-@@ -1991,6 +2002,10 @@ enum nl80211_sta_bss_param {
- * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode
- * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards
- * non-peer STA
-+ * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
-+ * Contains a nested array of signal strength attributes (u8, dBm)
-+ * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
-+ * Same format as NL80211_STA_INFO_CHAIN_SIGNAL.
- * @__NL80211_STA_INFO_AFTER_LAST: internal
- * @NL80211_STA_INFO_MAX: highest possible station info attribute
- */
-@@ -2020,6 +2035,8 @@ enum nl80211_sta_info {
- NL80211_STA_INFO_NONPEER_PM,
- NL80211_STA_INFO_RX_BYTES64,
- NL80211_STA_INFO_TX_BYTES64,
-+ NL80211_STA_INFO_CHAIN_SIGNAL,
-+ NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
-
- /* keep last */
- __NL80211_STA_INFO_AFTER_LAST,
-@@ -2413,6 +2430,8 @@ enum nl80211_survey_info {
- * @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering
- * @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing.
- * overrides all other flags.
-+ * @NL80211_MNTR_FLAG_ACTIVE: use the configured MAC address
-+ * and ACK incoming unicast packets.
- *
- * @__NL80211_MNTR_FLAG_AFTER_LAST: internal use
- * @NL80211_MNTR_FLAG_MAX: highest possible monitor flag
-@@ -2424,6 +2443,7 @@ enum nl80211_mntr_flags {
- NL80211_MNTR_FLAG_CONTROL,
- NL80211_MNTR_FLAG_OTHER_BSS,
- NL80211_MNTR_FLAG_COOK_FRAMES,
-+ NL80211_MNTR_FLAG_ACTIVE,
-
- /* keep last */
- __NL80211_MNTR_FLAG_AFTER_LAST,
-@@ -2559,6 +2579,10 @@ enum nl80211_mesh_power_mode {
- *
- * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs)
- *
-+ * @NL80211_MESHCONF_PLINK_TIMEOUT: If no tx activity is seen from a STA we've
-+ * established peering with for longer than this time (in seconds), then
-+ * remove it from the STA's list of peers. Default is 30 minutes.
-+ *
- * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
- */
- enum nl80211_meshconf_params {
-@@ -2590,6 +2614,7 @@ enum nl80211_meshconf_params {
- NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL,
- NL80211_MESHCONF_POWER_MODE,
- NL80211_MESHCONF_AWAKE_WINDOW,
-+ NL80211_MESHCONF_PLINK_TIMEOUT,
-
- /* keep last */
- __NL80211_MESHCONF_ATTR_AFTER_LAST,
-@@ -2637,6 +2662,10 @@ enum nl80211_meshconf_params {
- * @NL80211_MESH_SETUP_USERSPACE_MPM: Enable this option if userspace will
- * implement an MPM which handles peer allocation and state.
- *
-+ * @NL80211_MESH_SETUP_AUTH_PROTOCOL: Inform the kernel of the authentication
-+ * method (u8, as defined in IEEE 8.4.2.100.6, e.g. 0x1 for SAE).
-+ * Default is no authentication method required.
-+ *
- * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
- *
- * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
-@@ -2650,6 +2679,7 @@ enum nl80211_mesh_setup_params {
- NL80211_MESH_SETUP_USERSPACE_AMPE,
- NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC,
- NL80211_MESH_SETUP_USERSPACE_MPM,
-+ NL80211_MESH_SETUP_AUTH_PROTOCOL,
-
- /* keep last */
- __NL80211_MESH_SETUP_ATTR_AFTER_LAST,
-@@ -2730,6 +2760,8 @@ enum nl80211_channel_type {
- * and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well
- * @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
- * attribute must be provided as well
-+ * @NL80211_CHAN_WIDTH_5: 5 MHz OFDM channel
-+ * @NL80211_CHAN_WIDTH_10: 10 MHz OFDM channel
- */
- enum nl80211_chan_width {
- NL80211_CHAN_WIDTH_20_NOHT,
-@@ -2738,6 +2770,8 @@ enum nl80211_chan_width {
- NL80211_CHAN_WIDTH_80,
- NL80211_CHAN_WIDTH_80P80,
- NL80211_CHAN_WIDTH_160,
-+ NL80211_CHAN_WIDTH_5,
-+ NL80211_CHAN_WIDTH_10,
- };
-
- /**
-@@ -3028,11 +3062,11 @@ enum nl80211_tx_power_setting {
- };
-
- /**
-- * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute
-- * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute
-- * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has
-+ * enum nl80211_packet_pattern_attr - packet pattern attribute
-+ * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
-+ * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
- * a zero bit are ignored
-- * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have
-+ * @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have
- * a bit for each byte in the pattern. The lowest-order bit corresponds
- * to the first byte of the pattern, but the bytes of the pattern are
- * in a little-endian-like format, i.e. the 9th byte of the pattern
-@@ -3043,23 +3077,23 @@ enum nl80211_tx_power_setting {
- * Note that the pattern matching is done as though frames were not
- * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
- * first (including SNAP header unpacking) and then matched.
-- * @NL80211_WOWLAN_PKTPAT_OFFSET: packet offset, pattern is matched after
-+ * @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after
- * these fixed number of bytes of received packet
-- * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes
-- * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number
-+ * @NUM_NL80211_PKTPAT: number of attributes
-+ * @MAX_NL80211_PKTPAT: max attribute number
- */
--enum nl80211_wowlan_packet_pattern_attr {
-- __NL80211_WOWLAN_PKTPAT_INVALID,
-- NL80211_WOWLAN_PKTPAT_MASK,
-- NL80211_WOWLAN_PKTPAT_PATTERN,
-- NL80211_WOWLAN_PKTPAT_OFFSET,
-+enum nl80211_packet_pattern_attr {
-+ __NL80211_PKTPAT_INVALID,
-+ NL80211_PKTPAT_MASK,
-+ NL80211_PKTPAT_PATTERN,
-+ NL80211_PKTPAT_OFFSET,
-
-- NUM_NL80211_WOWLAN_PKTPAT,
-- MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1,
-+ NUM_NL80211_PKTPAT,
-+ MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1,
- };
-
- /**
-- * struct nl80211_wowlan_pattern_support - pattern support information
-+ * struct nl80211_pattern_support - packet pattern support information
- * @max_patterns: maximum number of patterns supported
- * @min_pattern_len: minimum length of each pattern
- * @max_pattern_len: maximum length of each pattern
-@@ -3069,13 +3103,22 @@ enum nl80211_wowlan_packet_pattern_attr
- * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the
- * capability information given by the kernel to userspace.
- */
--struct nl80211_wowlan_pattern_support {
-+struct nl80211_pattern_support {
- __u32 max_patterns;
- __u32 min_pattern_len;
- __u32 max_pattern_len;
- __u32 max_pkt_offset;
- } __attribute__((packed));
-
-+/* only for backward compatibility */
-+#define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID
-+#define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK
-+#define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN
-+#define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET
-+#define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT
-+#define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT
-+#define nl80211_wowlan_pattern_support nl80211_pattern_support
-+
- /**
- * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
- * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
-@@ -3095,7 +3138,7 @@ struct nl80211_wowlan_pattern_support {
- * pattern matching is done after the packet is converted to the MSDU.
- *
- * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
-- * carrying a &struct nl80211_wowlan_pattern_support.
-+ * carrying a &struct nl80211_pattern_support.
- *
- * When reporting wakeup. it is a u32 attribute containing the 0-based
- * index of the pattern that caused the wakeup, in the patterns passed
-@@ -3252,7 +3295,7 @@ struct nl80211_wowlan_tcp_data_token_fea
- * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a
- * u32 attribute holding the maximum length
- * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for
-- * feature advertising. The mask works like @NL80211_WOWLAN_PKTPAT_MASK
-+ * feature advertising. The mask works like @NL80211_PKTPAT_MASK
- * but on the TCP payload only.
- * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes
- * @MAX_NL80211_WOWLAN_TCP: highest attribute number
-@@ -3556,6 +3599,10 @@ enum nl80211_ap_sme_features {
- * Peering Management entity which may be implemented by registering for
- * beacons or NL80211_CMD_NEW_PEER_CANDIDATE events. The mesh beacon is
- * still generated by the driver.
-+ * @NL80211_FEATURE_ACTIVE_MONITOR: This driver supports an active monitor
-+ * interface. An active monitor interface behaves like a normal monitor
-+ * interface, but gets added to the driver. It ensures that incoming
-+ * unicast packets directed at the configured interface address get ACKed.
- */
- enum nl80211_feature_flags {
- NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
-@@ -3575,6 +3622,7 @@ enum nl80211_feature_flags {
- NL80211_FEATURE_ADVERTISE_CHAN_LIMITS = 1 << 14,
- NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15,
- NL80211_FEATURE_USERSPACE_MPM = 1 << 16,
-+ NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17,
- };
-
- /**