#define MC_DC9_VALUE 0x70a -#define MC_DC10_VALUE 0x203 -#define MC_DC11_VALUE 0xc02 -#define MC_DC12_VALUE 0x1C8 -#define MC_DC13_VALUE 0x1 -#define MC_DC14_VALUE 0x0 -#define MC_DC15_VALUE 0x120 /* WDQS tuning for clk_wr*/ -#define MC_DC16_VALUE 0xC800 -#define MC_DC17_VALUE 0xd -#define MC_DC18_VALUE 0x301 -#define MC_DC19_VALUE 0x200 -#define MC_DC20_VALUE 0xA04 /* A04 for reference board, A03 for Eval board */ -#define MC_DC21_VALUE 0x1700 -#define MC_DC22_VALUE 0x1717 -#define MC_DC23_VALUE 0x0 -#define MC_DC24_VALUE 0x52 /* WDQS Tuning for DQS */ -#define MC_DC25_VALUE 0x0 -#define MC_DC26_VALUE 0x0 -#define MC_DC27_VALUE 0x0 -#define MC_DC28_VALUE 0x510 -#define MC_DC29_VALUE 0x4e20 -#define MC_DC30_VALUE 0x8235 -#define MC_DC31_VALUE 0x0 -#define MC_DC32_VALUE 0x0 -#define MC_DC33_VALUE 0x0 -#define MC_DC34_VALUE 0x0 -#define MC_DC35_VALUE 0x0 -#define MC_DC36_VALUE 0x0 -#define MC_DC37_VALUE 0x0 -#define MC_DC38_VALUE 0x0 -#define MC_DC39_VALUE 0x0 -#define MC_DC40_VALUE 0x0 -#define MC_DC41_VALUE 0x0 -#define MC_DC42_VALUE 0x0 -#define MC_DC43_VALUE 0x0 -#define MC_DC44_VALUE 0x0 -#define MC_DC45_VALUE 0x500 -//#define MC_DC45_VALUE 0x400 -#define MC_DC46_VALUE 0x0 diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/lowlevel_init.S b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/lowlevel_init.S deleted file mode 100644 index 2f2c2255e0..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/lowlevel_init.S +++ /dev/null @@ -1,622 +0,0 @@ -/* - * Memory sub-system initialization code for Danube board. - * Andre Messerschmidt - * Copyright (c) 2005 Infineon Technologies AG - * - * Based on Inca-IP code - * Copyright (c) 2003 Wolfgang Denk - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -/* History: - peng liu May 25, 2006, for PLL setting after reset, 05252006 - */ -#include -#include -#include - -#if 0 - -#if defined(CONFIG_USE_DDR_RAM) - -#if defined(CONFIG_USE_DDR_RAM_CFG_111M) -#include "ddr_settings_r111.h" -#define DDR111 -#elif defined(CONFIG_USE_DDR_RAM_CFG_166M) -#include "ddr_settings_r166.h" -#define DDR166 -#elif defined(CONFIG_USE_DDR_RAM_CFG_e111M) -#include "ddr_settings_e111.h" -#define DDR111 -#elif defined(CONFIG_USE_DDR_RAM_CFG_e166M) -#include "ddr_settings_e166.h" -#define DDR166 -#elif defined(CONFIG_USE_DDR_RAM_CFG_promos400) -#include "ddr_settings_PROMOSDDR400.h" -#define DDR166 -#elif defined(CONFIG_USE_DDR_RAM_CFG_samsung166) -#include "ddr_settings_Samsung_166.h" -#define DDR166 -#elif defined(CONFIG_USE_DDR_RAM_CFG_psc166) -#include "ddr_settings_psc_166.h" -#define DDR166 -#else -#warning "missing definition for ddr_settings.h, use default!" -#include "ddr_settings.h" -#endif -#endif /* CONFIG_USE_DDR_RAM */ - -#else - -#include "ddr_settings_psc_166.h" -#define DDR166 - -#endif - -#if defined(CONFIG_USE_DDR_RAM) && !defined(MC_DC0_VALUE) -#error "missing include of ddr_settings.h" -#endif - -#define EBU_MODUL_BASE 0xBE105300 -#define EBU_CLC(value) 0x0000(value) -#define EBU_CON(value) 0x0010(value) -#define EBU_ADDSEL0(value) 0x0020(value) -#define EBU_ADDSEL1(value) 0x0024(value) -#define EBU_ADDSEL2(value) 0x0028(value) -#define EBU_ADDSEL3(value) 0x002C(value) -#define EBU_BUSCON0(value) 0x0060(value) -#define EBU_BUSCON1(value) 0x0064(value) -#define EBU_BUSCON2(value) 0x0068(value) -#define EBU_BUSCON3(value) 0x006C(value) - -#define MC_MODUL_BASE 0xBF800000 -#define MC_ERRCAUSE(value) 0x0010(value) -#define MC_ERRADDR(value) 0x0020(value) -#define MC_CON(value) 0x0060(value) - -#define MC_SRAM_ENABLE 0x00000004 -#define MC_SDRAM_ENABLE 0x00000002 -#define MC_DDRRAM_ENABLE 0x00000001 - -#define MC_SDR_MODUL_BASE 0xBF800200 -#define MC_IOGP(value) 0x0000(value) -#define MC_CTRLENA(value) 0x0010(value) -#define MC_MRSCODE(value) 0x0020(value) -#define MC_CFGDW(value) 0x0030(value) -#define MC_CFGPB0(value) 0x0040(value) -#define MC_LATENCY(value) 0x0080(value) -#define MC_TREFRESH(value) 0x0090(value) -#define MC_SELFRFSH(value) 0x00A0(value) - -#define MC_DDR_MODUL_BASE 0xBF801000 -#define MC_DC00(value) 0x0000(value) -#define MC_DC01(value) 0x0010(value) -#define MC_DC02(value) 0x0020(value) -#define MC_DC03(value) 0x0030(value) -#define MC_DC04(value) 0x0040(value) -#define MC_DC05(value) 0x0050(value) -#define MC_DC06(value) 0x0060(value) -#define MC_DC07(value) 0x0070(value) -#define MC_DC08(value) 0x0080(value) -#define MC_DC09(value) 0x0090(value) -#define MC_DC10(value) 0x00A0(value) -#define MC_DC11(value) 0x00B0(value) -#define MC_DC12(value) 0x00C0(value) -#define MC_DC13(value) 0x00D0(value) -#define MC_DC14(value) 0x00E0(value) -#define MC_DC15(value) 0x00F0(value) -#define MC_DC16(value) 0x0100(value) -#define MC_DC17(value) 0x0110(value) -#define MC_DC18(value) 0x0120(value) -#define MC_DC19(value) 0x0130(value) -#define MC_DC20(value) 0x0140(value) -#define MC_DC21(value) 0x0150(value) -#define MC_DC22(value) 0x0160(value) -#define MC_DC23(value) 0x0170(value) -#define MC_DC24(value) 0x0180(value) -#define MC_DC25(value) 0x0190(value) -#define MC_DC26(value) 0x01A0(value) -#define MC_DC27(value) 0x01B0(value) -#define MC_DC28(value) 0x01C0(value) -#define MC_DC29(value) 0x01D0(value) -#define MC_DC30(value) 0x01E0(value) -#define MC_DC31(value) 0x01F0(value) -#define MC_DC32(value) 0x0200(value) -#define MC_DC33(value) 0x0210(value) -#define MC_DC34(value) 0x0220(value) -#define MC_DC35(value) 0x0230(value) -#define MC_DC36(value) 0x0240(value) -#define MC_DC37(value) 0x0250(value) -#define MC_DC38(value) 0x0260(value) -#define MC_DC39(value) 0x0270(value) -#define MC_DC40(value) 0x0280(value) -#define MC_DC41(value) 0x0290(value) -#define MC_DC42(value) 0x02A0(value) -#define MC_DC43(value) 0x02B0(value) -#define MC_DC44(value) 0x02C0(value) -#define MC_DC45(value) 0x02D0(value) -#define MC_DC46(value) 0x02E0(value) - -#define RCU_OFFSET 0xBF203000 -#define RCU_RST_REQ (RCU_OFFSET + 0x0010) -#define RCU_STS (RCU_OFFSET + 0x0014) - -#define CGU_OFFSET 0xBF103000 -#define PLL0_CFG (CGU_OFFSET + 0x0004) -#define PLL1_CFG (CGU_OFFSET + 0x0008) -#define PLL2_CFG (CGU_OFFSET + 0x000C) -#define CGU_SYS (CGU_OFFSET + 0x0010) -#define CGU_UPDATE (CGU_OFFSET + 0x0014) -#define IF_CLK (CGU_OFFSET + 0x0018) -#define CGU_SMD (CGU_OFFSET + 0x0020) -#define CGU_CT1SR (CGU_OFFSET + 0x0028) -#define CGU_CT2SR (CGU_OFFSET + 0x002C) -#define CGU_PCMCR (CGU_OFFSET + 0x0030) -#define PCI_CR_PCI (CGU_OFFSET + 0x0034) -#define CGU_OSC_CTRL (CGU_OFFSET + 0x001C) -#define CGU_MIPS_PWR_DWN (CGU_OFFSET + 0x0038) -#define CLK_MEASURE (CGU_OFFSET + 0x003C) - -//05252006 -#define pll0_35MHz_CONFIG 0x9D861059 -#define pll1_35MHz_CONFIG 0x1A260CD9 -#define pll2_35MHz_CONFIG 0x8000f1e5 -#define pll0_36MHz_CONFIG 0x1000125D -#define pll1_36MHz_CONFIG 0x1B1E0C99 -#define pll2_36MHz_CONFIG 0x8002f2a1 -//05252006 - -//06063001-joelin disable the PCI CFRAME mask -start -/*CFRAME is an I/O signal, in the chip, the output CFRAME is selected via GPIO altsel pins, so if you select MII1 RXD1, the CFRAME will not come out. -But the CFRAME input still take the signal from the pad and not disabled when altsel choose other function. So when MII1_RXD1 is low from other device, the EBU interface will be disabled. - -The chip function in such a way that disable the CFRAME mask mean EBU not longer check CFRAME to be the device using the bus. -The side effect is the entire PCI block will see CFRAME low all the time meaning PCI cannot use the bus at all so no more PCI function. -*/ -#define PCI_CR_PR_OFFSET 0xBE105400 -#define PCI_CR_PCI_MOD_REG (PCI_CR_PR_OFFSET + 0x0030) -#define PCI_CONFIG_SPACE 0xB7000000 -#define CS_CFM (PCI_CONFIG_SPACE + 0x6C) -//06063001-joelin disable the PCI CFRAME mask -end - .set noreorder - - -/* - * void ebu_init(void) - */ - .globl ebu_init - .ent ebu_init -ebu_init: - -#if defined(CONFIG_EBU_ADDSEL0) || defined(CONFIG_EBU_ADDSEL1) || \ - defined(CONFIG_EBU_ADDSEL2) || defined(CONFIG_EBU_ADDSEL3) || \ - defined(CONFIG_EBU_BUSCON0) || defined(CONFIG_EBU_BUSCON1) || \ - defined(CONFIG_EBU_BUSCON2) || defined(CONFIG_EBU_BUSCON3) - - li t1, EBU_MODUL_BASE -#if defined(CONFIG_EBU_ADDSEL0) - li t2, CONFIG_EBU_ADDSEL0 - sw t2, EBU_ADDSEL0(t1) -#endif -#if defined(CONFIG_EBU_ADDSEL1) - li t2, CONFIG_EBU_ADDSEL1 - sw t2, EBU_ADDSEL1(t1) -#endif -#if defined(CONFIG_EBU_ADDSEL2) - li t2, CONFIG_EBU_ADDSEL2 - sw t2, EBU_ADDSEL2(t1) -#endif -#if defined(CONFIG_EBU_ADDSEL3) - li t2, CONFIG_EBU_ADDSEL3 - sw t2, EBU_ADDSEL3(t1) -#endif - -#if defined(CONFIG_EBU_BUSCON0) - li t2, CONFIG_EBU_BUSCON0 - sw t2, EBU_BUSCON0(t1) -#endif -#if defined(CONFIG_EBU_BUSCON1) - li t2, CONFIG_EBU_BUSCON1 - sw t2, EBU_BUSCON1(t1) -#endif -#if defined(CONFIG_EBU_BUSCON2) - li t2, CONFIG_EBU_BUSCON2 - sw t2, EBU_BUSCON2(t1) -#endif -#if defined(CONFIG_EBU_BUSCON3) - li t2, CONFIG_EBU_BUSCON3 - sw t2, EBU_BUSCON3(t1) -#endif - -#endif - - j ra - nop - - .end ebu_init - - -/* - * void cgu_init(long) - * - * a0 has the clock value - */ - .globl cgu_init - .ent cgu_init -cgu_init: - li t2, CGU_SYS - lw t2,0(t2) - beq t2,a0,freq_up2date - nop - - li t2, RCU_STS - lw t2, 0(t2) - and t2,0x00020000 - beq t2,0x00020000,boot_36MHZ - nop -//05252006 - li t1, PLL0_CFG - li t2, pll0_35MHz_CONFIG - sw t2,0(t1) - li t1, PLL1_CFG - li t2, pll1_35MHz_CONFIG - sw t2,0(t1) - li t1, PLL2_CFG - li t2, pll2_35MHz_CONFIG - sw t2,0(t1) - li t1, CGU_SYS - sw a0,0(t1) - li t1, RCU_RST_REQ - li t2, 0x40000008 - sw t2,0(t1) - b wait_reset - nop -boot_36MHZ: - li t1, PLL0_CFG - li t2, pll0_36MHz_CONFIG - sw t2,0(t1) - li t1, PLL1_CFG - li t2, pll1_36MHz_CONFIG - sw t2,0(t1) - li t1, PLL2_CFG - li t2, pll2_36MHz_CONFIG - sw t2,0(t1) - li t1, CGU_SYS - sw a0,0(t1) - li t1, RCU_RST_REQ - li t2, 0x40000008 - sw t2,0(t1) -//05252006 - -wait_reset: - b wait_reset - nop -freq_up2date: - j ra - nop - - .end cgu_init - -#ifndef CONFIG_USE_DDR_RAM -/* - * void sdram_init(long) - * - * a0 has the clock value - */ - .globl sdram_init - .ent sdram_init -sdram_init: - - /* SDRAM Initialization - */ - li t1, MC_MODUL_BASE - - /* Clear Error log registers */ - sw zero, MC_ERRCAUSE(t1) - sw zero, MC_ERRADDR(t1) - - /* Enable SDRAM module in memory controller */ - li t3, MC_SDRAM_ENABLE - lw t2, MC_CON(t1) - or t3, t2, t3 - sw t3, MC_CON(t1) - - li t1, MC_SDR_MODUL_BASE - - /* disable the controller */ - li t2, 0 - sw t2, MC_CTRLENA(t1) - - li t2, 0x822 - sw t2, MC_IOGP(t1) - - li t2, 0x2 - sw t2, MC_CFGDW(t1) - - /* Set CAS Latency */ - li t2, 0x00000020 - sw t2, MC_MRSCODE(t1) - - /* Set CS0 to SDRAM parameters */ - li t2, 0x000014d8 - sw t2, MC_CFGPB0(t1) - - /* Set SDRAM latency parameters */ - li t2, 0x00036325; /* BC PC100 */ - sw t2, MC_LATENCY(t1) - - /* Set SDRAM refresh rate */ - li t2, 0x00000C30 - sw t2, MC_TREFRESH(t1) - - /* Clear Power-down registers */ - sw zero, MC_SELFRFSH(t1) - - /* Finally enable the controller */ - li t2, 1 - sw t2, MC_CTRLENA(t1) - - j ra - nop - - .end sdram_init - -#endif /* !CONFIG_USE_DDR_RAM */ - -#ifdef CONFIG_USE_DDR_RAM -/* - * void ddrram_init(long) - * - * a0 has the clock value - */ - .globl ddrram_init - .ent ddrram_init -ddrram_init: - - /* DDR-DRAM Initialization - */ - li t1, MC_MODUL_BASE - - /* Clear Error log registers */ - sw zero, MC_ERRCAUSE(t1) - sw zero, MC_ERRADDR(t1) - - /* Enable DDR module in memory controller */ - li t3, MC_DDRRAM_ENABLE - lw t2, MC_CON(t1) - or t3, t2, t3 - sw t3, MC_CON(t1) - - li t1, MC_DDR_MODUL_BASE - - /* Write configuration to DDR controller registers */ - li t2, MC_DC0_VALUE - sw t2, MC_DC00(t1) - - li t2, MC_DC1_VALUE - sw t2, MC_DC01(t1) - - li t2, MC_DC2_VALUE - sw t2, MC_DC02(t1) - - li t2, MC_DC3_VALUE - sw t2, MC_DC03(t1) - - li t2, MC_DC4_VALUE - sw t2, MC_DC04(t1) - - li t2, MC_DC5_VALUE - sw t2, MC_DC05(t1) - - li t2, MC_DC6_VALUE - sw t2, MC_DC06(t1) - - li t2, MC_DC7_VALUE - sw t2, MC_DC07(t1) - - li t2, MC_DC8_VALUE - sw t2, MC_DC08(t1) - - li t2, MC_DC9_VALUE - sw t2, MC_DC09(t1) - - li t2, MC_DC10_VALUE - sw t2, MC_DC10(t1) - - li t2, MC_DC11_VALUE - sw t2, MC_DC11(t1) - - li t2, MC_DC12_VALUE - sw t2, MC_DC12(t1) - - li t2, MC_DC13_VALUE - sw t2, MC_DC13(t1) - - li t2, MC_DC14_VALUE - sw t2, MC_DC14(t1) - - li t2, MC_DC15_VALUE - sw t2, MC_DC15(t1) - - li t2, MC_DC16_VALUE - sw t2, MC_DC16(t1) - - li t2, MC_DC17_VALUE - sw t2, MC_DC17(t1) - - li t2, MC_DC18_VALUE - sw t2, MC_DC18(t1) - - li t2, MC_DC19_VALUE - sw t2, MC_DC19(t1) - - li t2, MC_DC20_VALUE - sw t2, MC_DC20(t1) - - li t2, MC_DC21_VALUE - sw t2, MC_DC21(t1) - - li t2, MC_DC22_VALUE - sw t2, MC_DC22(t1) - - li t2, MC_DC23_VALUE - sw t2, MC_DC23(t1) - - li t2, MC_DC24_VALUE - sw t2, MC_DC24(t1) - - li t2, MC_DC25_VALUE - sw t2, MC_DC25(t1) - - li t2, MC_DC26_VALUE - sw t2, MC_DC26(t1) - - li t2, MC_DC27_VALUE - sw t2, MC_DC27(t1) - - li t2, MC_DC28_VALUE - sw t2, MC_DC28(t1) - - li t2, MC_DC29_VALUE - sw t2, MC_DC29(t1) - - li t2, MC_DC30_VALUE - sw t2, MC_DC30(t1) - - li t2, MC_DC31_VALUE - sw t2, MC_DC31(t1) - - li t2, MC_DC32_VALUE - sw t2, MC_DC32(t1) - - li t2, MC_DC33_VALUE - sw t2, MC_DC33(t1) - - li t2, MC_DC34_VALUE - sw t2, MC_DC34(t1) - - li t2, MC_DC35_VALUE - sw t2, MC_DC35(t1) - - li t2, MC_DC36_VALUE - sw t2, MC_DC36(t1) - - li t2, MC_DC37_VALUE - sw t2, MC_DC37(t1) - - li t2, MC_DC38_VALUE - sw t2, MC_DC38(t1) - - li t2, MC_DC39_VALUE - sw t2, MC_DC39(t1) - - li t2, MC_DC40_VALUE - sw t2, MC_DC40(t1) - - li t2, MC_DC41_VALUE - sw t2, MC_DC41(t1) - - li t2, MC_DC42_VALUE - sw t2, MC_DC42(t1) - - li t2, MC_DC43_VALUE - sw t2, MC_DC43(t1) - - li t2, MC_DC44_VALUE - sw t2, MC_DC44(t1) - - li t2, MC_DC45_VALUE - sw t2, MC_DC45(t1) - - li t2, MC_DC46_VALUE - sw t2, MC_DC46(t1) - - li t2, 0x00000100 - sw t2, MC_DC03(t1) - - j ra - nop - - .end ddrram_init -#endif /* CONFIG_USE_DDR_RAM */ - - .globl lowlevel_init - .ent lowlevel_init -lowlevel_init: - /* EBU, CGU and SDRAM/DDR-RAM Initialization. - */ - move t0, ra - /* We rely on the fact that non of the following ..._init() functions - * modify t0 - */ -#if defined(CONFIG_SYS_EBU_BOOT) -#if defined(DDR166) - /* 0xe8 means CPU0/CPU1 333M, DDR 167M, FPI 83M, PPE 240M */ - li a0,0xe8 -#elif defined(DDR133) - /* 0xe9 means CPU0/CPU1 333M, DDR 133M, FPI 83M, PPE 240M */ - li a0,0xe9 -#else /* defined(DDR111) */ - /* 0xea means CPU0/CPU1 333M, DDR 111M, FPI 83M, PPE 240M */ - li a0,0xea -#endif - bal cgu_init - nop -#endif /* CONFIG_SYS_EBU_BOOT */ - - bal ebu_init - nop - -//06063001-joelin disable the PCI CFRAME mask-start -#ifdef DISABLE_CFRAME - li t1, PCI_CR_PCI //mw bf103034 80000000 - li t2, 0x80000000 - sw t2,0(t1) - - li t1, PCI_CR_PCI_MOD_REG //mw be105430 103 - li t2, 0x103 - sw t2,0(t1) - - li t1, CS_CFM //mw b700006c 0 - li t2, 0x00 - sw t2, 0(t1) - - li t1, PCI_CR_PCI_MOD_REG //mw be105430 103 - li t2, 0x1000103 - sw t2, 0(t1) -#endif -//06063001-joelin disable the PCI CFRAME mask-end - -#ifdef CONFIG_SYS_EBU_BOOT -#ifndef CONFIG_SYS_RAMBOOT -#ifdef CONFIG_USE_DDR_RAM - bal ddrram_init - nop -#else - bal sdram_init - nop -#endif -#endif /* CONFIG_SYS_RAMBOOT */ -#endif /* CONFIG_SYS_EBU_BOOT */ - - move ra, t0 - j ra - nop - - .end lowlevel_init diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/pmuenable.S b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/pmuenable.S deleted file mode 100644 index e0d7971d89..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/pmuenable.S +++ /dev/null @@ -1,48 +0,0 @@ -/* - * Power Management unit initialization code for AMAZON development board. - * - * Copyright (c) 2003 Ou Ke, Infineon. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include - -#define PMU_PWDCR 0xBF10201C -#define PMU_SR 0xBF102020 - - .globl pmuenable - -pmuenable: - li t0, PMU_PWDCR - li t1, 0x2 /* enable everything */ - sw t1, 0(t0) -#if 0 -1: - li t0, PMU_SR - lw t2, 0(t0) - bne t1, t2, 1b - nop -#endif - j ra - nop - - diff --git a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/u-boot.lds b/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/u-boot.lds deleted file mode 100644 index 9a6cd1b8a3..0000000000 --- a/package/uboot-lantiq/files/board/arcadyan/arv752DWP22/u-boot.lds +++ /dev/null @@ -1,70 +0,0 @@ -/* - * (C) Copyright 2003 - * Wolfgang Denk Engineering, - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* -OUTPUT_FORMAT("elf32-bigmips", "elf32-bigmips", "elf32-bigmips") -*/ -OUTPUT_FORMAT("elf32-tradbigmips", "elf32-tradbigmips", "elf32-tradbigmips") -OUTPUT_ARCH(mips) -ENTRY(_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN(4); - .text : - { - *(.text) - } - - . = ALIGN(4); - .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) } - - . = ALIGN(4); - .data : { *(.data) } - - . = .; - _gp = ALIGN(16) + 0x7ff0; - - .got : { - __got_start = .; - *(.got) - __got_end = .; - } - - .sdata : { *(.sdata) } - - .u_boot_cmd : { - __u_boot_cmd_start = .; - *(.u_boot_cmd) - __u_boot_cmd_end = .; - } - - uboot_end_data = .; - num_got_entries = (__got_end - __got_start) >> 2; - - . = ALIGN(4); - .sbss (NOLOAD) : { *(.sbss) } - .bss (NOLOAD) : { *(.bss) . = ALIGN(4); } - uboot_end = .; -} diff --git a/package/uboot-lantiq/files/board/arcadyan/athrs26_phy.c b/package/uboot-lantiq/files/board/arcadyan/athrs26_phy.c new file mode 100644 index 0000000000..2f80ee05e6 --- /dev/null +++ b/package/uboot-lantiq/files/board/arcadyan/athrs26_phy.c @@ -0,0 +1,814 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright © 2003 Atheros Communications, Inc., All Rights Reserved. + */ + +/* + * Manage the atheros ethernet PHY. + * + * All definitions in this file are operating system independent! + */ + +#include +#include +#include +#include +//#include "phy.h" +//#include "ar7100_soc.h" +#include "athrs26_phy.h" + +#define phy_reg_read(base, addr, reg, datap) \ + miiphy_read("lq_cpe_eth", addr, reg, datap); +#define phy_reg_write(base, addr, reg, data) \ + miiphy_write("lq_cpe_eth", addr, reg, data); + + +/* PHY selections and access functions */ + +typedef enum { + PHY_SRCPORT_INFO, + PHY_PORTINFO_SIZE, +} PHY_CAP_TYPE; + +typedef enum { + PHY_SRCPORT_NONE, + PHY_SRCPORT_VLANTAG, + PHY_SRCPORT_TRAILER, +} PHY_SRCPORT_TYPE; + +#ifdef DEBUG +#define DRV_DEBUG 1 +#endif +//#define DRV_DEBUG 1 + +#define DRV_DEBUG_PHYERROR 0x00000001 +#define DRV_DEBUG_PHYCHANGE 0x00000002 +#define DRV_DEBUG_PHYSETUP 0x00000004 + +#if DRV_DEBUG +int athrPhyDebug = DRV_DEBUG_PHYERROR|DRV_DEBUG_PHYCHANGE|DRV_DEBUG_PHYSETUP; + +#define DRV_LOG(FLG, X0, X1, X2, X3, X4, X5, X6) \ +{ \ + if (athrPhyDebug & (FLG)) { \ + logMsg(X0, X1, X2, X3, X4, X5, X6); \ + } \ +} + +#define DRV_MSG(x,a,b,c,d,e,f) \ + logMsg(x,a,b,c,d,e,f) + +#define DRV_PRINT(FLG, X) \ +{ \ + if (athrPhyDebug & (FLG)) { \ + printf X; \ + } \ +} + +#else /* !DRV_DEBUG */ +#define DRV_LOG(DBG_SW, X0, X1, X2, X3, X4, X5, X6) +#define DRV_MSG(x,a,b,c,d,e,f) +#define DRV_PRINT(DBG_SW,X) +#endif + +#define ATHR_LAN_PORT_VLAN 1 +#define ATHR_WAN_PORT_VLAN 2 + +#define ENET_UNIT_LAN 0 + +#define TRUE 1 +#define FALSE 0 + +#define ATHR_PHY0_ADDR 0x0 +#define ATHR_PHY1_ADDR 0x1 +#define ATHR_PHY2_ADDR 0x2 +#define ATHR_PHY3_ADDR 0x3 +#define ATHR_PHY4_ADDR 0x4 + +/* + * Track per-PHY port information. + */ +typedef struct { + BOOL isEnetPort; /* normal enet port */ + BOOL isPhyAlive; /* last known state of link */ + int ethUnit; /* MAC associated with this phy port */ + uint32_t phyBase; + uint32_t phyAddr; /* PHY registers associated with this phy port */ + uint32_t VLANTableSetting; /* Value to be written to VLAN table */ +} athrPhyInfo_t; + +/* + * Per-PHY information, indexed by PHY unit number. + */ +static athrPhyInfo_t athrPhyInfo[] = { + {TRUE, /* phy port 0 -- LAN port 0 */ + FALSE, + ENET_UNIT_LAN, + 0, + ATHR_PHY0_ADDR, + ATHR_LAN_PORT_VLAN + }, + + {TRUE, /* phy port 1 -- LAN port 1 */ + FALSE, + ENET_UNIT_LAN, + 0, + ATHR_PHY1_ADDR, + ATHR_LAN_PORT_VLAN + }, + + {TRUE, /* phy port 2 -- LAN port 2 */ + FALSE, + ENET_UNIT_LAN, + 0, + ATHR_PHY2_ADDR, + ATHR_LAN_PORT_VLAN + }, + + {TRUE, /* phy port 3 -- LAN port 3 */ + FALSE, + ENET_UNIT_LAN, + 0, + ATHR_PHY3_ADDR, + ATHR_LAN_PORT_VLAN + }, + + {TRUE, /* phy port 4 -- WAN port or LAN port 4 */ + FALSE, + 1, + 0, + ATHR_PHY4_ADDR, + ATHR_LAN_PORT_VLAN /* Send to all ports */ + }, + + {FALSE, /* phy port 5 -- CPU port (no RJ45 connector) */ + TRUE, + ENET_UNIT_LAN, + 0, + 0x00, + ATHR_LAN_PORT_VLAN /* Send to all ports */ + }, +}; + +#ifdef CFG_ATHRHDR_EN +typedef struct { + uint8_t data[ATHRHDR_MAX_DATA]; + uint8_t len; + uint32_t seq; +} cmd_resp_t; + +typedef struct { + uint16_t reg_addr; + uint16_t cmd_len; + uint8_t *reg_data; +}cmd_write_t; + +static cmd_write_t cmd_write,cmd_read; +static cmd_resp_t cmd_resp; +static struct eth_device *lan_mac; +//static atomic_t seqcnt = ATOMIC_INIT(0); +static int seqcnt = 0; +static int cmd = 1; +//volatile uchar AthrHdrPkt[60]; +#endif + +#define ATHR_GLOBALREGBASE 0 + +//#define ATHR_PHY_MAX (sizeof(athrPhyInfo) / sizeof(athrPhyInfo[0])) +#define ATHR_PHY_MAX 5 + +/* Range of valid PHY IDs is [MIN..MAX] */ +#define ATHR_ID_MIN 0 +#define ATHR_ID_MAX (ATHR_PHY_MAX-1) + +/* Convenience macros to access myPhyInfo */ +#define ATHR_IS_ENET_PORT(phyUnit) (athrPhyInfo[phyUnit].isEnetPort) +#define ATHR_IS_PHY_ALIVE(phyUnit) (athrPhyInfo[phyUnit].isPhyAlive) +#define ATHR_ETHUNIT(phyUnit) (athrPhyInfo[phyUnit].ethUnit) +#define ATHR_PHYBASE(phyUnit) (athrPhyInfo[phyUnit].phyBase) +#define ATHR_PHYADDR(phyUnit) (athrPhyInfo[phyUnit].phyAddr) +#define ATHR_VLAN_TABLE_SETTING(phyUnit) (athrPhyInfo[phyUnit].VLANTableSetting) + + +#define ATHR_IS_ETHUNIT(phyUnit, ethUnit) \ + (ATHR_IS_ENET_PORT(phyUnit) && \ + ATHR_ETHUNIT(phyUnit) == (ethUnit)) + +#define ATHR_IS_WAN_PORT(phyUnit) (!(ATHR_ETHUNIT(phyUnit)==ENET_UNIT_LAN)) + +/* Forward references */ +BOOL athrs26_phy_is_link_alive(int phyUnit); +static uint32_t athrs26_reg_read(uint16_t reg_addr); +static void athrs26_reg_write(uint16_t reg_addr, + uint32_t reg_val); + +/****************************************************************************** +* +* athrs26_phy_is_link_alive - test to see if the specified link is alive +* +* RETURNS: +* TRUE --> link is alive +* FALSE --> link is down +*/ + +void athrs26_reg_init() +{ + + athrs26_reg_write(0x200, 0x200); + athrs26_reg_write(0x300, 0x200); + athrs26_reg_write(0x400, 0x200); + athrs26_reg_write(0x500, 0x200); + athrs26_reg_write(0x600, 0x7d); + +#ifdef S26_VER_1_0 + phy_reg_write(0, 0, 29, 41); + phy_reg_write(0, 0, 30, 0); + phy_reg_write(0, 1, 29, 41); + phy_reg_write(0, 1, 30, 0); + phy_reg_write(0, 2, 29, 41); + phy_reg_write(0, 2, 30, 0); + phy_reg_write(0, 3, 29, 41); + phy_reg_write(0, 3, 30, 0); + phy_reg_write(0, 4, 29, 41); + phy_reg_write(0, 4, 30, 0); +#endif + + athrs26_reg_write(0x38, 0xc000050e); + +#ifdef CFG_ATHRHDR_EN + athrs26_reg_write(0x104, 0x4804); +#else + athrs26_reg_write(0x104, 0x4004); +#endif + + athrs26_reg_write(0x60, 0xffffffff); + athrs26_reg_write(0x64, 0xaaaaaaaa); + athrs26_reg_write(0x68, 0x55555555); + athrs26_reg_write(0x6c, 0x0); + + athrs26_reg_write(0x70, 0x41af); +} + +BOOL +athrs26_phy_is_link_alive(int phyUnit) +{ + uint16_t phyHwStatus; + uint32_t phyBase; + uint32_t phyAddr; + + phyBase = ATHR_PHYBASE(phyUnit); + phyAddr = ATHR_PHYADDR(phyUnit); + + phy_reg_read(phyBase, phyAddr, ATHR_PHY_SPEC_STATUS, &phyHwStatus); + + if (phyHwStatus & ATHR_STATUS_LINK_PASS) + return TRUE; + + return FALSE; +} + + +/****************************************************************************** +* +* athrs26_phy_setup - reset and setup the PHY associated with +* the specified MAC unit number. +* +* Resets the associated PHY port. +* +* RETURNS: +* TRUE --> associated PHY is alive +* FALSE --> no LINKs on this ethernet unit +*/ + +BOOL +athrs26_phy_setup(int ethUnit) +{ + int phyUnit; + uint16_t phyHwStatus; + uint16_t timeout; + int liveLinks = 0; + uint32_t phyBase = 0; + BOOL foundPhy = FALSE; + uint32_t phyAddr = 0; + uint32_t regVal; + + + /* See if there's any configuration data for this enet */ + /* start auto negogiation on each phy */ + for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { + if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { + continue; + } + + + foundPhy = TRUE; + phyBase = ATHR_PHYBASE(phyUnit); + phyAddr = ATHR_PHYADDR(phyUnit); + + phy_reg_write(phyBase, phyAddr, ATHR_AUTONEG_ADVERT, + ATHR_ADVERTISE_ALL); + + /* Reset PHYs*/ + phy_reg_write(phyBase, phyAddr, ATHR_PHY_CONTROL, + ATHR_CTRL_AUTONEGOTIATION_ENABLE + | ATHR_CTRL_SOFTWARE_RESET); + + } + + if (!foundPhy) { + return FALSE; /* No PHY's configured for this ethUnit */ + } + + /* + * After the phy is reset, it takes a little while before + * it can respond properly. + */ + sysMsDelay(1000); + + /* + * Wait up to .75 seconds for ALL associated PHYs to finish + * autonegotiation. The only way we get out of here sooner is + * if ALL PHYs are connected AND finish autonegotiation. + */ + for (phyUnit=0; (phyUnit < ATHR_PHY_MAX) /*&& (timeout > 0) */; phyUnit++) { + if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { + continue; + } + + timeout=20; + for (;;) { + phyHwStatus = 0; + phy_reg_read(phyBase, phyAddr, ATHR_PHY_CONTROL, &phyHwStatus); + + if (ATHR_RESET_DONE(phyHwStatus)) { + DRV_PRINT(DRV_DEBUG_PHYSETUP, + ("Port %d, Neg Success\n", phyUnit)); + break; + } + if (timeout == 0) { + DRV_PRINT(DRV_DEBUG_PHYSETUP, + ("Port %d, Negogiation timeout\n", phyUnit)); + break; + } + if (--timeout == 0) { + DRV_PRINT(DRV_DEBUG_PHYSETUP, + ("Port %d, Negogiation timeout\n", phyUnit)); + break; + } + + sysMsDelay(150); + } + } + + /* + * All PHYs have had adequate time to autonegotiate. + * Now initialize software status. + * + * It's possible that some ports may take a bit longer + * to autonegotiate; but we can't wait forever. They'll + * get noticed by mv_phyCheckStatusChange during regular + * polling activities. + */ + for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { + if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { + continue; + } + + if (athrs26_phy_is_link_alive(phyUnit)) { + liveLinks++; + ATHR_IS_PHY_ALIVE(phyUnit) = TRUE; + } else { + ATHR_IS_PHY_ALIVE(phyUnit) = FALSE; + } + + phy_reg_read(ATHR_PHYBASE(phyUnit), ATHR_PHYADDR(phyUnit), + ATHR_PHY_SPEC_STATUS, ®Val); + DRV_PRINT(DRV_DEBUG_PHYSETUP, + ("eth%d: Phy Specific Status=%4.4x\n", ethUnit, regVal)); + } +#if 0 + /* if using header for register configuration, we have to */ + /* configure s26 register after frame transmission is enabled */ + + athrs26_reg_write(0x200, 0x200); + athrs26_reg_write(0x300, 0x200); + athrs26_reg_write(0x400, 0x200); + athrs26_reg_write(0x500, 0x200); + athrs26_reg_write(0x600, 0x200); + athrs26_reg_write(0x38, 0x50e); +#endif +#ifndef CFG_ATHRHDR_EN +/* if using header for register configuration, we have to */ + /* configure s26 register after frame transmission is enabled */ + athrs26_reg_init(); +#endif + + return (liveLinks > 0); +} + +/****************************************************************************** +* +* athrs26_phy_is_fdx - Determines whether the phy ports associated with the +* specified device are FULL or HALF duplex. +* +* RETURNS: +* 1 --> FULL +* 0 --> HALF +*/ +int +athrs26_phy_is_fdx(int ethUnit) +{ + int phyUnit; + uint32_t phyBase; + uint32_t phyAddr; + uint16_t phyHwStatus; + int ii = 200; + + if (ethUnit == ENET_UNIT_LAN) + return TRUE; + + for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { + if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { + continue; + } + + if (athrs26_phy_is_link_alive(phyUnit)) { + + phyBase = ATHR_PHYBASE(phyUnit); + phyAddr = ATHR_PHYADDR(phyUnit); + + do { + phy_reg_read(phyBase, phyAddr, ATHR_PHY_SPEC_STATUS, &phyHwStatus); + sysMsDelay(10); + } while((!(phyHwStatus & ATHR_STATUS_RESOVLED)) && --ii); + + if (phyHwStatus & ATHER_STATUS_FULL_DEPLEX) + return TRUE; + } + } + + return FALSE; +} + + +/****************************************************************************** +* +* athrs26_phy_speed - Determines the speed of phy ports associated with the +* specified device. +* +* RETURNS: +* AG7100_PHY_SPEED_10T, AG7100_PHY_SPEED_100TX; +* AG7100_PHY_SPEED_1000T; +*/ + +BOOL +athrs26_phy_speed(int ethUnit) +{ + int phyUnit; + uint16_t phyHwStatus; + uint32_t phyBase; + uint32_t phyAddr; + int ii = 200; + + if (ethUnit == ENET_UNIT_LAN) + return _100BASET; + + for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { + if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { + continue; + } + + if (athrs26_phy_is_link_alive(phyUnit)) { + + phyBase = ATHR_PHYBASE(phyUnit); + phyAddr = ATHR_PHYADDR(phyUnit); + + do { + phy_reg_read(phyBase, phyAddr, + ATHR_PHY_SPEC_STATUS, &phyHwStatus); + sysMsDelay(10); + }while((!(phyHwStatus & ATHR_STATUS_RESOVLED)) && --ii); + + phyHwStatus = ((phyHwStatus & ATHER_STATUS_LINK_MASK) >> + ATHER_STATUS_LINK_SHIFT); + + switch(phyHwStatus) { + case 0: + return _10BASET; + case 1: + return _100BASET; + case 2: + return _1000BASET; + default: + DRV_PRINT(DRV_DEBUG_PHYERROR, ("Unkown speed read!\n")); + } + } + } + + return _10BASET; +} + +/***************************************************************************** +* +* athr_phy_is_up -- checks for significant changes in PHY state. +* +* A "significant change" is: +* dropped link (e.g. ethernet cable unplugged) OR +* autonegotiation completed + link (e.g. ethernet cable plugged in) +* +* When a PHY is plugged in, phyLinkGained is called. +* When a PHY is unplugged, phyLinkLost is called. +*/ + +int +athrs26_phy_is_up(int ethUnit) +{ + int phyUnit; + uint16_t phyHwStatus; + athrPhyInfo_t *lastStatus; + int linkCount = 0; + int lostLinks = 0; + int gainedLinks = 0; + uint32_t phyBase; + uint32_t phyAddr; +#ifdef CFG_ATHRHDR_REG + /* if using header to config s26, the link of MAC0 should always be up */ + if (ethUnit == ENET_UNIT_LAN) + return 1; +#endif + + for (phyUnit=0; phyUnit < ATHR_PHY_MAX; phyUnit++) { + if (!ATHR_IS_ETHUNIT(phyUnit, ethUnit)) { + continue; + } + + phyBase = ATHR_PHYBASE(phyUnit); + phyAddr = ATHR_PHYADDR(phyUnit); + + + lastStatus = &athrPhyInfo[phyUnit]; + phy_reg_read(phyBase, phyAddr, ATHR_PHY_SPEC_STATUS, &phyHwStatus); + + if (lastStatus->isPhyAlive) { /* last known link status was ALIVE */ + /* See if we've lost link */ + if (phyHwStatus & ATHR_STATUS_LINK_PASS) { + linkCount++; + } else { + lostLinks++; + DRV_PRINT(DRV_DEBUG_PHYCHANGE,("\nenet%d port%d down\n", + ethUnit, phyUnit)); + lastStatus->isPhyAlive = FALSE; + } + } else { /* last known link status was DEAD */ + /* Check for reset complete */ + phy_reg_read(phyBase, phyAddr, ATHR_PHY_STATUS, &phyHwStatus); + if (!ATHR_RESET_DONE(phyHwStatus)) + continue; + + /* Check for AutoNegotiation complete */ + if (ATHR_AUTONEG_DONE(phyHwStatus)) { + //printk("autoneg done\n"); + gainedLinks++; + linkCount++; + DRV_PRINT(DRV_DEBUG_PHYCHANGE,("\nenet%d port%d up\n", + ethUnit, phyUnit)); + lastStatus->isPhyAlive = TRUE; + } + } + } + + return (linkCount); + +#if 0 + if (linkCount == 0) { + if (lostLinks) { + /* We just lost the last link for this MAC */ + phyLinkLost(ethUnit); + } + } else { + if (gainedLinks == linkCount) { + /* We just gained our first link(s) for this MAC */ + phyLinkGained(ethUnit); + } + } +#endif +} + +#ifdef CFG_ATHRHDR_EN +void athr_hdr_timeout(void){ + eth_halt(); + NetState = NETLOOP_FAIL; +} + +void athr_hdr_handler(uchar *recv_pkt, unsigned dest, unsigned src, unsigned len){ + header_receive_pkt(recv_pkt); + NetState = NETLOOP_SUCCESS; +} +static int +athrs26_header_config_reg (struct eth_device *dev, uint8_t wr_flag, + uint16_t reg_addr, uint16_t cmd_len, + uint8_t *val) +{ + at_header_t at_header; + reg_cmd_t reg_cmd; + uchar *AthrHdrPkt; + + AthrHdrPkt = NetTxPacket; + + if(AthrHdrPkt == NULL) { + printf("Null packet\n"); + return; + } + memset(AthrHdrPkt,0,60); + + /*fill at_header*/ + at_header.reserved0 = 0x10; //default + at_header.priority = 0; + at_header.type = 0x5; + at_header.broadcast = 0; + at_header.from_cpu = 1; + at_header.reserved1 = 0x01; //default + at_header.port_num = 0; + + AthrHdrPkt[0] = at_header.port_num; + AthrHdrPkt[0] |= at_header.reserved1 << 4; + AthrHdrPkt[0] |= at_header.from_cpu << 6; + AthrHdrPkt[0] |= at_header.broadcast << 7; + + AthrHdrPkt[1] = at_header.type; + AthrHdrPkt[1] |= at_header.priority << 4; + AthrHdrPkt[1] |= at_header.reserved0 << 6; + + + /*fill reg cmd*/ + if(cmd_len > 4) + cmd_len = 4;//only support 32bits register r/w + + reg_cmd.reg_addr = reg_addr&0x3FFFC; + reg_cmd.cmd_len = cmd_len; + reg_cmd.cmd = wr_flag; + reg_cmd.reserved2 = 0x5; //default + reg_cmd.seq_num = seqcnt; + + AthrHdrPkt[2] = reg_cmd.reg_addr & 0xff; + AthrHdrPkt[3] = (reg_cmd.reg_addr & 0xff00) >> 8; + AthrHdrPkt[4] = (reg_cmd.reg_addr & 0x30000) >> 16; + AthrHdrPkt[4] |= reg_cmd.cmd_len << 4; + AthrHdrPkt[5] = reg_cmd.cmd << 4; + AthrHdrPkt[5] |= reg_cmd.reserved2 << 5; + AthrHdrPkt[6] = (reg_cmd.seq_num & 0x7f) << 1; + AthrHdrPkt[7] = (reg_cmd.seq_num & 0x7f80) >> 7; + AthrHdrPkt[8] = (reg_cmd.seq_num & 0x7f8000) >> 15; + AthrHdrPkt[9] = (reg_cmd.seq_num & 0x7f800000) >> 23; + + /*fill reg data*/ + if(!wr_flag)//write + memcpy((AthrHdrPkt + 10), val, cmd_len); + + /*start xmit*/ + if(dev == NULL) { + printf("ERROR device not found\n"); + return -1; + } + header_xmit(dev, AthrHdrPkt ,60); + return 0; +} +void athr_hdr_func(void) { + + NetSetTimeout (1 * CFG_HZ,athr_hdr_timeout ); + NetSetHandler (athr_hdr_handler); + + if(cmd) + athrs26_header_config_reg(lan_mac, cmd, cmd_read.reg_addr, cmd_read.cmd_len, cmd_read.reg_data); + else + athrs26_header_config_reg(lan_mac, cmd, cmd_write.reg_addr, cmd_write.cmd_len, cmd_write.reg_data); +} +static int +athrs26_header_write_reg(uint16_t reg_addr, uint16_t cmd_len, uint8_t *reg_data) +{ + int i = 2; + cmd_write.reg_addr = reg_addr; + cmd_write.cmd_len = cmd_len; + cmd_write.reg_data = reg_data; + cmd = 0; + seqcnt++; + + do { + if (NetLoop(ATHRHDR) >= 0) /* polls for read/write ack from PHY */ + break; + } while (i--); + + return i; +} + +static int +athrs26_header_read_reg(uint16_t reg_addr, uint16_t cmd_len, uint8_t *reg_data) +{ + int i = 2; + + cmd_read.reg_addr = reg_addr; + cmd_read.cmd_len = cmd_len; + cmd_read.reg_data = reg_data; + cmd = 1; + seqcnt++; + + do { + if (NetLoop(ATHRHDR) >= 0) /* polls for read/write ack from PHY */ + break; + } while (i--); + + if ((i==0) || (seqcnt != cmd_resp.seq) || (cmd_len != cmd_resp.len)) { + return -1; + } + memcpy (cmd_read.reg_data, cmd_resp.data, cmd_len); + return 0; +} +int header_receive_pkt(uchar *recv_pkt) +{ + cmd_resp.len = recv_pkt[4] >> 4; + if (cmd_resp.len > 10) + goto out; + + cmd_resp.seq = recv_pkt[6] >> 1; + cmd_resp.seq |= recv_pkt[7] << 7; + cmd_resp.seq |= recv_pkt[8] << 15; + cmd_resp.seq |= recv_pkt[9] << 23; + + if (cmd_resp.seq < seqcnt) + goto out; + memcpy (cmd_resp.data, (recv_pkt + 10), cmd_resp.len); +out: + return 0; +} + +void athrs26_reg_dev(struct eth_device *mac) +{ + lan_mac = mac; +} + +#endif + +static uint32_t +athrs26_reg_read(uint16_t reg_addr) +{ +#ifndef CFG_ATHRHDR_REG + uint16_t reg_word_addr = reg_addr / 2, phy_val; + uint32_t phy_addr; + uint8_t phy_reg; + + /* configure register high address */ + phy_addr = 0x18; + phy_reg = 0x0; + phy_val = (reg_word_addr >> 8) & 0x1ff; /* bit16-8 of reg address*/ + phy_reg_write (0, phy_addr, phy_reg, phy_val); + + /* read register with low address */ + phy_addr = 0x10 | ((reg_word_addr >> 5) & 0x7); /* bit7-5 of reg address */ + phy_reg = reg_word_addr & 0x1f; /* bit 4-0 of reg address*/ + phy_reg_read(0, phy_addr, phy_reg, &phy_val); + + return phy_val; +#else + uint8_t reg_data[4]; + + memset (reg_data, 0, 4); + athrs26_header_read_reg(reg_addr, 4, reg_data); + return (reg_data[0] | (reg_data[1] << 8) | (reg_data[2] << 16) | (reg_data[3] << 24)); +#endif +} + +static void +athrs26_reg_write(uint16_t reg_addr, uint32_t reg_val) +{ +#ifndef CFG_ATHRHDR_REG + uint16_t reg_word_addr = reg_addr / 2, phy_val; + uint32_t phy_addr; + uint8_t phy_reg; + + /* configure register high address */ + phy_addr = 0x18; + phy_reg = 0x0; + phy_val = (reg_word_addr >> 8) & 0x1ff; /* bit16-8 of reg address*/ + phy_reg_write (0, phy_addr, phy_reg, phy_val); + + /* read register with low address */ + phy_addr = 0x10 | ((reg_word_addr >> 5) & 0x7); /* bit7-5 of reg address */ + phy_reg = reg_word_addr & 0x1f; /* bit 4-0 of reg address */ + phy_reg_write (0, phy_addr, phy_reg, reg_val); +#else + uint8_t reg_data[4]; + + memset (reg_data, 0, 4); + reg_data[0] = (uint8_t)(0x00ff & reg_val); + reg_data[1] = (uint8_t)((0xff00 & reg_val) >> 8); + reg_data[2] = (uint8_t)((0xff0000 & reg_val) >> 16); + reg_data[3] = (uint8_t)((0xff000000 & reg_val) >> 24); + + athrs26_header_write_reg (reg_addr, 4, reg_data); +#endif + +} + diff --git a/package/uboot-lantiq/files/board/arcadyan/athrs26_phy.h b/package/uboot-lantiq/files/board/arcadyan/athrs26_phy.h new file mode 100644 index 0000000000..0fdde376eb --- /dev/null +++ b/package/uboot-lantiq/files/board/arcadyan/athrs26_phy.h @@ -0,0 +1,134 @@ +#ifndef _ATHRS26_PHY_H +#define _ATHRS26_PHY_H + +/*****************/ +/* PHY Registers */ +/*****************/ +#define ATHR_PHY_CONTROL 0 +#define ATHR_PHY_STATUS 1 +#define ATHR_PHY_ID1 2 +#define ATHR_PHY_ID2 3 +#define ATHR_AUTONEG_ADVERT 4 +#define ATHR_LINK_PARTNER_ABILITY 5 +#define ATHR_AUTONEG_EXPANSION 6 +#define ATHR_NEXT_PAGE_TRANSMIT 7 +#define ATHR_LINK_PARTNER_NEXT_PAGE 8 +#define ATHR_1000BASET_CONTROL 9 +#define ATHR_1000BASET_STATUS 10 +#define ATHR_PHY_SPEC_CONTROL 16 +#define ATHR_PHY_SPEC_STATUS 17 +#define ATHR_DEBUG_PORT_ADDRESS 29 +#define ATHR_DEBUG_PORT_DATA 30 + +/* ATHR_PHY_CONTROL fields */ +#define ATHR_CTRL_SOFTWARE_RESET 0x8000 +#define ATHR_CTRL_SPEED_LSB 0x2000 +#define ATHR_CTRL_AUTONEGOTIATION_ENABLE 0x1000 +#define ATHR_CTRL_RESTART_AUTONEGOTIATION 0x0200 +#define ATHR_CTRL_SPEED_FULL_DUPLEX 0x0100 +#define ATHR_CTRL_SPEED_MSB 0x0040 + +#define ATHR_RESET_DONE(phy_control) \ + (((phy_control) & (ATHR_CTRL_SOFTWARE_RESET)) == 0) + +/* Phy status fields */ +#define ATHR_STATUS_AUTO_NEG_DONE 0x0020 + +#define ATHR_AUTONEG_DONE(ip_phy_status) \ + (((ip_phy_status) & \ + (ATHR_STATUS_AUTO_NEG_DONE)) == \ + (ATHR_STATUS_AUTO_NEG_DONE)) + +/* Link Partner ability */ +#define ATHR_LINK_100BASETX_FULL_DUPLEX 0x0100 +#define ATHR_LINK_100BASETX 0x0080 +#define ATHR_LINK_10BASETX_FULL_DUPLEX 0x0040 +#define ATHR_LINK_10BASETX 0x0020 + +/* Advertisement register. */ +#define ATHR_ADVERTISE_NEXT_PAGE 0x8000 +#define ATHR_ADVERTISE_ASYM_PAUSE 0x0800 +#define ATHR_ADVERTISE_PAUSE 0x0400 +#define ATHR_ADVERTISE_100FULL 0x0100 +#define ATHR_ADVERTISE_100HALF 0x0080 +#define ATHR_ADVERTISE_10FULL 0x0040 +#define ATHR_ADVERTISE_10HALF 0x0020 + +#define ATHR_ADVERTISE_ALL (ATHR_ADVERTISE_10HALF | ATHR_ADVERTISE_10FULL | \ + ATHR_ADVERTISE_100HALF | ATHR_ADVERTISE_100FULL) + +/* 1000BASET_CONTROL */ +#define ATHR_ADVERTISE_1000FULL 0x0200 + +/* Phy Specific status fields */ +#define ATHER_STATUS_LINK_MASK 0xC000 +#define ATHER_STATUS_LINK_SHIFT 14 +#define ATHER_STATUS_FULL_DEPLEX 0x2000 +#define ATHR_STATUS_LINK_PASS 0x0400 +#define ATHR_STATUS_RESOVLED 0x0800 + +/*phy debug port register */ +#define ATHER_DEBUG_SERDES_REG 5 + +/* Serdes debug fields */ +#define ATHER_SERDES_BEACON 0x0100 + +#ifndef BOOL +#define BOOL int +#define TRUE 1 +#define FALSE 0 +#endif + +#define sysMsDelay(_x) udelay((_x) * 1000) + +#undef S26_VER_1_0 + +#ifdef CFG_ATHRHDR_EN + +#include +#define header_xmit(dev,pkt,len) dev->send(dev,pkt,len) //dev_queue_xmit(skb) +#define header_recv_ack(dev) dev->recv(dev) //dev_queue_xmit(skb) + +typedef enum { + NORMAL_PACKET, + RESERVED0, + MIB_1ST, + RESERVED1, + RESERVED2, + READ_WRITE_REG, + READ_WRITE_REG_ACK, + RESERVED3 +} ATHR_HDR_TYPE; + +typedef struct { + uint16_t reserved0; + uint16_t priority; + uint16_t type ; + uint16_t broadcast; + uint16_t from_cpu; + uint16_t reserved1; + uint16_t port_num; +}at_header_t; + +typedef struct { + uint64_t reg_addr; + uint64_t reserved0; + uint64_t cmd_len; + uint64_t reserved1; + uint64_t cmd; + uint64_t reserved2; + uint64_t seq_num; +}reg_cmd_t; +void athrs26_reg_init(void); +int header_receive_pkt(uchar *pkt); +void athrs26_reg_dev(struct eth_device *mac); + +#endif + +int athrs26_phy_is_up(int unit); +int athrs26_phy_is_fdx(int unit); +int athrs26_phy_speed(int unit); +BOOL athrs26_phy_setup(int unit); + +#endif /* _ATHRS26_PHY_H */ + diff --git a/package/uboot-lantiq/files/board/arcadyan/board.c b/package/uboot-lantiq/files/board/arcadyan/board.c new file mode 100644 index 0000000000..cf0cbce7d6 --- /dev/null +++ b/package/uboot-lantiq/files/board/arcadyan/board.c @@ -0,0 +1,406 @@ +/* + * (C) Copyright 2003 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2010 + * Thomas Langer, Ralph Hempel + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#if defined(CONFIG_CMD_HTTPD) +#include +#endif +#if defined(CONFIG_PCI) +#include +#endif +#if defined(CONFIG_AR8216_SWITCH) +#include "athrs26_phy.h" +#endif + +extern ulong ifx_get_ddr_hz(void); +extern ulong ifx_get_cpuclk(void); + +/* IDs and registers of known external switches */ +void _machine_restart(void) +{ + *DANUBE_RCU_RST_REQ |=1<<30; +} + +#ifdef CONFIG_SYS_RAMBOOT +phys_size_t initdram(int board_type) +{ + return get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM); +} +#elif defined(CONFIG_USE_DDR_RAM) +phys_size_t initdram(int board_type) +{ + return (CONFIG_SYS_MAX_RAM); +} +#else + +static ulong max_sdram_size(void) /* per Chip Select */ +{ + /* The only supported SDRAM data width is 16bit. + */ +#define CFG_DW 4 + + /* The only supported number of SDRAM banks is 4. + */ +#define CFG_NB 4 + + ulong cfgpb0 = *DANUBE_SDRAM_MC_CFGPB0; + int cols = cfgpb0 & 0xF; + int rows = (cfgpb0 & 0xF0) >> 4; + ulong size = (1 << (rows + cols)) * CFG_DW * CFG_NB; + + return size; +} + +/* + * Check memory range for valid RAM. A simple memory test determines + * the actually available RAM size between addresses `base' and + * `base + maxsize'. + */ + +static long int dram_size(long int *base, long int maxsize) +{ + volatile long int *addr; + ulong cnt, val; + ulong save[32]; /* to make test non-destructive */ + unsigned char i = 0; + + for (cnt = (maxsize / sizeof (long)) >> 1; cnt > 0; cnt >>= 1) { + addr = base + cnt; /* pointer arith! */ + + save[i++] = *addr; + *addr = ~cnt; + } + + /* write 0 to base address */ + addr = base; + save[i] = *addr; + *addr = 0; + + /* check at base address */ + if ((val = *addr) != 0) { + *addr = save[i]; + return (0); + } + + for (cnt = 1; cnt < maxsize / sizeof (long); cnt <<= 1) { + addr = base + cnt; /* pointer arith! */ + + val = *addr; + *addr = save[--i]; + + if (val != (~cnt)) { + return (cnt * sizeof (long)); + } + } + return (maxsize); +} + +phys_size_t initdram(int board_type) +{ + int rows, cols, best_val = *DANUBE_SDRAM_MC_CFGPB0; + ulong size, max_size = 0; + ulong our_address; + + /* load t9 into our_address */ + asm volatile ("move %0, $25" : "=r" (our_address) :); + + /* Can't probe for RAM size unless we are running from Flash. + * find out whether running from DRAM or Flash. + */ + if (CPHYSADDR(our_address) < CPHYSADDR(PHYS_FLASH_1)) + { + return max_sdram_size(); + } + + for (cols = 0x8; cols <= 0xC; cols++) + { + for (rows = 0xB; rows <= 0xD; rows++) + { + *DANUBE_SDRAM_MC_CFGPB0 = (0x14 << 8) | + (rows << 4) | cols; + size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, + max_sdram_size()); + + if (size > max_size) + { + best_val = *DANUBE_SDRAM_MC_CFGPB0; + max_size = size; + } + } + } + + *DANUBE_SDRAM_MC_CFGPB0 = best_val; + return max_size; +} +#endif + +static void gpio_default(void) +{ +#ifdef CONFIG_SWITCH_PORT0 + *DANUBE_GPIO_P0_ALTSEL0 &= ~(1< + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +/* History: + peng liu May 25, 2006, for PLL setting after reset, 05252006 + */ +#include +#include +#include + +#if 0 + +#if defined(CONFIG_USE_DDR_RAM) + +#if defined(CONFIG_USE_DDR_RAM_CFG_111M) +#include "ddr_settings_r111.h" +#define DDR111 +#elif defined(CONFIG_USE_DDR_RAM_CFG_166M) +#include "ddr_settings_r166.h" +#define DDR166 +#elif defined(CONFIG_USE_DDR_RAM_CFG_e111M) +#include "ddr_settings_e111.h" +#define DDR111 +#elif defined(CONFIG_USE_DDR_RAM_CFG_e166M) +#include "ddr_settings_e166.h" +#define DDR166 +#elif defined(CONFIG_USE_DDR_RAM_CFG_promos400) +#include "ddr_settings_PROMOSDDR400.h" +#define DDR166 +#elif defined(CONFIG_USE_DDR_RAM_CFG_samsung166) +#include "ddr_settings_Samsung_166.h" +#define DDR166 +#elif defined(CONFIG_USE_DDR_RAM_CFG_psc166) +#include "ddr_settings_psc_166.h" +#define DDR166 +#else +#warning "missing definition for ddr_settings.h, use default!" +#include "ddr_settings.h" +#endif +#endif /* CONFIG_USE_DDR_RAM */ + +#else + +#include "ddr_settings_psc_166.h" +#define DDR166 + +#endif + +#if defined(CONFIG_USE_DDR_RAM) && !defined(MC_DC0_VALUE) +#error "missing include of ddr_settings.h" +#endif + +#define EBU_MODUL_BASE 0xBE105300 +#define EBU_CLC(value) 0x0000(value) +#define EBU_CON(value) 0x0010(value) +#define EBU_ADDSEL0(value) 0x0020(value) +#define EBU_ADDSEL1(value) 0x0024(value) +#define EBU_ADDSEL2(value) 0x0028(value) +#define EBU_ADDSEL3(value) 0x002C(value) +#define EBU_BUSCON0(value) 0x0060(value) +#define EBU_BUSCON1(value) 0x0064(value) +#define EBU_BUSCON2(value) 0x0068(value) +#define EBU_BUSCON3(value) 0x006C(value) + +#define MC_MODUL_BASE 0xBF800000 +#define MC_ERRCAUSE(value) 0x0010(value) +#define MC_ERRADDR(value) 0x0020(value) +#define MC_CON(value) 0x0060(value) + +#define MC_SRAM_ENABLE 0x00000004 +#define MC_SDRAM_ENABLE 0x00000002 +#define MC_DDRRAM_ENABLE 0x00000001 + +#define MC_SDR_MODUL_BASE 0xBF800200 +#define MC_IOGP(value) 0x0000(value) +#define MC_CTRLENA(value) 0x0010(value) +#define MC_MRSCODE(value) 0x0020(value) +#define MC_CFGDW(value) 0x0030(value) +#define MC_CFGPB0(value) 0x0040(value) +#define MC_LATENCY(value) 0x0080(value) +#define MC_TREFRESH(value) 0x0090(value) +#define MC_SELFRFSH(value) 0x00A0(value) + +#define MC_DDR_MODUL_BASE 0xBF801000 +#define MC_DC00(value) 0x0000(value) +#define MC_DC01(value) 0x0010(value) +#define MC_DC02(value) 0x0020(value) +#define MC_DC03(value) 0x0030(value) +#define MC_DC04(value) 0x0040(value) +#define MC_DC05(value) 0x0050(value) +#define MC_DC06(value) 0x0060(value) +#define MC_DC07(value) 0x0070(value) +#define MC_DC08(value) 0x0080(value) +#define MC_DC09(value) 0x0090(value) +#define MC_DC10(value) 0x00A0(value) +#define MC_DC11(value) 0x00B0(value) +#define MC_DC12(value) 0x00C0(value) +#define MC_DC13(value) 0x00D0(value) +#define MC_DC14(value) 0x00E0(value) +#define MC_DC15(value) 0x00F0(value) +#define MC_DC16(value) 0x0100(value) +#define MC_DC17(value) 0x0110(value) +#define MC_DC18(value) 0x0120(value) +#define MC_DC19(value) 0x0130(value) +#define MC_DC20(value) 0x0140(value) +#define MC_DC21(value) 0x0150(value) +#define MC_DC22(value) 0x0160(value) +#define MC_DC23(value) 0x0170(value) +#define MC_DC24(value) 0x0180(value) +#define MC_DC25(value) 0x0190(value) +#define MC_DC26(value) 0x01A0(value) +#define MC_DC27(value) 0x01B0(value) +#define MC_DC28(value) 0x01C0(value) +#define MC_DC29(value) 0x01D0(value) +#define MC_DC30(value) 0x01E0(value) +#define MC_DC31(value) 0x01F0(value) +#define MC_DC32(value) 0x0200(value) +#define MC_DC33(value) 0x0210(value) +#define MC_DC34(value) 0x0220(value) +#define MC_DC35(value) 0x0230(value) +#define MC_DC36(value) 0x0240(value) +#define MC_DC37(value) 0x0250(value) +#define MC_DC38(value) 0x0260(value) +#define MC_DC39(value) 0x0270(value) +#define MC_DC40(value) 0x0280(value) +#define MC_DC41(value) 0x0290(value) +#define MC_DC42(value) 0x02A0(value) +#define MC_DC43(value) 0x02B0(value) +#define MC_DC44(value) 0x02C0(value) +#define MC_DC45(value) 0x02D0(value) +#define MC_DC46(value) 0x02E0(value) + +#define RCU_OFFSET 0xBF203000 +#define RCU_RST_REQ (RCU_OFFSET + 0x0010) +#define RCU_STS (RCU_OFFSET + 0x0014) + +#define CGU_OFFSET 0xBF103000 +#define PLL0_CFG (CGU_OFFSET + 0x0004) +#define PLL1_CFG (CGU_OFFSET + 0x0008) +#define PLL2_CFG (CGU_OFFSET + 0x000C) +#define CGU_SYS (CGU_OFFSET + 0x0010) +#define CGU_UPDATE (CGU_OFFSET + 0x0014) +#define IF_CLK (CGU_OFFSET + 0x0018) +#define CGU_SMD (CGU_OFFSET + 0x0020) +#define CGU_CT1SR (CGU_OFFSET + 0x0028) +#define CGU_CT2SR (CGU_OFFSET + 0x002C) +#define CGU_PCMCR (CGU_OFFSET + 0x0030) +#define PCI_CR_PCI (CGU_OFFSET + 0x0034) +#define CGU_OSC_CTRL (CGU_OFFSET + 0x001C) +#define CGU_MIPS_PWR_DWN (CGU_OFFSET + 0x0038) +#define CLK_MEASURE (CGU_OFFSET + 0x003C) + +//05252006 +#define pll0_35MHz_CONFIG 0x9D861059 +#define pll1_35MHz_CONFIG 0x1A260CD9 +#define pll2_35MHz_CONFIG 0x8000f1e5 +#define pll0_36MHz_CONFIG 0x1000125D +#define pll1_36MHz_CONFIG 0x1B1E0C99 +#define pll2_36MHz_CONFIG 0x8002f2a1 +//05252006 + +//06063001-joelin disable the PCI CFRAME mask -start +/*CFRAME is an I/O signal, in the chip, the output CFRAME is selected via GPIO altsel pins, so if you select MII1 RXD1, the CFRAME will not come out. +But the CFRAME input still take the signal from the pad and not disabled when altsel choose other function. So when MII1_RXD1 is low from other device, the EBU interface will be disabled. + +The chip function in such a way that disable the CFRAME mask mean EBU not longer check CFRAME to be the device using the bus. +The side effect is the entire PCI block will see CFRAME low all the time meaning PCI cannot use the bus at all so no more PCI function. +*/ +#define PCI_CR_PR_OFFSET 0xBE105400 +#define PCI_CR_PCI_MOD_REG (PCI_CR_PR_OFFSET + 0x0030) +#define PCI_CONFIG_SPACE 0xB7000000 +#define CS_CFM (PCI_CONFIG_SPACE + 0x6C) +//06063001-joelin disable the PCI CFRAME mask -end + .set noreorder + + +/* + * void ebu_init(void) + */ + .globl ebu_init + .ent ebu_init +ebu_init: + +#if defined(CONFIG_EBU_ADDSEL0) || defined(CONFIG_EBU_ADDSEL1) || \ + defined(CONFIG_EBU_ADDSEL2) || defined(CONFIG_EBU_ADDSEL3) || \ + defined(CONFIG_EBU_BUSCON0) || defined(CONFIG_EBU_BUSCON1) || \ + defined(CONFIG_EBU_BUSCON2) || defined(CONFIG_EBU_BUSCON3) + + li t1, EBU_MODUL_BASE +#if defined(CONFIG_EBU_ADDSEL0) + li t2, CONFIG_EBU_ADDSEL0 + sw t2, EBU_ADDSEL0(t1) +#endif +#if defined(CONFIG_EBU_ADDSEL1) + li t2, CONFIG_EBU_ADDSEL1 + sw t2, EBU_ADDSEL1(t1) +#endif +#if defined(CONFIG_EBU_ADDSEL2) + li t2, CONFIG_EBU_ADDSEL2 + sw t2, EBU_ADDSEL2(t1) +#endif +#if defined(CONFIG_EBU_ADDSEL3) + li t2, CONFIG_EBU_ADDSEL3 + sw t2, EBU_ADDSEL3(t1) +#endif + +#if defined(CONFIG_EBU_BUSCON0) + li t2, CONFIG_EBU_BUSCON0 + sw t2, EBU_BUSCON0(t1) +#endif +#if defined(CONFIG_EBU_BUSCON1) + li t2, CONFIG_EBU_BUSCON1 + sw t2, EBU_BUSCON1(t1) +#endif +#if defined(CONFIG_EBU_BUSCON2) + li t2, CONFIG_EBU_BUSCON2 + sw t2, EBU_BUSCON2(t1) +#endif +#if defined(CONFIG_EBU_BUSCON3) + li t2, CONFIG_EBU_BUSCON3 + sw t2, EBU_BUSCON3(t1) +#endif + +#endif + + j ra + nop + + .end ebu_init + + +/* + * void cgu_init(long) + * + * a0 has the clock value + */ + .globl cgu_init + .ent cgu_init +cgu_init: + li t2, CGU_SYS + lw t2,0(t2) + beq t2,a0,freq_up2date + nop + + li t2, RCU_STS + lw t2, 0(t2) + and t2,0x00020000 + beq t2,0x00020000,boot_36MHZ + nop +//05252006 + li t1, PLL0_CFG + li t2, pll0_35MHz_CONFIG + sw t2,0(t1) + li t1, PLL1_CFG + li t2, pll1_35MHz_CONFIG + sw t2,0(t1) + li t1, PLL2_CFG + li t2, pll2_35MHz_CONFIG + sw t2,0(t1) + li t1, CGU_SYS + sw a0,0(t1) + li t1, RCU_RST_REQ + li t2, 0x40000008 + sw t2,0(t1) + b wait_reset + nop +boot_36MHZ: + li t1, PLL0_CFG + li t2, pll0_36MHz_CONFIG + sw t2,0(t1) + li t1, PLL1_CFG + li t2, pll1_36MHz_CONFIG + sw t2,0(t1) + li t1, PLL2_CFG + li t2, pll2_36MHz_CONFIG + sw t2,0(t1) + li t1, CGU_SYS + sw a0,0(t1) + li t1, RCU_RST_REQ + li t2, 0x40000008 + sw t2,0(t1) +//05252006 + +wait_reset: + b wait_reset + nop +freq_up2date: + j ra + nop + + .end cgu_init + +#ifndef CONFIG_USE_DDR_RAM +/* + * void sdram_init(long) + * + * a0 has the clock value + */ + .globl sdram_init + .ent sdram_init +sdram_init: + + /* SDRAM Initialization + */ + li t1, MC_MODUL_BASE + + /* Clear Error log registers */ + sw zero, MC_ERRCAUSE(t1) + sw zero, MC_ERRADDR(t1) + + /* Enable SDRAM module in memory controller */ + li t3, MC_SDRAM_ENABLE + lw t2, MC_CON(t1) + or t3, t2, t3 + sw t3, MC_CON(t1) + + li t1, MC_SDR_MODUL_BASE + + /* disable the controller */ + li t2, 0 + sw t2, MC_CTRLENA(t1) + + li t2, 0x822 + sw t2, MC_IOGP(t1) + + li t2, 0x2 + sw t2, MC_CFGDW(t1) + + /* Set CAS Latency */ + li t2, 0x00000020 + sw t2, MC_MRSCODE(t1) + + /* Set CS0 to SDRAM parameters */ + li t2, 0x000014d8 + sw t2, MC_CFGPB0(t1) + + /* Set SDRAM latency parameters */ + li t2, 0x00036325; /* BC PC100 */ + sw t2, MC_LATENCY(t1) + + /* Set SDRAM refresh rate */ + li t2, 0x00000C30 + sw t2, MC_TREFRESH(t1) + + /* Clear Power-down registers */ + sw zero, MC_SELFRFSH(t1) + + /* Finally enable the controller */ + li t2, 1 + sw t2, MC_CTRLENA(t1) + + j ra + nop + + .end sdram_init + +#endif /* !CONFIG_USE_DDR_RAM */ + +#ifdef CONFIG_USE_DDR_RAM +/* + * void ddrram_init(long) + * + * a0 has the clock value + */ + .globl ddrram_init + .ent ddrram_init +ddrram_init: + + /* DDR-DRAM Initialization + */ + li t1, MC_MODUL_BASE + + /* Clear Error log registers */ + sw zero, MC_ERRCAUSE(t1) + sw zero, MC_ERRADDR(t1) + + /* Enable DDR module in memory controller */ + li t3, MC_DDRRAM_ENABLE + lw t2, MC_CON(t1) + or t3, t2, t3 + sw t3, MC_CON(t1) + + li t1, MC_DDR_MODUL_BASE + + /* Write configuration to DDR controller registers */ + li t2, MC_DC0_VALUE + sw t2, MC_DC00(t1) + + li t2, MC_DC1_VALUE + sw t2, MC_DC01(t1) + + li t2, MC_DC2_VALUE + sw t2, MC_DC02(t1) + + li t2, MC_DC3_VALUE + sw t2, MC_DC03(t1) + + li t2, MC_DC4_VALUE + sw t2, MC_DC04(t1) + + li t2, MC_DC5_VALUE + sw t2, MC_DC05(t1) + + li t2, MC_DC6_VALUE + sw t2, MC_DC06(t1) + + li t2, MC_DC7_VALUE + sw t2, MC_DC07(t1) + + li t2, MC_DC8_VALUE + sw t2, MC_DC08(t1) + + li t2, MC_DC9_VALUE + sw t2, MC_DC09(t1) + + li t2, MC_DC10_VALUE + sw t2, MC_DC10(t1) + + li t2, MC_DC11_VALUE + sw t2, MC_DC11(t1) + + li t2, MC_DC12_VALUE + sw t2, MC_DC12(t1) + + li t2, MC_DC13_VALUE + sw t2, MC_DC13(t1) + + li t2, MC_DC14_VALUE + sw t2, MC_DC14(t1) + + li t2, MC_DC15_VALUE + sw t2, MC_DC15(t1) + + li t2, MC_DC16_VALUE + sw t2, MC_DC16(t1) + + li t2, MC_DC17_VALUE + sw t2, MC_DC17(t1) + + li t2, MC_DC18_VALUE + sw t2, MC_DC18(t1) + + li t2, MC_DC19_VALUE + sw t2, MC_DC19(t1) + + li t2, MC_DC20_VALUE + sw t2, MC_DC20(t1) + + li t2, MC_DC21_VALUE + sw t2, MC_DC21(t1) + + li t2, MC_DC22_VALUE + sw t2, MC_DC22(t1) + + li t2, MC_DC23_VALUE + sw t2, MC_DC23(t1) + + li t2, MC_DC24_VALUE + sw t2, MC_DC24(t1) + + li t2, MC_DC25_VALUE + sw t2, MC_DC25(t1) + + li t2, MC_DC26_VALUE + sw t2, MC_DC26(t1) + + li t2, MC_DC27_VALUE + sw t2, MC_DC27(t1) + + li t2, MC_DC28_VALUE + sw t2, MC_DC28(t1) + + li t2, MC_DC29_VALUE + sw t2, MC_DC29(t1) + + li t2, MC_DC30_VALUE + sw t2, MC_DC30(t1) + + li t2, MC_DC31_VALUE + sw t2, MC_DC31(t1) + + li t2, MC_DC32_VALUE + sw t2, MC_DC32(t1) + + li t2, MC_DC33_VALUE + sw t2, MC_DC33(t1) + + li t2, MC_DC34_VALUE + sw t2, MC_DC34(t1) + + li t2, MC_DC35_VALUE + sw t2, MC_DC35(t1) + + li t2, MC_DC36_VALUE + sw t2, MC_DC36(t1) + + li t2, MC_DC37_VALUE + sw t2, MC_DC37(t1) + + li t2, MC_DC38_VALUE + sw t2, MC_DC38(t1) + + li t2, MC_DC39_VALUE + sw t2, MC_DC39(t1) + + li t2, MC_DC40_VALUE + sw t2, MC_DC40(t1) + + li t2, MC_DC41_VALUE + sw t2, MC_DC41(t1) + + li t2, MC_DC42_VALUE + sw t2, MC_DC42(t1) + + li t2, MC_DC43_VALUE + sw t2, MC_DC43(t1) + + li t2, MC_DC44_VALUE + sw t2, MC_DC44(t1) + + li t2, MC_DC45_VALUE + sw t2, MC_DC45(t1) + + li t2, MC_DC46_VALUE + sw t2, MC_DC46(t1) + + li t2, 0x00000100 + sw t2, MC_DC03(t1) + + j ra + nop + + .end ddrram_init +#endif /* CONFIG_USE_DDR_RAM */ + + .globl lowlevel_init + .ent lowlevel_init +lowlevel_init: + /* EBU, CGU and SDRAM/DDR-RAM Initialization. + */ + move t0, ra + /* We rely on the fact that non of the following ..._init() functions + * modify t0 + */ +#if defined(CONFIG_SYS_EBU_BOOT) +#if defined(DDR166) + /* 0xe8 means CPU0/CPU1 333M, DDR 167M, FPI 83M, PPE 240M */ + li a0,0xe8 +#elif defined(DDR133) + /* 0xe9 means CPU0/CPU1 333M, DDR 133M, FPI 83M, PPE 240M */ + li a0,0xe9 +#else /* defined(DDR111) */ + /* 0xea means CPU0/CPU1 333M, DDR 111M, FPI 83M, PPE 240M */ + li a0,0xea +#endif + bal cgu_init + nop +#endif /* CONFIG_SYS_EBU_BOOT */ + + bal ebu_init + nop + +//06063001-joelin disable the PCI CFRAME mask-start +#ifdef DISABLE_CFRAME + li t1, PCI_CR_PCI //mw bf103034 80000000 + li t2, 0x80000000 + sw t2,0(t1) + + li t1, PCI_CR_PCI_MOD_REG //mw be105430 103 + li t2, 0x103 + sw t2,0(t1) + + li t1, CS_CFM //mw b700006c 0 + li t2, 0x00 + sw t2, 0(t1) + + li t1, PCI_CR_PCI_MOD_REG //mw be105430 103 + li t2, 0x1000103 + sw t2, 0(t1) +#endif +//06063001-joelin disable the PCI CFRAME mask-end + +#ifdef CONFIG_SYS_EBU_BOOT +#ifndef CONFIG_SYS_RAMBOOT +#ifdef CONFIG_USE_DDR_RAM + bal ddrram_init + nop +#else + bal sdram_init + nop +#endif +#endif /* CONFIG_SYS_RAMBOOT */ +#endif /* CONFIG_SYS_EBU_BOOT */ + + move ra, t0 + j ra + nop + + .end lowlevel_init diff --git a/package/uboot-lantiq/files/board/arcadyan/pmuenable.S b/package/uboot-lantiq/files/board/arcadyan/pmuenable.S new file mode 100644 index 0000000000..e0d7971d89 --- /dev/null +++ b/package/uboot-lantiq/files/board/arcadyan/pmuenable.S @@ -0,0 +1,48 @@ +/* + * Power Management unit initialization code for AMAZON development board. + * + * Copyright (c) 2003 Ou Ke, Infineon. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +#define PMU_PWDCR 0xBF10201C +#define PMU_SR 0xBF102020 + + .globl pmuenable + +pmuenable: + li t0, PMU_PWDCR + li t1, 0x2 /* enable everything */ + sw t1, 0(t0) +#if 0 +1: + li t0, PMU_SR + lw t2, 0(t0) + bne t1, t2, 1b + nop +#endif + j ra + nop + + diff --git a/package/uboot-lantiq/files/board/arcadyan/u-boot.lds b/package/uboot-lantiq/files/board/arcadyan/u-boot.lds new file mode 100644 index 0000000000..9a6cd1b8a3 --- /dev/null +++ b/package/uboot-lantiq/files/board/arcadyan/u-boot.lds @@ -0,0 +1,70 @@ +/* + * (C) Copyright 2003 + * Wolfgang Denk Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* +OUTPUT_FORMAT("elf32-bigmips", "elf32-bigmips", "elf32-bigmips") +*/ +OUTPUT_FORMAT("elf32-tradbigmips", "elf32-tradbigmips", "elf32-tradbigmips") +OUTPUT_ARCH(mips) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + *(.text) + } + + . = ALIGN(4); + .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) } + + . = ALIGN(4); + .data : { *(.data) } + + . = .; + _gp = ALIGN(16) + 0x7ff0; + + .got : { + __got_start = .; + *(.got) + __got_end = .; + } + + .sdata : { *(.sdata) } + + .u_boot_cmd : { + __u_boot_cmd_start = .; + *(.u_boot_cmd) + __u_boot_cmd_end = .; + } + + uboot_end_data = .; + num_got_entries = (__got_end - __got_start) >> 2; + + . = ALIGN(4); + .sbss (NOLOAD) : { *(.sbss) } + .bss (NOLOAD) : { *(.bss) . = ALIGN(4); } + uboot_end = .; +} diff --git a/package/uboot-lantiq/files/include/configs/arcadyan-common.h b/package/uboot-lantiq/files/include/configs/arcadyan-common.h new file mode 100644 index 0000000000..3bb64312ec --- /dev/null +++ b/package/uboot-lantiq/files/include/configs/arcadyan-common.h @@ -0,0 +1,138 @@ +/* + * (C) Copyright 2003-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * This file contains the configuration parameters for the Danube reference board. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* #define DEBUG */ + +#define CONFIG_MIPS32 1 /* MIPS32 CPU compatible */ +#define CONFIG_MIPS24KEC 1 /* MIPS 24KEc CPU core */ +#define CONFIG_DANUBE 1 /* in a Danube/Twinpass Chip */ + +#define CONFIG_SYS_MIPS_MULTI_CPU 1 /* This is a multi cpu system */ + +#define CONFIG_USE_DDR_RAM + +#define CONFIG_FLASH_CFI_DRIVER 1 + +#define CONFIG_SYS_INIT_RAM_LOCK_MIPS + +#ifdef CONFIG_SYS_RAMBOOT + //#warning CONFIG_SYS_RAMBOOT + #define CONFIG_SKIP_LOWLEVEL_INIT +#else /* CONFIG_SYS_RAMBOOT */ + #define CONFIG_SYS_EBU_BOOT + #define INFINEON_EBU_BOOTCFG 0x688C688C /* CMULT = 8 for 150 MHz */ +#endif /* CONFIG_SYS_RAMBOOT */ + +#if 1 +#ifndef CPU_CLOCK_RATE +#define CPU_CLOCK_RATE (ifx_get_cpuclk()) +#endif +#endif + +#undef CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ + +/* + * Include common defines/options for all Infineon boards + */ +#include "ifx-common.h" + + +#undef CONFIG_EXTRA_ENV_SETTINGS +#define CONFIG_EXTRA_ENV_SETTINGS \ + "ram_addr=0x80500000\0" \ + "kernel_addr=0xb0050000\0" \ + "flashargs=setenv bootargs rootfstype=squashfs,jffs2\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath} \0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off\0" \ + "addmisc=setenv bootargs ${bootargs} init=/etc/preinit " \ + "console=ttyS1,115200 ethaddr=${ethaddr} " \ + "${mtdparts}\0" \ + "flash_flash=run flashargs addip addmisc;" \ + "bootm ${kernel_addr}\0" \ + "flash_nfs=run nfsargs addip addmisc;bootm ${kernel_addr}\0" \ + "net_flash=run load_kernel flashargs addip addmisc;" \ + "bootm ${ram_addr}\0" \ + "net_nfs=run load_kernel nfsargs addip addmisc;" \ + "bootm ${ram_addr}\0" \ + "load_kernel=tftp ${ram_addr} " \ + "${tftppath}openwrt-ifxmips-uImage\0" \ + "update_uboot=tftp 0x80500000 ${tftppath}u-boot-" CONFIG_ARCADYAN ".bin;era 0xb0000000 +${filesize};" \ + "cp.b 0x80500000 0xb0000000 ${filesize}\0" \ + "update_openwrt=tftp ${ram_addr} " \ + "${tftppath}openwrt-lantiq-" CONFIG_ARCADYAN "-squashfs.image;" \ + "era ${kernel_addr} +${filesize};" \ + "cp.b ${ram_addr} ${kernel_addr} ${filesize}\0" + +/* + * Cache Configuration (cpu/chip specific, Danube) + */ +#define CONFIG_SYS_DCACHE_SIZE 16384 +#define CONFIG_SYS_ICACHE_SIZE 16384 +#define CONFIG_SYS_CACHELINE_SIZE 32 +#define CONFIG_SYS_MIPS_CACHE_OPER_MODE CONF_CM_CACHABLE_NO_WA + +#define CONFIG_NET_MULTI + +#define CONFIG_IFX_ETOP +//#define CLK_OUT2_25MHZ + +#define CONFIG_MII +#define CONFIG_CMD_MII + +#define CONFIG_IFX_ASC + +#ifdef CONFIG_USE_ASC0 +#define CONFIG_SYS_IFX_ASC_BASE 0x1E100400 +#else +#define CONFIG_SYS_IFX_ASC_BASE 0x1E100C00 +#endif + +#ifdef CONFIG_SYS_RAMBOOT +/* Configuration of EBU: */ +/* starting address from 0xb0000000 */ +/* make the flash available from RAM boot */ +# define CONFIG_EBU_ADDSEL0 0x10000031 +# define CONFIG_EBU_BUSCON0 0x0001D7FF +# define CONFIG_EBU_ADDSEL1 0x14000001 +# define CONFIG_EBU_BUSCON1 0x4041D7FD +#endif + +#define CONFIG_CMD_HTTPD /* enable upgrade via HTTPD */ + +#define CONFIG_IPADDR 192.168.1.1 +#define CONFIG_SERVERIP 192.168.1.101 +#define CONFIG_GATEWAYIP 192.168.1.254 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_ROOTPATH "/export" + +#endif /* __CONFIG_H */ diff --git a/package/uboot-lantiq/files/include/configs/arv4518.h b/package/uboot-lantiq/files/include/configs/arv4518.h index c4a9842c7a..4c40f0542e 100644 --- a/package/uboot-lantiq/files/include/configs/arv4518.h +++ b/package/uboot-lantiq/files/include/configs/arv4518.h @@ -1,152 +1,14 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ +#ifndef __CONFIG_H_4518 +#define __CONFIG_H_4518 -/* - * This file contains the configuration parameters for the Danube reference board. - */ +#define CONFIG_ARV4518 1 +#define CONFIG_ARCADYAN "ARV4518PW" -#ifndef __CONFIG_H -#define __CONFIG_H - -/* #define DEBUG */ - -#define CONFIG_MIPS32 1 /* MIPS32 CPU compatible */ -#define CONFIG_MIPS24KEC 1 /* MIPS 24KEc CPU core */ -#define CONFIG_DANUBE 1 /* in a Danube/Twinpass Chip */ -#define CONFIG_ARV4518 1 /* on the arv4518 Board */ - -#define CONFIG_SYS_MIPS_MULTI_CPU 1 /* This is a multi cpu system */ - -#define CONFIG_USE_DDR_RAM #define CONFIG_SYS_MAX_RAM 64*1024*1024 +#define CONFIG_SYS_PROMPT "ARV4518 => " +//#define CONFIG_RMII +#define CONFIG_AR8216_SWITCH 1 -#define CONFIG_FLASH_CFI_DRIVER 1 - -#define CONFIG_SYS_INIT_RAM_LOCK_MIPS - -#ifdef CONFIG_SYS_RAMBOOT - //#warning CONFIG_SYS_RAMBOOT - #define CONFIG_SKIP_LOWLEVEL_INIT -#else /* CONFIG_SYS_RAMBOOT */ - #define CONFIG_SYS_EBU_BOOT - #define INFINEON_EBU_BOOTCFG 0x688C688C /* CMULT = 8 for 150 MHz */ -#endif /* CONFIG_SYS_RAMBOOT */ - -#if 1 -#ifndef CPU_CLOCK_RATE -#define CPU_CLOCK_RATE (ifx_get_cpuclk()) -#endif -#endif - -#define CONFIG_SYS_PROMPT "ARV4518 => " /* Monitor Command Prompt */ - -#undef CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ - -/* - * Include common defines/options for all Infineon boards - */ -#include "ifx-common.h" - +#include "arcadyan-common.h" -#undef CONFIG_EXTRA_ENV_SETTINGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ram_addr=0x80500000\0" \ - "kernel_addr=0xb0050000\0" \ - "mtdparts=mtdparts=ifx-nor:256k(uboot)ro,64k(uboot_env)ro,64k(kernel),-(rootfs)\0" \ - "flashargs=setenv bootargs rootfstype=squashfs,jffs2\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath} \0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off\0" \ - "addmisc=setenv bootargs ${bootargs} init=/etc/preinit " \ - "console=ttyS1,115200 ethaddr=${ethaddr} " \ - "${mtdparts}\0" \ - "flash_flash=run flashargs addip addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_nfs=run nfsargs addip addmisc;bootm ${kernel_addr}\0" \ - "net_flash=run load_kernel flashargs addip addmisc;" \ - "bootm ${ram_addr}\0" \ - "net_nfs=run load_kernel nfsargs addip addmisc;" \ - "bootm ${ram_addr}\0" \ - "load_kernel=tftp ${ram_addr} " \ - "${tftppath}openwrt-ifxmips-uImage\0" \ - "update_uboot=tftp 0x80500000 ${tftppath}u-boot.bin;era 0xb0000000 +${filesize};" \ - "cp.b 0x80500000 0xb0000000 ${filesize}\0" \ - "update_openwrt=tftp ${ram_addr} " \ - "${tftppath}openwrt-ifxmips-squashfs.image;" \ - "era ${kernel_addr} +${filesize};" \ - "cp.b ${ram_addr} ${kernel_addr} ${filesize}\0" - -/* - * Cache Configuration (cpu/chip specific, Danube) - */ -#define CONFIG_SYS_DCACHE_SIZE 16384 -#define CONFIG_SYS_ICACHE_SIZE 16384 -#define CONFIG_SYS_CACHELINE_SIZE 32 -#define CONFIG_SYS_MIPS_CACHE_OPER_MODE CONF_CM_CACHABLE_NO_WA - -#define CONFIG_NET_MULTI -#if 0 -#define CONFIG_M4530_ETH -#define CONFIG_M4530_FPGA #endif - -#define CONFIG_IFX_ETOP -//#define CLK_OUT2_25MHZ -#define CONFIG_EXTRA_SWITCH - -//#define CONFIG_RMII /* use interface in RMII mode */ - -#define CONFIG_MII -#define CONFIG_CMD_MII - -#define CONFIG_IFX_ASC - -#ifdef CONFIG_USE_ASC0 -#define CONFIG_SYS_IFX_ASC_BASE 0x1E100400 -#else -#define CONFIG_SYS_IFX_ASC_BASE 0x1E100C00 -#endif - -#ifdef CONFIG_SYS_RAMBOOT -/* Configuration of EBU: */ -/* starting address from 0xb0000000 */ -/* make the flash available from RAM boot */ -# define CONFIG_EBU_ADDSEL0 0x10000031 -# define CONFIG_EBU_BUSCON0 0x0001D7FF -# define CONFIG_EBU_ADDSEL1 0x14000001 -# define CONFIG_EBU_BUSCON1 0x4041D7FD -#endif - -#define CONFIG_CMD_HTTPD /* enable upgrade via HTTPD */ - -//#define CONFIG_ETHADDR 00:13:f7:df:1c:80 -//#define CONFIG_ETHADDR 11:22:33:44:55:66 -#define CONFIG_IPADDR 192.168.2.1 -#define CONFIG_SERVERIP 192.168.2.101 -#define CONFIG_GATEWAYIP 192.168.2.254 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_ROOTPATH "/export" - -#endif /* __CONFIG_H */ diff --git a/package/uboot-lantiq/files/include/configs/arv452c.h b/package/uboot-lantiq/files/include/configs/arv452c.h new file mode 100644 index 0000000000..c4970a2295 --- /dev/null +++ b/package/uboot-lantiq/files/include/configs/arv452c.h @@ -0,0 +1,14 @@ +#ifndef __CONFIG_H_452C +#define __CONFIG_H_452C + +#define CONFIG_ARV4518 1 +#define CONFIG_ARCADYAN "ARV452CPW" + +#define CONFIG_SYS_MAX_RAM 32*1024*1024 +#define CONFIG_SYS_PROMPT "ARV452c => " +#define CONFIG_RMII 1 +#define CONFIG_RTL8306_SWITCH 1 + +#include "arcadyan-common.h" + +#endif diff --git a/package/uboot-lantiq/files/include/configs/arv752DPW.h b/package/uboot-lantiq/files/include/configs/arv752DPW.h new file mode 100644 index 0000000000..a73a87c5ce --- /dev/null +++ b/package/uboot-lantiq/files/include/configs/arv752DPW.h @@ -0,0 +1,20 @@ +#ifndef __CONFIG_H_752DPW +#define __CONFIG_H_752DPW + +#define CONFIG_ARV752DPW 1 +#define CONFIG_ARCADYAN "ARV752DPW" + +#define CONFIG_SYS_MAX_RAM 64*1024*1024 +#define CONFIG_SYS_PROMPT "ARV752DPW => " + +//#define CONFIG_RMII +#define CONFIG_RTL8306_SWITCH 1 +//#define CONFIG_EBU_GPIO 0x2 +#define CONFIG_SWITCH_PORT1 +#define CONFIG_SWITCH_PIN 3 +//#define CONFIG_BUTTON_PORT0 +//#define CONFIG_BUTTON_PIN 12 + +#include "arcadyan-common.h" + +#endif diff --git a/package/uboot-lantiq/files/include/configs/arv752DPW22.h b/package/uboot-lantiq/files/include/configs/arv752DPW22.h new file mode 100644 index 0000000000..5a1a5ada1e --- /dev/null +++ b/package/uboot-lantiq/files/include/configs/arv752DPW22.h @@ -0,0 +1,20 @@ +#ifndef __CONFIG_H_752DPW22 +#define __CONFIG_H_752DPW22 + +#define CONFIG_ARV752DPW22 1 +#define CONFIG_ARCADYAN "ARV752DPW22" + +#define CONFIG_SYS_MAX_RAM 64*1024*1024 +#define CONFIG_SYS_PROMPT "ARV752DPW22 => " + +#define CONFIG_AR8216_SWITCH 1 +#define CONFIG_EBU_GPIO 0x2 +#define CONFIG_SWITCH_PORT1 +#define CONFIG_SWITCH_PIN 3 +#define CONFIG_BUTTON_PORT0 +#define CONFIG_BUTTON_PIN 13 +#define CONFIG_BUTTON_LEVEL 0 + +#include "arcadyan-common.h" + +#endif diff --git a/package/uboot-lantiq/files/include/configs/arv752DWP22.h b/package/uboot-lantiq/files/include/configs/arv752DWP22.h deleted file mode 100644 index 386a2380c6..0000000000 --- a/package/uboot-lantiq/files/include/configs/arv752DWP22.h +++ /dev/null @@ -1,152 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * This file contains the configuration parameters for the Danube reference board. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* #define DEBUG */ - -#define CONFIG_MIPS32 1 /* MIPS32 CPU compatible */ -#define CONFIG_MIPS24KEC 1 /* MIPS 24KEc CPU core */ -#define CONFIG_DANUBE 1 /* in a Danube/Twinpass Chip */ -#define CONFIG_ARV752DWP22 1 /* on the arv752DWP22 Board */ - -#define CONFIG_SYS_MIPS_MULTI_CPU 1 /* This is a multi cpu system */ - -#define CONFIG_USE_DDR_RAM -#define CONFIG_SYS_MAX_RAM 64*1024*1024 - -#define CONFIG_FLASH_CFI_DRIVER 1 - -#define CONFIG_SYS_INIT_RAM_LOCK_MIPS - -#ifdef CONFIG_SYS_RAMBOOT - //#warning CONFIG_SYS_RAMBOOT - #define CONFIG_SKIP_LOWLEVEL_INIT -#else /* CONFIG_SYS_RAMBOOT */ - #define CONFIG_SYS_EBU_BOOT - #define INFINEON_EBU_BOOTCFG 0x688C688C /* CMULT = 8 for 150 MHz */ -#endif /* CONFIG_SYS_RAMBOOT */ - -#if 1 -#ifndef CPU_CLOCK_RATE -#define CPU_CLOCK_RATE (ifx_get_cpuclk()) -#endif -#endif - -#define CONFIG_SYS_PROMPT "ARV752DWP22 => " /* Monitor Command Prompt */ - -#undef CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ - -/* - * Include common defines/options for all Infineon boards - */ -#include "ifx-common.h" - - -#undef CONFIG_EXTRA_ENV_SETTINGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ram_addr=0x80500000\0" \ - "kernel_addr=0xb0050000\0" \ - "mtdparts=mtdparts=ifx-nor:256k(uboot)ro,64k(uboot_env)ro,64k(kernel),-(rootfs)\0" \ - "flashargs=setenv bootargs rootfstype=squashfs,jffs2\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath} \0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off\0" \ - "addmisc=setenv bootargs ${bootargs} init=/etc/preinit " \ - "console=ttyS1,115200 ethaddr=${ethaddr} " \ - "${mtdparts}\0" \ - "flash_flash=run flashargs addip addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_nfs=run nfsargs addip addmisc;bootm ${kernel_addr}\0" \ - "net_flash=run load_kernel flashargs addip addmisc;" \ - "bootm ${ram_addr}\0" \ - "net_nfs=run load_kernel nfsargs addip addmisc;" \ - "bootm ${ram_addr}\0" \ - "load_kernel=tftp ${ram_addr} " \ - "${tftppath}openwrt-ifxmips-uImage\0" \ - "update_uboot=tftp 0x80500000 ${tftppath}u-boot.bin;era 0xb0000000 +${filesize};" \ - "cp.b 0x80500000 0xb0000000 ${filesize}\0" \ - "update_openwrt=tftp ${ram_addr} " \ - "${tftppath}openwrt-ifxmips-squashfs.image;" \ - "era ${kernel_addr} +${filesize};" \ - "cp.b ${ram_addr} ${kernel_addr} ${filesize}\0" - -/* - * Cache Configuration (cpu/chip specific, Danube) - */ -#define CONFIG_SYS_DCACHE_SIZE 16384 -#define CONFIG_SYS_ICACHE_SIZE 16384 -#define CONFIG_SYS_CACHELINE_SIZE 32 -#define CONFIG_SYS_MIPS_CACHE_OPER_MODE CONF_CM_CACHABLE_NO_WA - -#define CONFIG_NET_MULTI -#if 0 -#define CONFIG_M4530_ETH -#define CONFIG_M4530_FPGA -#endif - -#define CONFIG_IFX_ETOP -//#define CLK_OUT2_25MHZ -#define CONFIG_EXTRA_SWITCH - -//#define CONFIG_RMII /* use interface in RMII mode */ - -#define CONFIG_MII -#define CONFIG_CMD_MII - -#define CONFIG_IFX_ASC - -#ifdef CONFIG_USE_ASC0 -#define CONFIG_SYS_IFX_ASC_BASE 0x1E100400 -#else -#define CONFIG_SYS_IFX_ASC_BASE 0x1E100C00 -#endif - -#ifdef CONFIG_SYS_RAMBOOT -/* Configuration of EBU: */ -/* starting address from 0xb0000000 */ -/* make the flash available from RAM boot */ -# define CONFIG_EBU_ADDSEL0 0x10000031 -# define CONFIG_EBU_BUSCON0 0x0001D7FF -# define CONFIG_EBU_ADDSEL1 0x14000001 -# define CONFIG_EBU_BUSCON1 0x4041D7FD -#endif - -#define CONFIG_CMD_HTTPD /* enable upgrade via HTTPD */ - -//#define CONFIG_ETHADDR 00:13:f7:df:1c:80 -//#define CONFIG_ETHADDR 11:22:33:44:55:66 -#define CONFIG_IPADDR 192.168.2.1 -#define CONFIG_SERVERIP 192.168.2.101 -#define CONFIG_GATEWAYIP 192.168.2.254 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_ROOTPATH "/export" - -#endif /* __CONFIG_H */ diff --git a/package/uboot-lantiq/files/include/configs/ifx-common.h b/package/uboot-lantiq/files/include/configs/ifx-common.h index e4e8067d74..c0a1b6b208 100644 --- a/package/uboot-lantiq/files/include/configs/ifx-common.h +++ b/package/uboot-lantiq/files/include/configs/ifx-common.h @@ -23,7 +23,7 @@ #ifndef __IFX_COMMON_H #define __IFX_COMMON_H -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ #define CONFIG_BAUDRATE 115200 -- cgit v1.2.3