juhosg [Sat, 22 Feb 2014 16:26:55 +0000 (16:26 +0000)]
ar71xx/mikrotik: enable small sector erase in the m25p80 driver
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.
nbd [Sat, 22 Feb 2014 14:42:48 +0000 (14:42 +0000)]
gianfar: Fix reported number of sent bytes to BQL
This is a backported patch for the gianfar ethernet driver
used in TPLink 4900 v1. It is supposed to fix the error which
show up in dmesg with:
NETDEV WATCHDOG: eth0 (fsl-gianfar): transmit queue xy timed out
Full upstream patch is at: http://patchwork.ozlabs.org/patch/271242
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39692 3c298f89-4303-0410-b956-a3cf2f4a3e73
jogo [Sat, 22 Feb 2014 11:16:44 +0000 (11:16 +0000)]
brcm63xx: fix number of switch ports for BCM63168/63268
BCM63168 has 6 ports (3 FE PHY, 1 GE PHY, two RGMII) and BCM63268
has two additional RGMII ports, making it 8.
Fix this by checking the chip variant and applying an appropriate
limit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39677 3c298f89-4303-0410-b956-a3cf2f4a3e73
jogo [Sat, 22 Feb 2014 11:16:35 +0000 (11:16 +0000)]
brcm63xx: Add profile and build image for Sagemcom F@ST2704V2 ADSL router
This adds profile and build image for Sagemcom F@st2704, using b43
driver.
For WiFi to work properly BCMA fallback SPROM support patch must
be applied (http://git.io/z1Ki8A).
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4212/ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39673 3c298f89-4303-0410-b956-a3cf2f4a3e73
jogo [Sat, 22 Feb 2014 11:16:30 +0000 (11:16 +0000)]
brcm63xx: Add kernel support for Sagemcom F@ST2704V2 ADSL router
This adds kernel support support for Sagemcom F@st 2704 wireless ADSL
router.
It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+
modem equipped with 64 MiB RAM and 8 MiB flash.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4266/ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39671 3c298f89-4303-0410-b956-a3cf2f4a3e73
jow [Thu, 20 Feb 2014 23:20:10 +0000 (23:20 +0000)]
firewall: fix several ipset integration issues (#15016)
- Do not consider bitmap storage for IPv6 family sets
- Move ipset family parameter before any additional option
- Only emit family parameter for hash sets
- Do not allow IPv6 iprange for IPv4 sets and vice versa
luka [Thu, 20 Feb 2014 17:26:10 +0000 (17:26 +0000)]
imx6: update Ventana dts
Update the Ventana device-tree to match upstream:
- Add IMX6Q/IMX6DL variants for GW54xx/GW53xx/GW52xx/GW51xx
- align pinctrl with upstream
- consolidate multiple patches into one
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39644 3c298f89-4303-0410-b956-a3cf2f4a3e73
juhosg [Thu, 20 Feb 2014 17:07:51 +0000 (17:07 +0000)]
ar71xx: Add support for MikroTik RB951Ui-2HnD
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names] Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39641 3c298f89-4303-0410-b956-a3cf2f4a3e73
nbd [Wed, 19 Feb 2014 19:20:10 +0000 (19:20 +0000)]
gcc: prevent the use of LDRD/STRD on ARMv5TE
These instructions are for 64-bit load/store. On ARMv5TE, the CPU
requires addresses to be aligned to 64-bit. When misaligned, behavior is
undefined (effectively either loads the same word twice on LDRD, or
corrupts surrounding memory on STRD).
On ARMv6 and newer, unaligned access is safe.
Removing these instructions for ARMv5TE is necessary, because GCC
ignores alignment information in pointers and does unsafe optimizations
that have shown up as bugs in various places.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39638 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without this patch, UART output will show only 4 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000050000 : "u-boot"
[ 0.760000] 0x000000050000-0x000000070000 : "u-boot-env"
[ 0.770000] 0x000000070000-0x0000007f0000 : "firmware"
[ 0.790000] 0x0000007f0000-0x000000800000 : "art"
and then linux complains :VFS: Cannot open root device "(null)"
With this patch, UART out will show 7 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.770000] 0x000000050000-0x0000007f0000 : "firmware"
[ 0.780000] 2 netgear-fw partitions found on MTD device firmware
[ 0.780000] 0x000000050000-0x00000014b440 : "kernel"
[ 0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.800000] 0x00000014b440-0x0000007f0000 : "rootfs"
[ 0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.820000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.830000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data"
[ 0.840000] 0x0000007f0000-0x000000800000 : "art"
luka [Sat, 15 Feb 2014 23:53:10 +0000 (23:53 +0000)]
kirkwood: update support for dockstar
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-dockstar-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org> Tested-by: Alexander Couzens <lynxis@fe80.eu> CC: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39593 3c298f89-4303-0410-b956-a3cf2f4a3e73
luka [Sat, 15 Feb 2014 23:53:09 +0000 (23:53 +0000)]
kirkwood: update support for ib62x0
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-ib62x0-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org> Tested-by: Luka Perkov <luka@openwrt.org> CC: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39592 3c298f89-4303-0410-b956-a3cf2f4a3e73
luka [Sat, 15 Feb 2014 23:53:08 +0000 (23:53 +0000)]
kirkwood: update support for iconnect
Previous patch was pushed due to false user report. While at it fix alphabetic
ordering.
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0x1fe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-iconnect-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org> CC: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39591 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some users are avoiding to replace their bootloader, because of that add
support for second stage u-boot image. Having ubifs capable bootloader is
required in order to boot current OpenWrt trunk.
Sample ib62x0 commands for running second stage bootloader:
While at it include parallel build support, use alphabetic order of the boards
and introduce common OpenWrt configuration.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by (on ib62x0): Luka Perkov <luka@openwrt.org>
Tested-by (on dockstar): Alexander Couzens <lynxis@fe80.eu>
Tested-by (on iconnect): Wojciech Dubowik <wojciech.dubowik@neratec.com> CC: Felix Kaechele <heffer@fedoraproject.org> CC: Wojciech Dubowik <wojciech.dubowik@neratec.com> CC: Alexander Couzens <lynxis@fe80.eu> CC: Daniel Engberg <daniel.engberg@pyret.net> CC: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39590 3c298f89-4303-0410-b956-a3cf2f4a3e73