X-Git-Url: https://git.enpas.org/?a=blobdiff_plain;f=openwrt%2Fscripts%2Fflash.sh;h=8841c3568464932c88da8ddd3890f1395690ad72;hb=3e7ce96bd455858a0c157d631c9b8a5e9c0848ad;hp=aedb25072ca751134679058c6ce1f28cbc627459;hpb=d2b94be30cae972e5bd43f530e7d9fb44c5173d0;p=openwrt.git diff --git a/openwrt/scripts/flash.sh b/openwrt/scripts/flash.sh index aedb25072c..8841c35684 100644 --- a/openwrt/scripts/flash.sh +++ b/openwrt/scripts/flash.sh @@ -1,9 +1,9 @@ #!/bin/bash - -# flash script for linksys and asus routers +# +# tftp flash script for wireless routers # # Copyright (C) 2004 by Oleg I. Vdovikin -# Copyright (C) 2005 by Waldemar Brodkorb +# Copyright (C) 2005 by Waldemar Brodkorb # # This program is free software; you can redistribute it and/or modify # it under the terms of the GNU General Public License as published by @@ -24,20 +24,28 @@ if [ -z "$1" ] || [ ! -f $1 ] || [ -z $2 ]; then echo Usage: $0 firmware vendor cat << EOF IMPORTANT: -Notes for Linksys Routers: +Notes for Linksys / Asus WL500gx router: be sure you have set boot_wait to yes. Power on your router after executing this script. - Use openwrt-gs-code.bin or openwrt-g-code.bin as firmware. -Notes for Asus Routers: - be sure POWER led is flashing (If this is not a case +Notes for Asus WL500g router: + be sure POWER led is flashing (If this is not the case poweroff the device, push the reset button & power on it again, then release button) - Use openwrt-linux.trx as firmware. 1) connect your pc to the LAN port 2) be sure your link is up and has an address in the 192.168.1.0/24 address range (and not the 192.168.1.1) + +Notes for Toshiba router: + boot_wait is enabled by default on these units. + +1) connect your pc to any of the four LAN ports +2) be sure your link is up and has an address in the + 192.168.10.1/24 address range (and not the 192.168.10.1) +3) run this script (unit will only accept .trx images) +4) Turn unit power on. + EOF exit 0 fi @@ -50,5 +58,9 @@ echo Please wait until leds stops flashing. elif [ "$2" == "linksys" ]; then echo Flashing 192.168.1.1 using $1... echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.1.1 -echo Please wait until power led stops flashing. Then you can login via telnet 192.168.1.1 +echo Please wait until power led stops flashing. Do not poweroff! Then you can login via telnet 192.168.1.1. +elif [ "$2" == "toshiba" ]; then +echo Flashing 192.168.10.1 using $1... +echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.10.1 +echo Unit will automatically reboot within 5 minutes. Do not power off. Then you can login via telnet 192.168.10.1. fi